Savin 7800W, 7700W operating instructions Dos & Donts

Page 83

Do's & Don'ts

Do's & Don'ts

RCAUTION:

•When you move the machine, unplug the power cord from the wall outlet to avoid fire or electric shock.

•When the machine will not be used for a long time, unplug the power cord.

•Do not touch areas on or around the fusing unit. These areas get hot.

•After copies are made continuously, the exposure glass may feel warm. This is not a malfunction.

•The area around the ventilation hole may feel warm. This is caused by ex- haust air and is not a malfunction.

•Do not turn off the main switch while copying. Before turning off the main switch, make sure that copying is completed.

• The machine might fail to produce good copy images if there is condensation	5
inside caused by a temperature change.

•Do not open the covers of the machine while copying. If you do, misfeeds might occur.

•Do not move the machine while copying.

•The supplier shall not be liable for any loss or damage resulting from a failure of the machine, a loss of machine settings, or use of the machine.

•Do not place more than one sheet of paper at a time on the bypass table.

•Center your paper on the copy table using the size marks. Then slide the pa- per straight into the copier until it stops.

•When copying to a long sheet of paper, lightly hold the sheet as the copier pulls it in so that it goes in well.

•Do not make two sided copies.

•If you open the unit, make sure you close it within 5 minutes to keep light from damaging the copy drum.

•When copying to sheets 35" ⋅ 45" (90 cm ⋅ 115 cm) or larger, make sure the pa- per does not drag directly on the floor as the copier pulls it in. (You can spread paper on the floor for this.)

•If your paper has an uneven or slanted edge, do not insert this edge in first.

•Do not make copies longer than 80 inches (2 m).

•Do not insert originals made of paper less the 52.3 g/m2 (13.9 lb or 0.07 mm thick). For such originals, please use the optional Carrier Sheet.

73

Image 83

Contents Operating Instructions Means Power on Means Stand by Safety During Operation Safety InformationPage Iii Energy Star Program SpecificationSymbols How to Read this ManualTable of Contents Specifications Viii Copier Exterior Guide to ComponentsMain switch Operation Panel Function indicatorsClear/Stop key Turn Off the Main Power Turning on the PowerTurn On the Main Power Recommended Originals ⇒ P.17 Using the Rear TableNon-recommended Originals Recommended Paper Anti-humidity Heater Used Toner TonerHandling Toner Toner StorageBasic Copying Copying to sheets CopyingMake sure that the Bypass Tray is selected Basic Copying Copying to sheets Copying Using the Roll Feeder Option Copying Using the Rear Table Copying Semi Synchro cutting Copying onto Roll Paper OptionPress the Cut Select key1 Copying onto Roll Paper Option Preset Cutting Variable Cutting Press the Preset Cut keyYou can change the settings by 1mm 0.1 steps Using The Roll Cutting Rail Option Copying Copying Onto Other Media Copy SettingsAdjusting the Fusing Temperature Manually Adjusting Copy Image Density Making Several Copies of the Same Original You can set a margin at the leading edge of the copy Setting a Leading Edge MarginPartial Copying P will stay on, not blinking Copier starts copying P will disappear Program key Programming Settings You Often UseRecalling Settings Stored in the Program key Changing the Default SettingTurn off the main switch Press the Function Select key User ToolsUser Tools Settings You Can Change with User Tools Settings You Can Change with User Tools This value can be changed to 1, 2, 3, or 10 intervals Semi-synchro Cut Length Adjustment+19 Adjust the cut length Standard Density 1 Darker Image Density Default Changing The Used Toner Bottle Maintaining Your CopierMaintaining Your Copier Close the upper unit Adding Toner Adding Toner Close the toner cartridge cover and the original table Adding Toner Removing the Roll Paper Holder Setting the Roll Paper HolderChanging The Roll Paper Size Changing The Roll Paper Size Loading a Roll Of Paper Insert the paper roll as far as it will go Maintaining Your Copier Hold the paper B , and then slide the cutter a Close the Roll Feeder Loading a New Roll Onto Paper Cutting Rail Option Maintaining Your Copier If Something Goes Wrong If Indicator Lights UpIf the Original is Jammed at the Exit If Jams OccurIf Sheet Paper is Jammed in the Feed-in Slot If Sheet Paper is Jammed at the Paper Exit If Roll Paper Jams Troubleshooting If You Cannot See the Roll Paper Jam Hold the paper B , and then slide the cutter a Close the Roll Feeder If Copies Look Wrong OthersAbsolutely nothing happens If Jams Occur FrequentlyBlack streaks appear on copies CreasesCopies Come Out Dog Eared Clean the Exposure Glass & the Platen Plate Daily MaintenanceDos & Donts Machine Environment Where to Put Your CopierPower Connection Access To Machine Copier SpecificationsRoll feeder OptionsIndex