Uniden BCT-8 manual Programming a Hybrid System

Page 49

The next available block appears on the display.

6. Repeat step 5 until you have selected a size code for each block.

For details about each size code, see "Fleet Map Size Codes" in the Appendix.

Programming a Hybrid System

A Hybrid system is simply a Type I system with some blocks designated as Type II blocks. To program a Hybrid system, follow the steps listed in "Programming a User Fleet Map" in

the previous section. However, if you want a block to be Type II, select Size Code . When you begin searching a trunking bank with a Hybrid Fleet Map, you will see both types of system IDs. That is, Type II IDs usually appear as an even number without a dash; Type I IDs appear as a three or four digit number, followed by a hyphen, followed by a one or two digit number.

Setting the Base, Spacing Frequencies and Offset Channel for Motorola VHF/UHF Trunked Systems

To properly track Motorola VHF and UHF trunked systems, you must enter what is known as the Base, Spacing Frequencies and Offset Channels for each system.

To find these out, check the scanner.uniden.com or www.trunktracker.com and other web sites and frequency resources.

To enter the Base, Spacing Frequencies and Offset Channel: (You can set up to three sets of these, but almost all systems only use one set)

1. Press and hold TRUNK for 1.5 seconds and select the bank you want to change.

2.

Use the ▲ or ▼ key to select

(Motorola Type2 VHF) or

 

 

 

 

(Motorola Type2

 

UHF), then press E.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.

Use the ▲ or ▼ key to select

, then press E.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4.

Use the keypad to enter Configuration Block Number(1-3).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5.

Use the keypad to enter a new Base Frequency, then press

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

E.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6.

Press the ▲ key and select

for entering the Spacing

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Frequency.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7.

Use the keypad to enter a new Spacing Frequency, then

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

press E.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Note: You can only enter within a range of 5-100 kHz, and 5 or 12.5 kHz multiples.

8. Press the ▲ key and select

for entering the Offset

Channel.

 

45

Page 48 Page 50
Image 49
Page 48 Page 50
Contents Page Precautions Contents Page LTR Introduction8 9 Front and Rear ViewsIcon Display What is Searching? What is Scanning?What is Trunk Tracking? TerminologyPage Feature Highlights Information on the Internet Where to Obtain More InformationScanner.uniden.com Included with Your Scanner Package Optional AccessoriesFor Home Use Desktop Installation Installing the BCT8For Mobile Use In-Car Installation Connecting the Power Cord Installation for everyday use Typical Mounting Methods Attach the scanner to the mounting bracket usingMounting the Scanner in Your Vehicle Supplied mounting knobsDC power Installation Applying Power for Vehicle InstallationConnecting an External Speaker Applying Power Using Standard AC PowerConnecting the Clone Cable Listening SafelyTurn the Scanner On Scanning OverviewHow Squelch Works Setting the SquelchSelecting the State Highway Patrol ScanningScanning Highway Patrol Frequency Highway Patrol Scan Hold Alert Tone VolumeHighway Warning Alert Muting the Alert ToneSkip Frequencies Alert Light AdjustmentPriority Channels Florida Trunked Highway Frequency Programming Frequencies into Channels Private Bank ScanningDeleting a Stored Frequency Memory Lock Duplicate Frequency AlertScanning Private Bank Hold/Resume Restoring a Locked-out Channel in Hold ModeChannel Lockout Priority Scan Restoring All Locked-out ChannelsChanging the Priority Channel Service Scanning Band Search Setting a Search BandData Skip Search Hold FeatureFrequency Skip Storing Search Frequencies DelayTrunk Tracking Selecting Trunking System Type Programming Trunking FrequenciesProgramming Talk Group ID/Scan Lists Programming Trunking FrequenciesTo enter a Type 1 ID To enter a Type 2 Talk Group IDTo enter a Full Edacs ID To enter a Partial Edacs IDReceiving Trunked Systems ID Scan ModeID Search Mode ID Scan Hold FeatureTo directly access a specific ID location ID Search Hold and Direct Entry ID in Hold Mode ID Monitor ModeProgramming Scan Lists During Search Deleting a Stored IDTo restore all locked out IDs in a bank once To restore a single ID, follow these stepsID Lockout Review ID LockoutSetting Priority in Trunking Mode Setting the Delay Mode for Trunking ModeTrunking Frequency Confirmation Moving between Scan List MemoriesMulti-Track Operational Details Multi-TrackEdacs Tracking Edacs ReceptionProgramming Edacs System Frequencies An Edacs Trunked system Edacs ID Range Search Special Edacs FeaturesLTR Tracking LTR ReceptionMotorola Tracking Motorola ReceptionFleet Map Programming Selecting Preset Fleet MapProgramming a User Fleet Map Programming a Hybrid System Toggling the Status Bit Control Channel Only ModeDisconnect Tone Detect Option End Code Remote Interface PC Control ModeTo connect Scanner to PC To program your scannerStart Remote Mode and Change Transfer Speed Clone ModeScanner.uniden.com PC Control Parameter To connect the Scanner to Scanner If you wish to clone another scanner right away General Use Care and MaintenanceNot receiving alarms Check antenna connections TroubleshootingAdjust the squelch for Trunking mode refer to Specifications State Code Order AppendixPreset Fleet Maps E1P9 Block Type I Programming Information User Defined Fleet MapsFleet Map Size Codes Memo Memo Uniden America Corporation One Year Limited Warranty

BCT-8 specifications

The Uniden BCT-8 is a portable scanner that has made a significant impact in the world of communications monitoring. Designed for both amateur enthusiasts and professional users, this device provides a robust set of features, making it an essential tool for anyone interested in receiving and decoding a wide range of radio frequencies.

One of the standout features of the BCT-8 is its ability to scan both conventional and trunked radio systems. This versatility allows users to listen to everything from local police and fire department communications to amateur radio operations and even aviation channels. The scanner operates between 25 MHz and 1300 MHz, covering a wide array of frequencies that cater to diverse listening interests.

The BCT-8 is equipped with a user-friendly interface, featuring an LCD screen that displays clearly readable information such as channel frequencies and descriptions. Additionally, it utilizes a programmable scan feature, enabling users to store frequencies in memory for quick access. This functionality is particularly useful for those who regularly monitor specific channels, saving time and simplifying the scanning process.

Another notable technology in the BCT-8 is its capability to decode CTCSS and DCS tones, allowing users to filter out unwanted signals and focus on the conversations that matter most to them. This feature is particularly beneficial for monitoring crowded frequencies, ensuring that listeners can hone in on their desired transmissions without interference.

The battery life of the Uniden BCT-8 is also impressive, providing extended use for those on the go. It can operate on AA batteries or a rechargeable battery pack, giving users flexibility depending on their listening habits and requirements.

In terms of build quality, the BCT-8 is sturdy yet compact, making it portable enough to carry during outdoor activities or while traveling. This is complemented by an included belt clip, allowing for hands-free operations, perfect for fieldwork or public safety applications.

Overall, the Uniden BCT-8 stands out for its extensive feature set and reliable performance, making it an ideal choice for individuals who wish to explore the rich world of radio communications. Its combination of advanced scanning capabilities, ease of use, and portability makes it a valuable addition to any scanner enthusiast's toolkit. Whether for personal use or professional monitoring, the BCT-8 excels in delivering comprehensive reception of diverse radio signals.
Top Page Image Contents