Schlage SRP-275 user manual DIP Switch setting for StarSP500 mode, Emulation Selection DSW 1-1

Page 16

					SRP-275
3-1-3 DIP Switch setting for Star(SP500) mode
• DIP Switch 1

Switch	Function		ON	OFF		Default
1-1	Emulation Selection (*1)		Refer to the following table			OFF
1-2	Emulation Selection (*1)		Refer to the following table			OFF
1-2
1-3	Auto cutter		Enable	Disable		OFF
1-4	Black/Red Printing		Enable	Disable		OFF
1-5
1-6		Reserved				OFF
1-7		Reserved				OFF
1-7
1-8

• DIP Switch 2 (RS232C serial interface model)

Switch				Function			ON	OFF	Default
2-1					Reserved				OFF
2-2					Reserved				OFF
2-2
2-3		Hand shaking				XON/XOFF		DTR/DSR	OFF
2-4		Word length					7 bits	8 bits	OFF
2-5		Parity check					Enable	Disable	OFF
2-6		Parity selection					EVEN	ODD	OFF
2-7		Baud rate selection (*2)					Refer to the following table		OFF
2-8		Baud rate selection (*2)					Refer to the following table		OFF
2-8									OFF
NOTES
(*1) Emulation Selection (DSW 1-1 and 1-2)

Emulation				1-1	1-2
EPSON				OFF	OFF
STAR				OFF	ON
CITIZEN				ON	OFF
EPSON-KP				ON	ON

- EPSON-KP(EPSON Kitchen Printer mode) : A alarm is generated by printer after auto cutting and in paper end error.

(*2) Baud rate selection (Transmission speed)

Transmission	2-7	2-8
2400 baud	ON	ON
4800 baud	OFF	ON
9600 baud	OFF	OFF
19200 baud	ON	OFF

NOTICE

Change in DIP Switch settings are recognized only when the printer power is turned on or when the printer is reset by using the interface. If the DIP Switch setting is changed after the printer power is turned on, the change does not take effect until the printer is turned on again or is reset.

Rev. 1.01

- 16 -

Image 16

Contents SRP-275 SRP-275 Safety Precautions Do not plug several products in one multi-outletSRP-275 To UnplugSRP-275 SRP-275 EMC and Safety standards Applied CE MarkingWaste Electrical and Electric Equipment Weee Label MaterialFront view SRP-275 IntroductionRear view SRP-275 Table of Contents Unpacking SRP-275 Setting Up the PrinterChoosing a place for the printer Using the operation panel Control panel Power LED Green ColorError LED Red Color Paper OUT LED Red ColorSRP-275 Connecting the cables Connecting the AC AdaptorConnecting the Interface cable and Drawer kick-out cable Connect the AC adapter according to the following procedureInterface connector ConnectorSerial Interface RS-232C Drawer kick-outPin no Source Compatibility mode Nibble mode Byte mode Parallel Interface IEEE1284USB Interface Ethernet InterfaceDrawer kick-out Pin No Description DirectionSetting the DIP Switch SRP-275 Setting the SwitchesDIP Switch setting for EpsonESC/POS mode DIP Switch setting for CitizeniDP 3550 mode International Character Selection DSW Code CountryDIP Switch setting for StarSP500 mode Emulation Selection DSW 1-1Changing the DIP Switch setting Setting the Memory Switches Memory Switch setting for EpsonESC/POS modeMemory Switch Function OffCustomize value Function Selectable value Serial communication Function Selectable valueMemory Switch Setup Mode Example of Memory Switch setup sheetProcedure of Memory Switch setting Settings Memory Switch setting for Star modeFunction Class Default Settings Function Memory Switch Bit DbcsMemory Switch Bit Function MSW 2-ACharacter Table *2 Memory Switch Bit Function Reserved SRP-275 Ribbon Cassette Installation SRP-275 Roll Paper Installation SRP-275 Changing the paper width SRP-275 Installing the wall mount Option SRP-275 Self Test SRP-275 Hexadecimal Dumping To use the hexadecimal dump feature, follow these stepsHexadecimal dump Specification Printing specificationPaper specifications Ribbon cassette specificationReliability Electrical characteristicsEnvironment conditions Dimensions & weight Optional featuresDimensions WeightSRP-275 Appendix Troubleshooting Error LED blinking patternRecoverable errors Error Description Error LED blinking pattern RecoveryPrinter does not start printing If any of the lights are on, please check the followingPrinter stops printing You want to check the operation of the printer by itselfPrinting is poor Self test