Savin 3355, 3370 operating instructions Where Original Is Set Paper Size and Direction

Page 57

Copying

Note

❒See the following table for possible copy paper sizes and directions with Auto Paper Select (when copying at a ratio of 100%):

❖ Metric version

Where Original Is Set

Paper Size and Direction

Exposure glass

A3L, B4L, A4KL, B5KL, 81/2" ×

2

13"L *1

Document feeder

A3L, B4L, A4KL, B5KL, A5KL,

B6KL, 11" × 17"L, 81/2" × 11"KL, 81/

2" × 13"L *1 , 8KL, 16KKL

*1 You can select from 81/2" × 13", 81/4" × 13" and 8" × 13" with the User Tools (Sys-

tem Settings). See “<F/F4>Size Setting” in the System Settings manual.

❖ Inch version

Where Original Is Set

Paper Size and Direction

Exposure glass

11" × 17"L, 81/2" × 14"L, 81/2" ×

11"KL

Document feeder

A4

KL

, 11"

×

17"

L

, 11"

×

L

, 8

1

/2"

×

15"

14"L, 81/2" × 11"KL, 8" × 10"L, 10" ×

14"L, 51/2" × 81/2"KL, 81/2" × 13"L *1

*1 You can select from 81/2" × 13", 81/4" × 13" and 8" × 13" with the User Tools (Sys- tem Settings). See “<F/F4>Size Setting” in the System Settings manual.

❒For some originals, the original size might not be detected correctly. See ⇒ P.21 “Sizes difficult to detect”.

❒When you set special paper, such as recycled paper, in the paper tray, you can have the kind of paper shown on the display. See “Special Paper Indication” in the System Settings manual.

❒In Connect Copy mode, select the copy paper in the master unit.

•We recommend that both units have the same paper settings. Only paper trays loaded with the paper of the same size, direction and type installed in both the master unit and sub-unit are available.

•When you press the [Connect] key, only the paper trays that have the same settings in both units are displayed. Other trays are shown grayed out and cannot be selected.

•If the multiple trays are available in Connect Copy mode, each unit selects the paper tray detected in each “Paper Tray Priority” setting. See “Paper Tray Priority” in the System Settings manual.

•If the paper tray in use runs out of paper in the sub-unit, the paper tray that has the paper identical in size and different in direction is selected, and the original image is rotated (if “On (Rotate)” is selected in “Auto Tray Switch- ing”). See “Auto Tray Switching” in the System Settings manual.

44

Image 57

Contents 3355/3370 Page Means Power on Means Stand by Safety During Operation Safety InformationPage Symbols How to Read this ManualTable of Contents Preset Reduce/Enlarge Job PresetSort/Stack/Staple Punch Copying from the Bypass TrayFeatures and Benefits 210 Combination Chart 206Series/Book 137 Cover/Slip Sheet 151Connect Copy Display Panel 227 Using Connect Copy 230 What is Connect Copy? 223 How Connect Copy Works 225Printing Saved Documents 216 Deleting Saved Documents 220Dos And Donts 333 Where to Put Your Machine 334 Accessing the User Tools Copy/Document Server Features 305Changing the Paper Size 282 Adding Staples 285354 SpecificationPage Machine Types What You Can Do with This Machine Copy Mode Page Guide To Components ADF tray Connect Copy portBypass tray To copy onto normal paper and thick paper Output Tray GuideTo copy onto OHP transparencies and translucent paper Ventilation holeSheet Finisher OptionsLarge Capacity Tray LCT Booklet FinisherMain power indicator IndicatorsControl Panel Screen Contrast knobFunction Status indicator Function indicatorsStart key Number keysDisplay Panel Displays and Key OperationsInitial copy display Function menu Document Server initial display Function List Based on Options Duplex Combine Option *3 Page Turning On the Main Power Turning On the PowerOperation switch right side of the control panel Main power switch left side of the machineTurning Off the Main Power Starting the MachineShutting Down the Machine Metric version OriginalsInch version Non-recommended originals for the document feederSizes Detectable by the Auto Paper Select Missing Image Area Sizes difficult to detectExposure glass Document feeder Recommended Paper Sizes and Types Copy PaperB5KL, A5KL Non-recommended Paper Paper Storage Toner Toner StorageUsed Toner Basics Make sure that the machine is in Copy mode Basic ProcedureMake sure that there are no previous settings remaining Set your originalsPress the Start key Auto ResetSetting Originals Setting Originals on the Exposure GlassLift the document feeder Lower the document feeder Setting Originals in the Document FeederOriginal Orientation Standard OrientationTurn Make sure that the Standard Orientation key is selected Select the original orientationPress the 90 Turn key Press the OK key Batch Sadf mode Setting Special OriginalsMixed Sizes mode X14 11X17 Press the Thin key Press the OK key Thin modeBasic Functions Adjusting Copy Image DensityMake sure that the Auto Image Density key is selected Select one of Image Density modesSelecting Original Type Setting Auto Paper Select Selecting Copy PaperManual Paper Select Press the appropriate key to select the original typeWhere Original Is Set Paper Size and Direction Make sure that the Auto Paper Select key is selected Select the copy paperRotated copy Auto Reduce/Enlarge Where Original Is Set Original Size and DirectionCopying onto Tab Stock Select the paper trayTab sheet tray Preparation Pull out tray 2 until it stops Set originals Place the tab stocks in tray Make copiesSelect the paper tray tray Place your originals as follows Adjust the back fence as followsSort Sort/Stack/StapleStack optional finisher required Staple optional finisher requiredMaximum tray capacity is as follows Inch version Sort Rotate Sort Enter the number of copy sets with the number keys Stack StackSet the original, then press the Start key After all originals are scanned, press the #keySheet Finisher Booklet Finisher Staple 16KKL Except Sheet /100-Sheet Finisher Stapling position and original settingMetric version Inch version 2 × Stitch Select one of the stapling positions Press the Cancel key To Stop Scanning TemporarilyPress the Resume key to resume scanning To Remove the Paper from the Staple Unit When Memory Reaches 0%