Schlage user manual SRP-275 Connecting the cables, Connecting the AC Adaptor

Page 10

SRP-275

2. Connecting the cables

2-1 Connecting the AC Adaptor

AC adaptor

Power connector

Power cord

CAUTION

• Connect the AC adapter according to the following procedure.

1)Make sure the printer is turned off.

2)Before inserting the AC adaptor, connect the power cord.

3)Insert the AC adaptor as shown.

4)Plug the AC adapter cable into the printer’s power connector.

5)Plug the power cord into the outlet, and turn on the power.

Before connecting the printer to the power supply, make sure that the voltage and power specifications match the printer’s requirements. Using an incorrect power supply can cause serious damage to the printer.

2-2 Connecting the Interface cable and Drawer kick-out cable

Interface connector

Drawer kick-out connector

Drawer kick-out cable

Serial/ Parallel/ USB/ Ethernet

Interface cable

NOTES

• Connect the cables according to the following procedure.

1)Turn off printer and the host ECR (host computer).

2)Plug the interface cable into the interface connector on the printer then fasten the screw on both sides of the connector.

3)Plug the drawer kick-out cable into the drawer kick-out connector on the printer.

(When removing the drawer kick-out cable, press on the connector’s clip while pulling out.)

Connect the printer to the host ECR (host computer) though an interface cable matching the specification of the printer and the host ECR (host computer). Be sure to use a drawer that matches the printer’s specification.

Depending on the interface your system uses, either connect the serial, parallel, USB or Ethernet communication cable to the appropriate connector on the back of the printer. Cables are provided by your dealer or system installer.

Rev. 1.01

- 10 -

Image 10

Contents SRP-275 SRP-275 Safety Precautions Do not plug several products in one multi-outletSRP-275 To UnplugSRP-275 Waste Electrical and Electric Equipment Weee SRP-275 EMC and Safety standards AppliedCE Marking Label MaterialFront view SRP-275 IntroductionRear view SRP-275 Table of Contents Unpacking SRP-275 Setting Up the PrinterChoosing a place for the printer Error LED Red Color Using the operation panelControl panel Power LED Green Color Paper OUT LED Red ColorConnecting the Interface cable and Drawer kick-out cable SRP-275 Connecting the cablesConnecting the AC Adaptor Connect the AC adapter according to the following procedureSerial Interface RS-232C Interface connectorConnector Drawer kick-outPin no Source Compatibility mode Nibble mode Byte mode Parallel Interface IEEE1284Drawer kick-out USB InterfaceEthernet Interface Pin No Description DirectionSetting the DIP Switch SRP-275 Setting the SwitchesDIP Switch setting for EpsonESC/POS mode DIP Switch setting for CitizeniDP 3550 mode International Character Selection DSW Code CountryDIP Switch setting for StarSP500 mode Emulation Selection DSW 1-1Changing the DIP Switch setting Memory Switch Function Setting the Memory SwitchesMemory Switch setting for EpsonESC/POS mode OffCustomize value Function Selectable value Serial communication Function Selectable valueMemory Switch Setup Mode Example of Memory Switch setup sheetProcedure of Memory Switch setting Settings Memory Switch setting for Star modeFunction Class Default Settings Function Memory Switch Bit DbcsMemory Switch Bit Function MSW 2-ACharacter Table *2 Memory Switch Bit Function Reserved SRP-275 Ribbon Cassette Installation SRP-275 Roll Paper Installation SRP-275 Changing the paper width SRP-275 Installing the wall mount Option SRP-275 Self Test SRP-275 Hexadecimal Dumping To use the hexadecimal dump feature, follow these stepsHexadecimal dump Paper specifications SpecificationPrinting specification Ribbon cassette specificationReliability Electrical characteristicsEnvironment conditions Dimensions Dimensions & weightOptional features WeightRecoverable errors SRP-275 Appendix TroubleshootingError LED blinking pattern Error Description Error LED blinking pattern RecoveryPrinter does not start printing If any of the lights are on, please check the followingPrinting is poor Printer stops printingYou want to check the operation of the printer by itself Self test