Savin 7800W, 7700W operating instructions Adjusting Copy Image Density

Page 39

Adjusting Copy Image Density

Adjusting Copy Image Density

To make copies darker or lighter, change the density setting. There are 14 densi- ty levels (=7 notches ⋅ 2).

•Standard density level (Default)

•3 darker levels

•10 lighter levels

Set the density with the {i} and {j} keys under the density indicator.

Note

3

❒The indicator shows seven levels at a time. When you start from the standard image density, the middle notch corresponds to the standard image density, the three right notches correspond to darker densities, and the three left notches to lighter densities.

❒The brighter notch shows which level is now set. If you go lower than the left- most notch, the Lighter Copy indicator light up. The notches on the indicator correspond to the seven lightest levels.

❒If you change the copy image density while repeat copying, the next copy job will come out with new setting.

A Press the {i} or {j} key to adjust copy density.

B Each time you press the {i} key, the indicator moves one step to the left. When the indicator reaches the left edge, it returns to the right edge and the Lighter Copy indicator lights.

29

Image 39

Contents Operating Instructions Means Power on Means Stand by Safety During Operation Safety InformationPage Iii Energy Star Program SpecificationSymbols How to Read this ManualTable of Contents Specifications Viii Copier Exterior Guide to ComponentsMain switch Operation Panel Function indicatorsClear/Stop key Turning on the Power Turn On the Main PowerTurn Off the Main Power Recommended Originals ⇒ P.17 Using the Rear TableNon-recommended Originals Recommended Paper Anti-humidity Heater Used Toner TonerHandling Toner Toner StorageBasic Copying Copying to sheets CopyingMake sure that the Bypass Tray is selected Basic Copying Copying to sheets Copying Using the Roll Feeder Option Copying Using the Rear Table Copying Semi Synchro cutting Copying onto Roll Paper OptionPress the Cut Select key1 Copying onto Roll Paper Option Preset Cutting Variable Cutting Press the Preset Cut keyYou can change the settings by 1mm 0.1 steps Using The Roll Cutting Rail Option Copying Copying Onto Other Media Copy SettingsAdjusting the Fusing Temperature Manually Adjusting Copy Image Density Making Several Copies of the Same Original You can set a margin at the leading edge of the copy Setting a Leading Edge MarginPartial Copying P will stay on, not blinking Copier starts copying P will disappear Program key Programming Settings You Often UseRecalling Settings Stored in the Program key Changing the Default SettingTurn off the main switch Press the Function Select key User ToolsUser Tools Settings You Can Change with User Tools Settings You Can Change with User Tools This value can be changed to 1, 2, 3, or 10 intervals Semi-synchro Cut Length Adjustment+19 Adjust the cut length Standard Density 1 Darker Image Density Default Changing The Used Toner Bottle Maintaining Your CopierMaintaining Your Copier Close the upper unit Adding Toner Adding Toner Close the toner cartridge cover and the original table Adding Toner Setting the Roll Paper Holder Changing The Roll Paper SizeRemoving the Roll Paper Holder Changing The Roll Paper Size Loading a Roll Of Paper Insert the paper roll as far as it will go Maintaining Your Copier Hold the paper B , and then slide the cutter a Close the Roll Feeder Loading a New Roll Onto Paper Cutting Rail Option Maintaining Your Copier If Something Goes Wrong If Indicator Lights UpIf the Original is Jammed at the Exit If Jams OccurIf Sheet Paper is Jammed in the Feed-in Slot If Sheet Paper is Jammed at the Paper Exit If Roll Paper Jams Troubleshooting If You Cannot See the Roll Paper Jam Hold the paper B , and then slide the cutter a Close the Roll Feeder If Copies Look Wrong OthersAbsolutely nothing happens If Jams Occur FrequentlyCreases Copies Come Out Dog EaredBlack streaks appear on copies Clean the Exposure Glass & the Platen Plate Daily MaintenanceDos & Donts Machine Environment Where to Put Your CopierPower Connection Access To Machine Copier SpecificationsRoll feeder OptionsIndex