Schlage SRP-275 Setting the Memory Switches, Memory Switch setting for EpsonESC/POS mode, Off

Page 18

SRP-275

3-2 Setting the Memory Switches

3-2-1 Memory Switch setting for Epson(ESC/POS) mode

This printer has “Memory Switch” set which is software switches. Memory Switch set has “MSW 2”, “MSW 8”, “Customize value”, “Serial communication condition”. “Memory Switch setting utility” can change the Memory Switch set to ON or OFF as shown in the table below (default: all OFF):

NOTES

The Memory Switch is available to be changed by three methods:

-Memory Switch setting utility

-Memory Switch setup mode (there are limitations on what can be changed)

-Control from ESC/POS command

-Some Memory Switch settings can be changed by the “Memory Switch setting mode”. See “Procedure of Memory Switch setting”.

Settings of the Memory Switch are stored in the NV memory; therefore, even if the printer is turned off, the settings are maintained. When you replace a SRP-270 with a SRP-275, you should adjust the MSW 8-5 to OFF.

• Memory Switch 2

Switch

Function

1Reserved

2Reserved

3Reserved for Chinese selection

4~8 Code page selection (*1)

On

Off

-

Fixed to Off

-

Fixed to Off

-

Fixed to Off

Refer to the following table

NOTES

Desired code page can be selected using Memory Switch 2-4~8 by setting as following.

(*1) Code page selection

MSW 2-8

 

MSW 2-7

MSW 2-6

MSW 2-5

MSW 2-4

Character Table

0

 

0

0

0

0

Page 0 (PC437 : U.S.A.)

0

 

0

0

0

1

Page 1 (Katakana)

0

 

0

0

1

0

Page 2 (PC850 : Multilingual)

0

 

0

0

1

1

Page 3 (PC860 : Portuguese)

0

 

0

1

0

0

Page 4 (PC863 : Canadian-French)

0

 

0

1

0

1

Page 5 (PC865 : Nordic)

0

 

0

1

1

0

Page 16 (WPC1252 : Latin1)

0

 

0

1

1

1

Page 17 (PC866 : Russian)

0

 

1

0

0

0

Page 18 (PC852 : Latin2)

0

 

1

0

0

1

Page 19 (PC858 : Euro)

0

 

1

0

1

0

Page 21 (PC862 : Israel)

0

 

1

0

1

1

Page 22 (PC864 : Arabic)

0

 

1

1

0

0

Page 23 (Thai character code 42)

0

 

1

1

0

1

Page 24 (WPC1253 : Greek)

0

 

1

1

1

0

Page 25 (WPC1254 : Turkish)

0

 

1

1

1

1

Page 26 (WPC1257 : Baltic)

1

 

0

0

0

0

Page 27 (Farsi) (*2)

1

 

0

0

0

1

Page 28 (WPC1251 : Russian) (*2)

1

 

0

0

1

0

Page 29 (PC737 : Greek) (*2)

1

 

0

0

1

1

Page 30 (PC775 : Baltic) (*2)

1

 

0

1

0

0

Page 31 (Thai character code 14)

1

 

0

1

0

1

Page 32 (OldCode : Israel)

1

 

0

1

1

0

Page 33 (WPC1255 : Israel)

1

 

0

1

1

1

Page 34 (Thai character code 11)

1

 

1

0

0

0

Page 35 (Thai character code 18)

1

 

1

0

1

0

Page 37 (PC857 : Turkish)

1

 

1

0

1

1

Page 38 (PC928 : Greek)

(*2) Only Font B available.

 

 

 

Rev. 1.01

 

 

 

- 18 -

 

Image 18
Contents SRP-275 SRP-275 Safety Precautions Do not plug several products in one multi-outletSRP-275 To UnplugSRP-275 Waste Electrical and Electric Equipment Weee SRP-275 EMC and Safety standards AppliedCE Marking Label MaterialSRP-275 Introduction Front viewRear view SRP-275 Table of Contents SRP-275 Setting Up the Printer UnpackingChoosing a place for the printer Error LED Red Color Using the operation panelControl panel Power LED Green Color Paper OUT LED Red ColorConnecting the Interface cable and Drawer kick-out cable SRP-275 Connecting the cablesConnecting the AC Adaptor Connect the AC adapter according to the following procedureSerial Interface RS-232C Interface connectorConnector Drawer kick-outPin no Source Compatibility mode Nibble mode Byte mode Parallel Interface IEEE1284Drawer kick-out USB InterfaceEthernet Interface Pin No Description DirectionSRP-275 Setting the Switches Setting the DIP SwitchDIP Switch setting for EpsonESC/POS mode DIP Switch setting for CitizeniDP 3550 mode International Character Selection DSW Code CountryDIP Switch setting for StarSP500 mode Emulation Selection DSW 1-1Changing the DIP Switch setting Memory Switch Function Setting the Memory SwitchesMemory Switch setting for EpsonESC/POS mode OffCustomize value Function Selectable value Serial communication Function Selectable valueMemory Switch Setup Mode Example of Memory Switch setup sheetProcedure of Memory Switch setting Memory Switch setting for Star mode SettingsFunction Class Default Settings Function Memory Switch Bit DbcsMemory Switch Bit Function MSW 2-ACharacter Table *2 Memory Switch Bit Function Reserved SRP-275 Ribbon Cassette Installation SRP-275 Roll Paper Installation SRP-275 Changing the paper width SRP-275 Installing the wall mount Option SRP-275 Self Test To use the hexadecimal dump feature, follow these steps SRP-275 Hexadecimal DumpingHexadecimal dump Paper specifications SpecificationPrinting specification Ribbon cassette specificationElectrical characteristics ReliabilityEnvironment conditions Dimensions Dimensions & weightOptional features WeightRecoverable errors SRP-275 Appendix TroubleshootingError LED blinking pattern Error Description Error LED blinking pattern RecoveryPrinter does not start printing If any of the lights are on, please check the followingPrinting is poor Printer stops printingYou want to check the operation of the printer by itself Self test