Schlage SRP-275 user manual Parallel Interface IEEE1284

Page 12

SRP-275

2-2-2 Parallel Interface (IEEE1284)

	IFC-P TYPE	Drawer kick-out
	Interface connector
		Connector

Pin no.	Source	Compatibility mode	Nibble mode	Byte mode
1	Host	nStrobe	HostClk	HostClk

2	Host / Printer	Data 0 (LSB)	-	Data 0 (LSB)
3	Host / Printer	Data 1	-	Data 1

4	Host / Printer	Data 2	-	Data 2

5	Host / Printer	Data 3	-	Data 3

6	Host / Printer	Data 4	-	Data 4

7	Host / Printer	Data 5	-	Data 5

8	Host / Printer	Data 6	-	Data 6

9	Host / Printer	Data 7 (MSB)	-	Data 7 (MSB)

10	Printer	nAck	PtrClk	PtrClk

11	Printer	Busy	PtrBusy / Data3,7	PtrBusy

12	Printer	Perror	AckDataReq / Data2,6	AckDataReq

13	Printer	Select	Xflag / Data1,5	Xflag

14	Host	nAutoFd	HostBusy	HostBusy

15	-	NC	ND	ND

16	-	GND	GND	GND

17	-	GND	FG	FG

18	Printer	Logic-H	Logic-H	Logic-H

19~30	-	GND	GND	GND

31	Host	nInit	nInit	nInit

32	Printer	nFault	nDataAbail /	nDataAvail

33	-	NC	ND	ND

34	Printer	NC	ND	ND

35	Printer	NC	ND	ND

36	Host	nSelectln	1284-Active	1284-Active

Rev. 1.01

- 12 -

Image 12

Contents SRP-275 SRP-275 Safety Precautions Do not plug several products in one multi-outletSRP-275 To UnplugSRP-275 SRP-275 EMC and Safety standards Applied CE MarkingWaste Electrical and Electric Equipment Weee Label MaterialSRP-275 Introduction Front viewRear view SRP-275 Table of Contents SRP-275 Setting Up the Printer UnpackingChoosing a place for the printer Using the operation panel Control panel Power LED Green ColorError LED Red Color Paper OUT LED Red ColorSRP-275 Connecting the cables Connecting the AC AdaptorConnecting the Interface cable and Drawer kick-out cable Connect the AC adapter according to the following procedureInterface connector ConnectorSerial Interface RS-232C Drawer kick-outPin no Source Compatibility mode Nibble mode Byte mode Parallel Interface IEEE1284USB Interface Ethernet InterfaceDrawer kick-out Pin No Description DirectionSRP-275 Setting the Switches Setting the DIP SwitchDIP Switch setting for EpsonESC/POS mode DIP Switch setting for CitizeniDP 3550 mode International Character Selection DSW Code CountryDIP Switch setting for StarSP500 mode Emulation Selection DSW 1-1Changing the DIP Switch setting Setting the Memory Switches Memory Switch setting for EpsonESC/POS modeMemory Switch Function OffCustomize value Function Selectable value Serial communication Function Selectable valueMemory Switch Setup Mode Example of Memory Switch setup sheetProcedure of Memory Switch setting Memory Switch setting for Star mode SettingsFunction Class Default Settings Function Memory Switch Bit DbcsMemory Switch Bit Function MSW 2-ACharacter Table *2 Memory Switch Bit Function Reserved SRP-275 Ribbon Cassette Installation SRP-275 Roll Paper Installation SRP-275 Changing the paper width SRP-275 Installing the wall mount Option SRP-275 Self Test To use the hexadecimal dump feature, follow these steps SRP-275 Hexadecimal DumpingHexadecimal dump Specification Printing specificationPaper specifications Ribbon cassette specificationElectrical characteristics ReliabilityEnvironment conditions Dimensions & weight Optional featuresDimensions WeightSRP-275 Appendix Troubleshooting Error LED blinking patternRecoverable errors Error Description Error LED blinking pattern RecoveryPrinter does not start printing If any of the lights are on, please check the followingPrinter stops printing You want to check the operation of the printer by itselfPrinting is poor Self test