Savin 7700W, 7800W operating instructions Adding Toner

Page 58

Maintaining Your Copier

Adding Toner

When D is displayed, it is time to add toner.

When the indicator starts blinking, you can still copy about 53 feet of paper (16 m, 27 81/2"⋅ 11" size copies). When the indicator stays on, you can't copy until a new cartridge is installed.

RWARNING:

•Do not incinerate used toner, toner bottle or toner cartridge.

• Toner dust might ignite when exposed to an open flame.

•Dispose of the used toner and the used toner cartridge ac- cording to local regulations.

4 R CAUTION:

•Do not eat or swallow toner.

• Keep toner (used or unused), toner bottle, and toner cartridge out of reach of children.

RCAUTION:

•This machine has been tested for safety using this supplier's

parts and consumables. We recommend you only use these specified supplies.

Note

❒If you use toner other than that recommended, a fault might occur.

❒When adding toner, do not turn off the main switch. If you do, your settings will be cleared.

❒Always add toner after the machine instructs you to add toner.

❒Do not use used toner. This will damage the machine.

A Lift the original table until it locks in place.

Note

❒If your machine does not have roll feeder, pull down the Bypass Table first.

48

Image 58

Contents Operating Instructions Means Power on Means Stand by Safety Information Safety During OperationPage Iii Specification Energy Star ProgramHow to Read this Manual SymbolsTable of Contents Specifications Viii Guide to Components Copier ExteriorMain switch Function indicators Operation PanelClear/Stop key Turn On the Main Power Turning on the PowerTurn Off the Main Power ⇒ P.17 Using the Rear Table Recommended OriginalsNon-recommended Originals Recommended Paper Anti-humidity Heater Toner Storage TonerHandling Toner Used TonerCopying Basic Copying Copying to sheetsMake sure that the Bypass Tray is selected Basic Copying Copying to sheets Copying Using the Roll Feeder Option Copying Using the Rear Table Copying Copying onto Roll Paper Option Semi Synchro cuttingPress the Cut Select key1 Copying onto Roll Paper Option Preset Cutting Press the Preset Cut key Variable CuttingYou can change the settings by 1mm 0.1 steps Using The Roll Cutting Rail Option Copying Copy Settings Copying Onto Other MediaAdjusting the Fusing Temperature Manually Adjusting Copy Image Density Making Several Copies of the Same Original Setting a Leading Edge Margin You can set a margin at the leading edge of the copyPartial Copying P will stay on, not blinking Copier starts copying P will disappear Programming Settings You Often Use Program keyChanging the Default Setting Recalling Settings Stored in the Program keyTurn off the main switch User Tools Press the Function Select keyUser Tools Settings You Can Change with User Tools Settings You Can Change with User Tools This value can be changed to 1, 2, 3, or 10 intervals Semi-synchro Cut Length Adjustment+19 Adjust the cut length Standard Density 1 Darker Image Density Default Maintaining Your Copier Changing The Used Toner BottleMaintaining Your Copier Close the upper unit Adding Toner Adding Toner Close the toner cartridge cover and the original table Adding Toner Changing The Roll Paper Size Setting the Roll Paper HolderRemoving the Roll Paper Holder Changing The Roll Paper Size Loading a Roll Of Paper Insert the paper roll as far as it will go Maintaining Your Copier Hold the paper B , and then slide the cutter a Close the Roll Feeder Loading a New Roll Onto Paper Cutting Rail Option Maintaining Your Copier If Indicator Lights Up If Something Goes WrongIf Jams Occur If the Original is Jammed at the ExitIf Sheet Paper is Jammed in the Feed-in Slot If Sheet Paper is Jammed at the Paper Exit If Roll Paper Jams Troubleshooting If You Cannot See the Roll Paper Jam Hold the paper B , and then slide the cutter a Close the Roll Feeder If Jams Occur Frequently OthersAbsolutely nothing happens If Copies Look WrongCopies Come Out Dog Eared CreasesBlack streaks appear on copies Daily Maintenance Clean the Exposure Glass & the Platen PlateDos & Donts Where to Put Your Copier Machine EnvironmentPower Connection Access To Machine Specifications CopierOptions Roll feederIndex