Uniden BCT-8 manual Programming Trunking Frequencies, Selecting Trunking System Type

Page 34

Programming Trunking Frequencies

There are three steps for programming a trunked system:

1.Program the Trunk Type – What type of system will the scanner be tracking, Motorola Type II, Type I, EDACS, LTR, etc.

2.Program the Trunked Frequencies – Within a trunked system, the frequencies are shared among all the users, called “Talk Groups”.

3.Program the Talk Groups – Within the trunked system, each agency or department is assigned a Talk Group ID. This ID must be programmed into the scanner in order for it to monitor that specific agency or department.

Before you start programming your scanner to track a trunked system, consider the following:

•You can only program one trunking system in each bank of your scanner.

•Trunked frequencies must be entered while in the Trunk Programming mode.

•If you’re in the Trunk Programming mode, you cannot select channels in other banks.

For example, if you are programming Bank 4, you can only select channels 151-200 with the ▲ or ▼ key.

•IMPORTANT: If you are programming an EDACS ® trunked system, you must enter the frequencies in a specific order. Check the frequency guide included with the radio and the listed web sites for details.

STEP 1: Selecting Trunking System Type

The first step in a Trunk Tracking system is storing the frequencies in one of the five available banks in your scanner.

1.Press TRUNK for 1.5 seconds.

You will hear two beeps, and “BANK” and “TRUNK” will begin to flash on the display.

2.Select the bank you want to store the frequency by using the

keypad.

3.Select the system you want to track by using the ▲ or ▼ key, then press E.

List of trunking systems as follows:

E2-800 (Motorola Type II 800 MHz)

E2-Hi (Motorola Type II VHF 136-174 MHz) *

E2-UHF (Motorola Type II UHF 406-512 MHz) *

E1 (Motorola Type I and Hybrid) **

Ed (EDACS® Wide Band: 9600 band)***

Ed SCt (EDACS Scat)

Lt (LTR)

*Requires programming of a Base and Spacing frequency Offset channel (See page 45).

**Requires programming of a Fleet map (See page 44).

30

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Page Precautions Contents Page Introduction LTRFront and Rear Views 8 9Icon Display What is Trunk Tracking? What is Scanning?What is Searching? TerminologyPage Feature Highlights Information on the Internet Where to Obtain More InformationScanner.uniden.com Optional Accessories Included with Your Scanner PackageFor Home Use Desktop Installation Installing the BCT8For Mobile Use In-Car Installation Connecting the Power Cord Installation for everyday use Mounting the Scanner in Your Vehicle Attach the scanner to the mounting bracket usingTypical Mounting Methods Supplied mounting knobsApplying Power for Vehicle Installation DC power InstallationConnecting the Clone Cable Applying Power Using Standard AC PowerConnecting an External Speaker Listening SafelyScanning Overview Turn the Scanner OnSetting the Squelch How Squelch WorksSelecting the State Highway Patrol ScanningScanning Highway Patrol Frequency Highway Warning Alert Alert Tone VolumeHighway Patrol Scan Hold Muting the Alert ToneSkip Frequencies Alert Light AdjustmentPriority Channels Florida Trunked Highway Frequency Programming Frequencies into Channels Private Bank ScanningDeleting a Stored Frequency Memory Lock Duplicate Frequency AlertScanning Private Bank Hold/Resume Restoring a Locked-out Channel in Hold ModeChannel Lockout Priority Scan Restoring All Locked-out ChannelsChanging the Priority Channel Service Scanning Setting a Search Band Band SearchData Skip Search Hold FeatureFrequency Skip Delay Storing Search FrequenciesTrunk Tracking Programming Trunking Frequencies Selecting Trunking System TypeProgramming Trunking Frequencies Programming Talk Group ID/Scan ListsTo enter a Full Edacs ID To enter a Type 2 Talk Group IDTo enter a Type 1 ID To enter a Partial Edacs IDID Scan Mode Receiving Trunked SystemsID Search Mode ID Scan Hold FeatureTo directly access a specific ID location Programming Scan Lists During Search ID Monitor ModeID Search Hold and Direct Entry ID in Hold Mode Deleting a Stored IDID Lockout To restore a single ID, follow these stepsTo restore all locked out IDs in a bank once Review ID LockoutTrunking Frequency Confirmation Setting the Delay Mode for Trunking ModeSetting Priority in Trunking Mode Moving between Scan List MemoriesMulti-Track Multi-Track Operational DetailsEdacs Tracking Edacs ReceptionProgramming Edacs System Frequencies An Edacs Trunked system Special Edacs Features Edacs ID Range SearchLTR Reception LTR TrackingMotorola Reception Motorola TrackingFleet Map Programming Selecting Preset Fleet MapProgramming a User Fleet Map Programming a Hybrid System Control Channel Only Mode Toggling the Status BitDisconnect Tone Detect Option End Code To connect Scanner to PC PC Control ModeRemote Interface To program your scannerStart Remote Mode and Change Transfer Speed Clone ModeScanner.uniden.com PC Control Parameter To connect the Scanner to Scanner If you wish to clone another scanner right away Care and Maintenance General UseTroubleshooting Not receiving alarms Check antenna connectionsAdjust the squelch for Trunking mode refer to Specifications Appendix State Code OrderPreset Fleet Maps E1P9 Block User Defined Fleet Maps Type I Programming InformationFleet Map Size Codes Memo Memo One Year Limited Warranty Uniden America Corporation

BCT-8 specifications

The Uniden BCT-8 is a portable scanner that has made a significant impact in the world of communications monitoring. Designed for both amateur enthusiasts and professional users, this device provides a robust set of features, making it an essential tool for anyone interested in receiving and decoding a wide range of radio frequencies.

One of the standout features of the BCT-8 is its ability to scan both conventional and trunked radio systems. This versatility allows users to listen to everything from local police and fire department communications to amateur radio operations and even aviation channels. The scanner operates between 25 MHz and 1300 MHz, covering a wide array of frequencies that cater to diverse listening interests.

The BCT-8 is equipped with a user-friendly interface, featuring an LCD screen that displays clearly readable information such as channel frequencies and descriptions. Additionally, it utilizes a programmable scan feature, enabling users to store frequencies in memory for quick access. This functionality is particularly useful for those who regularly monitor specific channels, saving time and simplifying the scanning process.

Another notable technology in the BCT-8 is its capability to decode CTCSS and DCS tones, allowing users to filter out unwanted signals and focus on the conversations that matter most to them. This feature is particularly beneficial for monitoring crowded frequencies, ensuring that listeners can hone in on their desired transmissions without interference.

The battery life of the Uniden BCT-8 is also impressive, providing extended use for those on the go. It can operate on AA batteries or a rechargeable battery pack, giving users flexibility depending on their listening habits and requirements.

In terms of build quality, the BCT-8 is sturdy yet compact, making it portable enough to carry during outdoor activities or while traveling. This is complemented by an included belt clip, allowing for hands-free operations, perfect for fieldwork or public safety applications.

Overall, the Uniden BCT-8 stands out for its extensive feature set and reliable performance, making it an ideal choice for individuals who wish to explore the rich world of radio communications. Its combination of advanced scanning capabilities, ease of use, and portability makes it a valuable addition to any scanner enthusiast's toolkit. Whether for personal use or professional monitoring, the BCT-8 excels in delivering comprehensive reception of diverse radio signals.
Top Page Image Contents