Savin 7800W, 7700W Semi-synchro Cut Length Adjustment+19 Adjust the cut length

Page 53

	Settings You Can Change with User Tools
•	Semi-synchro Cut Original Scanning Mode(+18): Selects whether the roll
	paper cut key must be pressed at the appropriate time when the trailing edge
	of the original passes the Semi-synchro cut mark, or whether the original
	must be inserted again after the original is scanned and the length is meas-
	ured.
	Note
	❒ 0: Pressing the roll paper cut key, 1: Inserting the original again
	❒ Default: 0
•	Semi-synchro Cut Length Adjustment(+19): Adjust the cut length in the
	semi-synchro cut mode.The setting can be changed from —25 to 25 by 1mm
			3
	steps.

Note

❒Default: 0

•Paper Length Up/Down Setting(+20): Select if the paper length is count down or up when the preset cut key is pressed.

Note

❒0: Down count, 1: Up count

❒Default: 0

•Paper Length Up/Down Speed Setting(+21) :The copier can scroll through the preset lengths forward or backward, and at different speeds. There are many sets of sizes from which to choose.

Note

❒0: 0.10 seconds, 1: 0.5 seconds, 2: 0.25 seconds, 3: 0.05 seconds, 4: 0.02 sec-

onds, 5: 0.01 seconds

❒Default: 0

•Fixed Paper Size Pattern Setting(+22): Select the fixed paper size pattern cho- sen when the “Preset Cut” key is press. For details about this setting, contact your service representative.

•Optional Paper Size Setting(+23 ~ +32): Up to 10 different paper size can be stored from 23 to 32.For details about this setting, contact your service repre- sentative.

•Auto Off Function setting(+33): This setting allows you to enable or disable the Auto Off function.

Note

❒0: Disable, 1: Enable

❒Default: 1

•Darker Image Density(+37): Sets the range of the ID density control to give finer control over darker images.

— ID level 1 to 7-Darker image density and low contrast settings —ID level 8 to 14-cannot be shifted

43

Image 53

Contents Operating Instructions Means Power on Means Stand by Safety During Operation Safety InformationPage Iii Energy Star Program SpecificationSymbols How to Read this ManualTable of Contents Specifications Viii Copier Exterior Guide to ComponentsMain switch Operation Panel Function indicatorsClear/Stop key Turn Off the Main Power Turning on the PowerTurn On the Main Power Recommended Originals ⇒ P.17 Using the Rear TableNon-recommended Originals Recommended Paper Anti-humidity Heater Handling Toner TonerToner Storage Used TonerBasic Copying Copying to sheets CopyingMake sure that the Bypass Tray is selected Basic Copying Copying to sheets Copying Using the Roll Feeder Option Copying Using the Rear Table Copying Semi Synchro cutting Copying onto Roll Paper OptionPress the Cut Select key1 Copying onto Roll Paper Option Preset Cutting Variable Cutting Press the Preset Cut keyYou can change the settings by 1mm 0.1 steps Using The Roll Cutting Rail Option Copying Copying Onto Other Media Copy SettingsAdjusting the Fusing Temperature Manually Adjusting Copy Image Density Making Several Copies of the Same Original You can set a margin at the leading edge of the copy Setting a Leading Edge MarginPartial Copying P will stay on, not blinking Copier starts copying P will disappear Program key Programming Settings You Often UseRecalling Settings Stored in the Program key Changing the Default SettingTurn off the main switch Press the Function Select key User ToolsUser Tools Settings You Can Change with User Tools Settings You Can Change with User Tools This value can be changed to 1, 2, 3, or 10 intervals Semi-synchro Cut Length Adjustment+19 Adjust the cut length Standard Density 1 Darker Image Density Default Changing The Used Toner Bottle Maintaining Your CopierMaintaining Your Copier Close the upper unit Adding Toner Adding Toner Close the toner cartridge cover and the original table Adding Toner Removing the Roll Paper Holder Setting the Roll Paper HolderChanging The Roll Paper Size Changing The Roll Paper Size Loading a Roll Of Paper Insert the paper roll as far as it will go Maintaining Your Copier Hold the paper B , and then slide the cutter a Close the Roll Feeder Loading a New Roll Onto Paper Cutting Rail Option Maintaining Your Copier If Something Goes Wrong If Indicator Lights UpIf the Original is Jammed at the Exit If Jams OccurIf Sheet Paper is Jammed in the Feed-in Slot If Sheet Paper is Jammed at the Paper Exit If Roll Paper Jams Troubleshooting If You Cannot See the Roll Paper Jam Hold the paper B , and then slide the cutter a Close the Roll Feeder Absolutely nothing happens OthersIf Jams Occur Frequently If Copies Look WrongBlack streaks appear on copies CreasesCopies Come Out Dog Eared Clean the Exposure Glass & the Platen Plate Daily MaintenanceDos & Donts Machine Environment Where to Put Your CopierPower Connection Access To Machine Copier SpecificationsRoll feeder OptionsIndex