Savin 7700W, 7800W operating instructions Recommended Paper

Page 18

Basics

Recommended Paper

• Standard paper sizes that can be used in this copier are shown below.


1		Metric version	Inch version	Bypass	Roll Feeder

		A0	E (36"⋅ 48")	K	K

		A1	D (24"⋅ 36")	KL	KL

		A2	C (18"⋅ 24")	KL	KL

		A3	B (12"⋅ 18")	KL	KL

		A4	A (9"⋅ 12")	K	K

•When you make a copy on a non-standard size of paper, set the paper on the Copy Paper Table.

•Weight of paper suitable for this copier: 51g/m2, 14lb to 134g/m2, 36lb.

•Do not use the following kinds of paper or a paper jam might occur.

•Bent, folded, or creased paper

•Torn paper

•Perforated paper

•Non-smooth paper

•Slippery paper

•Thin paper that has low stiffness

•Do not make a copy on paper with any kind of coating, such as thermosensi- tive paper, art paper, aluminum foil, and carbon paper.

A fault might occur.

•Do not use paper with strong curls at the edges or corners. (Curls rising more than 5mm (1/4") or falling more than 20mm (3/4") over a 40mm (1.5") radius.)

•When you make copies on film, take out the copies delivered to the copy guide one sheet at a time and place them on a flat surface.

•If copying to natural tracing paper (all pulp, translucent paper) at a relative humidity of 35% or less

A If the paper was left out of its package for 5 minutes or more, remove the first 1000mm (39.3") before copying.

B If copies come out wavy or with white spots, use translucent paper instead of natural tracing paper.

C Always keep the paper in a bag when not using it.

•Store the paper in a sealed polyvinyl bag if not used for a long period.

If it gets humid, paper will curl or wave which can cause a paper jam or part of the image not to be copied.

8

Image 18

Contents Operating Instructions Means Power on Means Stand by Safety Information Safety During OperationPage Iii Specification Energy Star ProgramHow to Read this Manual SymbolsTable of Contents Specifications Viii Guide to Components Copier ExteriorMain switch Function indicators Operation PanelClear/Stop key Turning on the Power Turn On the Main PowerTurn Off the Main Power ⇒ P.17 Using the Rear Table Recommended OriginalsNon-recommended Originals Recommended Paper Anti-humidity Heater Toner Storage TonerHandling Toner Used TonerCopying Basic Copying Copying to sheetsMake sure that the Bypass Tray is selected Basic Copying Copying to sheets Copying Using the Roll Feeder Option Copying Using the Rear Table Copying Copying onto Roll Paper Option Semi Synchro cuttingPress the Cut Select key1 Copying onto Roll Paper Option Preset Cutting Press the Preset Cut key Variable CuttingYou can change the settings by 1mm 0.1 steps Using The Roll Cutting Rail Option Copying Copy Settings Copying Onto Other MediaAdjusting the Fusing Temperature Manually Adjusting Copy Image Density Making Several Copies of the Same Original Setting a Leading Edge Margin You can set a margin at the leading edge of the copyPartial Copying P will stay on, not blinking Copier starts copying P will disappear Programming Settings You Often Use Program keyChanging the Default Setting Recalling Settings Stored in the Program keyTurn off the main switch User Tools Press the Function Select keyUser Tools Settings You Can Change with User Tools Settings You Can Change with User Tools This value can be changed to 1, 2, 3, or 10 intervals Semi-synchro Cut Length Adjustment+19 Adjust the cut length Standard Density 1 Darker Image Density Default Maintaining Your Copier Changing The Used Toner BottleMaintaining Your Copier Close the upper unit Adding Toner Adding Toner Close the toner cartridge cover and the original table Adding Toner Setting the Roll Paper Holder Changing The Roll Paper SizeRemoving the Roll Paper Holder Changing The Roll Paper Size Loading a Roll Of Paper Insert the paper roll as far as it will go Maintaining Your Copier Hold the paper B , and then slide the cutter a Close the Roll Feeder Loading a New Roll Onto Paper Cutting Rail Option Maintaining Your Copier If Indicator Lights Up If Something Goes WrongIf Jams Occur If the Original is Jammed at the ExitIf Sheet Paper is Jammed in the Feed-in Slot If Sheet Paper is Jammed at the Paper Exit If Roll Paper Jams Troubleshooting If You Cannot See the Roll Paper Jam Hold the paper B , and then slide the cutter a Close the Roll Feeder If Jams Occur Frequently OthersAbsolutely nothing happens If Copies Look WrongCreases Copies Come Out Dog EaredBlack streaks appear on copies Daily Maintenance Clean the Exposure Glass & the Platen PlateDos & Donts Where to Put Your Copier Machine EnvironmentPower Connection Access To Machine Specifications CopierOptions Roll feederIndex