Savin 7700W, 7800W operating instructions Settings You Can Change with User Tools

Page 50

Copy Settings

Settings You Can Change with User Tools

This section is for the key operators in charge of this machine. You can change or set the machine's default settings.

Note

❒For how to enter the User Tools program, press the {Clear Modes/Energy Saver} key, and then press the {Clear/Stop} key for more than 3 seconds.

3

•Fusing Temperature 1–Normal(+01): Selects the fusing temperature for plain paper.

Note

❒0: Mode 1, 1: Mode 2, 2: Mode 3, 3: Mode 4, 4: Mode 5, 5: Mode 6, 6: Mode 7

❒Default: 2

❒For details about each mode, contact your service representative.

•Fusing Temperature 2–High (+02): Selects the fusing temperature for trans- lucent paper.

Note

❒0: Mode 5, 1: Mode 6, 2: Mode 7, 3: Mode 8

❒Default: 0

❒For details about each mode, contact your service representative.

•Fusing Temperature 3–Low(+03): Selects the fusing temperature for translu- cent film.

Note

❒0: Mode 2, 1: Mode 3, 2: Mode 4, 3: Mode 5

❒Default: 1

❒For details about each mode, contact your service representative.

•Count Up/Down(+04): The copy counter can be made to count up or count down.

Note

❒0: Count up, 1: Count down

40

Image 50

Contents Operating Instructions Means Power on Means Stand by Safety Information Safety During OperationPage Iii Specification Energy Star ProgramHow to Read this Manual SymbolsTable of Contents Specifications Viii Guide to Components Copier ExteriorMain switch Function indicators Operation PanelClear/Stop key Turn Off the Main Power Turning on the PowerTurn On the Main Power ⇒ P.17 Using the Rear Table Recommended OriginalsNon-recommended Originals Recommended Paper Anti-humidity Heater Toner Storage TonerHandling Toner Used TonerCopying Basic Copying Copying to sheetsMake sure that the Bypass Tray is selected Basic Copying Copying to sheets Copying Using the Roll Feeder Option Copying Using the Rear Table Copying Copying onto Roll Paper Option Semi Synchro cuttingPress the Cut Select key1 Copying onto Roll Paper Option Preset Cutting Press the Preset Cut key Variable CuttingYou can change the settings by 1mm 0.1 steps Using The Roll Cutting Rail Option Copying Copy Settings Copying Onto Other MediaAdjusting the Fusing Temperature Manually Adjusting Copy Image Density Making Several Copies of the Same Original Setting a Leading Edge Margin You can set a margin at the leading edge of the copyPartial Copying P will stay on, not blinking Copier starts copying P will disappear Programming Settings You Often Use Program keyChanging the Default Setting Recalling Settings Stored in the Program keyTurn off the main switch User Tools Press the Function Select keyUser Tools Settings You Can Change with User Tools Settings You Can Change with User Tools This value can be changed to 1, 2, 3, or 10 intervals Semi-synchro Cut Length Adjustment+19 Adjust the cut length Standard Density 1 Darker Image Density Default Maintaining Your Copier Changing The Used Toner BottleMaintaining Your Copier Close the upper unit Adding Toner Adding Toner Close the toner cartridge cover and the original table Adding Toner Removing the Roll Paper Holder Setting the Roll Paper HolderChanging The Roll Paper Size Changing The Roll Paper Size Loading a Roll Of Paper Insert the paper roll as far as it will go Maintaining Your Copier Hold the paper B , and then slide the cutter a Close the Roll Feeder Loading a New Roll Onto Paper Cutting Rail Option Maintaining Your Copier If Indicator Lights Up If Something Goes WrongIf Jams Occur If the Original is Jammed at the ExitIf Sheet Paper is Jammed in the Feed-in Slot If Sheet Paper is Jammed at the Paper Exit If Roll Paper Jams Troubleshooting If You Cannot See the Roll Paper Jam Hold the paper B , and then slide the cutter a Close the Roll Feeder If Jams Occur Frequently OthersAbsolutely nothing happens If Copies Look WrongBlack streaks appear on copies CreasesCopies Come Out Dog Eared Daily Maintenance Clean the Exposure Glass & the Platen PlateDos & Donts Where to Put Your Copier Machine EnvironmentPower Connection Access To Machine Specifications CopierOptions Roll feederIndex