Savin 7800W, 7700W operating instructions Settings You Can Change with User Tools

Page 51

Settings You Can Change with User Tools

❒Default: 0

•Beeper On/Off(+05): The beeper can be turned off completely; turned off for setting the margin, multiple copies, and paper length; or left on to emit a tone whenever a key is pressed.

Note

❒0: On, 1: All Off, 2: Partially Off

❒Default: 2(The beeper does not work if you use leading edge margin.)

•Paper Feed Out Waiting Time Setting(+06): When the copier is ready to re- ceive the original, it will wait for a preset length of time. If no original is set

	within this time, the copier will process the copy paper without copying. The
		3
	time can be set to 1, 2, 3, 4, or 5 minutes.

Note

❒0: 2min, 1: 1min, 2: 3min, 3: 4min, 4: 5 min

❒Default: 0

•Manual Feed Start Time Setting(+07): After the copy paper is set, the copier waits for a preset number of seconds before starting the rollers that will pull the paper in. This pause gives you a chance to align the paper. The time can be set to 0.7, 1, 2, 3, 4, or 5 seconds.

Note

❒0: 2.0sec, 1: 0.7sec, 2: 1.0sec, 3: 3.0sec, 4: 4.0sec, 5: 5.0sec

❒Default: 0

•Lead Edge Increase/Decrease Speed Setting(+08): The speed at which the lead edge setting scrolls up or down can be changed. The time for one incre- ment (or decrement) can be set to 0.02, 0.05, 0.10, 0.25, or 0.5 seconds.

Note

❒0: 0.10 sec, 1: 0.50 sec, 2: 0.25 sec, 3: 0.05 sec, 4: 0.02 sec

❒Default: 0

•Auto Reset Time Setting(+09): If the copier is idle for a while, it will clear it- self. The time needed can be set to 1, 2, 3, 4, or 5 minutes. This function can also be turned off.

Note

❒0: 2 min, 1: 1min, 2: 3 min, 3: 4 min, 4: 5 min, 5: None

❒Default: 0

❒The machine cannot enter the Auto reset mode if the roll end indicator lights while copying repeatedly.

❒The machine cannot enter the Auto clear if the toner end indicator lights.

41

Image 51

Contents Operating Instructions Means Power on Means Stand by Safety During Operation Safety InformationPage Iii Energy Star Program SpecificationSymbols How to Read this ManualTable of Contents Specifications Viii Copier Exterior Guide to ComponentsMain switch Operation Panel Function indicatorsClear/Stop key Turning on the Power Turn On the Main PowerTurn Off the Main Power Recommended Originals ⇒ P.17 Using the Rear TableNon-recommended Originals Recommended Paper Anti-humidity Heater Used Toner TonerHandling Toner Toner StorageBasic Copying Copying to sheets CopyingMake sure that the Bypass Tray is selected Basic Copying Copying to sheets Copying Using the Roll Feeder Option Copying Using the Rear Table Copying Semi Synchro cutting Copying onto Roll Paper OptionPress the Cut Select key1 Copying onto Roll Paper Option Preset Cutting Variable Cutting Press the Preset Cut keyYou can change the settings by 1mm 0.1 steps Using The Roll Cutting Rail Option Copying Copying Onto Other Media Copy SettingsAdjusting the Fusing Temperature Manually Adjusting Copy Image Density Making Several Copies of the Same Original You can set a margin at the leading edge of the copy Setting a Leading Edge MarginPartial Copying P will stay on, not blinking Copier starts copying P will disappear Program key Programming Settings You Often UseRecalling Settings Stored in the Program key Changing the Default SettingTurn off the main switch Press the Function Select key User ToolsUser Tools Settings You Can Change with User Tools Settings You Can Change with User Tools This value can be changed to 1, 2, 3, or 10 intervals Semi-synchro Cut Length Adjustment+19 Adjust the cut length Standard Density 1 Darker Image Density Default Changing The Used Toner Bottle Maintaining Your CopierMaintaining Your Copier Close the upper unit Adding Toner Adding Toner Close the toner cartridge cover and the original table Adding Toner Setting the Roll Paper Holder Changing The Roll Paper SizeRemoving the Roll Paper Holder Changing The Roll Paper Size Loading a Roll Of Paper Insert the paper roll as far as it will go Maintaining Your Copier Hold the paper B , and then slide the cutter a Close the Roll Feeder Loading a New Roll Onto Paper Cutting Rail Option Maintaining Your Copier If Something Goes Wrong If Indicator Lights UpIf the Original is Jammed at the Exit If Jams OccurIf Sheet Paper is Jammed in the Feed-in Slot If Sheet Paper is Jammed at the Paper Exit If Roll Paper Jams Troubleshooting If You Cannot See the Roll Paper Jam Hold the paper B , and then slide the cutter a Close the Roll Feeder If Copies Look Wrong OthersAbsolutely nothing happens If Jams Occur FrequentlyCreases Copies Come Out Dog EaredBlack streaks appear on copies Clean the Exposure Glass & the Platen Plate Daily MaintenanceDos & Donts Machine Environment Where to Put Your CopierPower Connection Access To Machine Copier SpecificationsRoll feeder OptionsIndex