Savin 7800W Setting a Leading Edge Margin, You can set a margin at the leading edge of the copy

Page 41

Setting a Leading Edge Margin

Setting a Leading Edge Margin

You can set a margin at the leading edge of the copy.

Leading Edge

Margin

Using the Copy Paper Table, or in the Preset Cut mode, Variable cut mode

Leading Edge Margin

In the Semi Synchro Cut mode

3

Note

❒You can set up to a ± 99mm, ± 4.0" margin in 1mm, 0.1" steps at the leading edge.

❒The copy image is shifted to the trailing edge, when you make a copy using the bypass table, or in the Preset Cut mode or Variable Cut mode.

❒In the Semi Synchro Cut mode, the paper length is increased by the leading margin width.

A Press the {Function Select} key until the Leading Edge indicator is lit.

B

C

Press the {+} key and {− } key to specify an edge margin. To zero the value, press the {Clear/Stop} key.

Insert the original from the leading edge.

You can get same results using the Rear Table.

31

Image 41

Contents Operating Instructions Means Power on Means Stand by Safety During Operation Safety InformationPage Iii Energy Star Program SpecificationSymbols How to Read this ManualTable of Contents Specifications Viii Copier Exterior Guide to ComponentsMain switch Operation Panel Function indicatorsClear/Stop key Turn Off the Main Power Turning on the PowerTurn On the Main Power Recommended Originals ⇒ P.17 Using the Rear TableNon-recommended Originals Recommended Paper Anti-humidity Heater Handling Toner TonerToner Storage Used TonerBasic Copying Copying to sheets CopyingMake sure that the Bypass Tray is selected Basic Copying Copying to sheets Copying Using the Roll Feeder Option Copying Using the Rear Table Copying Semi Synchro cutting Copying onto Roll Paper OptionPress the Cut Select key1 Copying onto Roll Paper Option Preset Cutting Variable Cutting Press the Preset Cut keyYou can change the settings by 1mm 0.1 steps Using The Roll Cutting Rail Option Copying Copying Onto Other Media Copy SettingsAdjusting the Fusing Temperature Manually Adjusting Copy Image Density Making Several Copies of the Same Original You can set a margin at the leading edge of the copy Setting a Leading Edge MarginPartial Copying P will stay on, not blinking Copier starts copying P will disappear Program key Programming Settings You Often UseRecalling Settings Stored in the Program key Changing the Default SettingTurn off the main switch Press the Function Select key User ToolsUser Tools Settings You Can Change with User Tools Settings You Can Change with User Tools This value can be changed to 1, 2, 3, or 10 intervals Semi-synchro Cut Length Adjustment+19 Adjust the cut length Standard Density 1 Darker Image Density Default Changing The Used Toner Bottle Maintaining Your CopierMaintaining Your Copier Close the upper unit Adding Toner Adding Toner Close the toner cartridge cover and the original table Adding Toner Removing the Roll Paper Holder Setting the Roll Paper HolderChanging The Roll Paper Size Changing The Roll Paper Size Loading a Roll Of Paper Insert the paper roll as far as it will go Maintaining Your Copier Hold the paper B , and then slide the cutter a Close the Roll Feeder Loading a New Roll Onto Paper Cutting Rail Option Maintaining Your Copier If Something Goes Wrong If Indicator Lights UpIf the Original is Jammed at the Exit If Jams OccurIf Sheet Paper is Jammed in the Feed-in Slot If Sheet Paper is Jammed at the Paper Exit If Roll Paper Jams Troubleshooting If You Cannot See the Roll Paper Jam Hold the paper B , and then slide the cutter a Close the Roll Feeder Absolutely nothing happens OthersIf Jams Occur Frequently If Copies Look WrongBlack streaks appear on copies CreasesCopies Come Out Dog Eared Clean the Exposure Glass & the Platen Plate Daily MaintenanceDos & Donts Machine Environment Where to Put Your CopierPower Connection Access To Machine Copier SpecificationsRoll feeder OptionsIndex