Savin 7700W, 7800W operating instructions Where to Put Your Copier, Machine Environment

Page 84

Troubleshooting

Where to Put Your Copier

Your copier should be installed by a qualified technician. If you need to trans- port your copier to a distant location, call your service center before the move.

You can of course move your copier around your office without calling the serv- ice center. If you do, remember that the temperature, humidity, and cleanliness of the area around the copier may affect its performance. Choose the new loca- tion with care and follow the guidelines below.

Machine Environment

Your machine's location should be carefully chosen because environmental con- ditions greatly affect its performance.

Optimal Environmental Conditions

5

R CAUTION:

• Keep the machine away from humidity and dust. A fire or an elec- tric shock might occur.

• Do not place the machine on an unstable or tilted surface. If it top- ples over, it could cause injury.

RCAUTION:

•If you use the machine in a confined space, make sure there is a continuous air turnover.

•Temperature: 50° to 86°F (15° to 30°C)

•Humidity: 20 to 80% RH

•To avoid possible ozone build-up make sure to install this copier in a large, well ventilated room ensuring an air turnover of at least 1000 ft3/hour/per- son (30 m3). When you use this machine for a long time in a confined space without good ventilation, you may notice an odd smell. To keep the work- space comfortable, we recommend that you keep it well ventilated.

•Set your copier on a strong and level base. The copier must be level within a quarter of an inch (5 mm) left to right and half an inch (10 mm) front to rear.

Environments to Avoid

•Locations exposed to direct sunlight or strong light (more than 1500 lux)

•Dusty areas

•Areas with corrosive gasses

•Altitudes of over 6500 feet (2000 m)

74

Image 84

Contents Operating Instructions Means Power on Means Stand by Safety Information Safety During OperationPage Iii Specification Energy Star ProgramHow to Read this Manual SymbolsTable of Contents Specifications Viii Guide to Components Copier ExteriorMain switch Function indicators Operation PanelClear/Stop key Turning on the Power Turn On the Main PowerTurn Off the Main Power ⇒ P.17 Using the Rear Table Recommended OriginalsNon-recommended Originals Recommended Paper Anti-humidity Heater Toner Handling TonerToner Storage Used TonerCopying Basic Copying Copying to sheetsMake sure that the Bypass Tray is selected Basic Copying Copying to sheets Copying Using the Roll Feeder Option Copying Using the Rear Table Copying Copying onto Roll Paper Option Semi Synchro cuttingPress the Cut Select key1 Copying onto Roll Paper Option Preset Cutting Press the Preset Cut key Variable CuttingYou can change the settings by 1mm 0.1 steps Using The Roll Cutting Rail Option Copying Copy Settings Copying Onto Other MediaAdjusting the Fusing Temperature Manually Adjusting Copy Image Density Making Several Copies of the Same Original Setting a Leading Edge Margin You can set a margin at the leading edge of the copyPartial Copying P will stay on, not blinking Copier starts copying P will disappear Programming Settings You Often Use Program keyChanging the Default Setting Recalling Settings Stored in the Program keyTurn off the main switch User Tools Press the Function Select keyUser Tools Settings You Can Change with User Tools Settings You Can Change with User Tools This value can be changed to 1, 2, 3, or 10 intervals Semi-synchro Cut Length Adjustment+19 Adjust the cut length Standard Density 1 Darker Image Density Default Maintaining Your Copier Changing The Used Toner BottleMaintaining Your Copier Close the upper unit Adding Toner Adding Toner Close the toner cartridge cover and the original table Adding Toner Setting the Roll Paper Holder Changing The Roll Paper SizeRemoving the Roll Paper Holder Changing The Roll Paper Size Loading a Roll Of Paper Insert the paper roll as far as it will go Maintaining Your Copier Hold the paper B , and then slide the cutter a Close the Roll Feeder Loading a New Roll Onto Paper Cutting Rail Option Maintaining Your Copier If Indicator Lights Up If Something Goes WrongIf Jams Occur If the Original is Jammed at the ExitIf Sheet Paper is Jammed in the Feed-in Slot If Sheet Paper is Jammed at the Paper Exit If Roll Paper Jams Troubleshooting If You Cannot See the Roll Paper Jam Hold the paper B , and then slide the cutter a Close the Roll Feeder Others Absolutely nothing happensIf Jams Occur Frequently If Copies Look WrongCreases Copies Come Out Dog EaredBlack streaks appear on copies Daily Maintenance Clean the Exposure Glass & the Platen PlateDos & Donts Where to Put Your Copier Machine EnvironmentPower Connection Access To Machine Specifications CopierOptions Roll feederIndex