Uniden BC296D manual Holding on a Single Talkgroup, Locking Out Talkgroups, Edacs Blockout

Page 32

Holding on a Single Talkgroup

To hold on an active talkgroup when scanning or searching, press HOLD/MAN. The BC296D stops scanning and holds on the current trunking system. It only receives transmissions on the talkgroup that was active when you pressed HOLD/MAN.

To select a talkgroup to hold on when that talkgroup is not active, you must first program that talkgroup into an ID list. Then, while scanning that system, use the scroll bar to select the talkgroup ID to hold on.

To select a talkgroup to hold on when that group is not active, while ID scanning or ID searching the system, press HOLD/MAN. Then, either enter the ID or (if you have stored the ID) scroll to the ID you want to hold on.

Locking Out Talkgroups

Like conventional scanning, you can lockout unwanted talkgroup traffic on trunking systems. This is particularly important if you are ID Searching a trunking system, as many systems share both voice traffic (that you usually want to hear) with some data traffic from water meter systems, door alarms, traffic signals and other data sources that you don’t want to hear.

To lockout a talkgroup, press L/O when the scanner stops on that group. Or, if you have stored the talkgroup in an ID list, select that ID and press L/O.

To unlock a talkgroup stored in a scan list, use the scroll bar to manually select that ID, then press L/O to unlock it.

To unlock an ID you locked out during ID search or ID scan:

2:SCAN OPTION 2:TRUNK → Select the Bank

6:L/O ID REVIEW

Then, use the scroll bar to select the ID you want to unlock and press L/O.

Or, press HOLD/MAN then press L/O for 2 seconds to clear all the lockouts from the system.

EDACS Blockout

This is a powerful form of lockout that is only available for EDACS systems. EDACS Blockout lets you lockout entire Agencies or Fleets, not just individual talkgroups. To use blockout, while scanning an EDACS system, press HOLD/MAN then press L/O for 2 seconds to clear all the lockouts from the system. Then enter the agency or the

agency and fleet and press

.

then L/O. For example, to

lockout agency 4, press 04

.

L/O.

26

Image 32
Contents Page Page Contents Searching PC Control Mode Cloning Scanner Settings Page FCC Wants You To Know Scanning Legally Introduction Page Using this Manual Understanding Scanning Conventional ScanningSimplex Operation Repeater OperationTrunked Scanning Edacs Trunking Page Understanding Banks and Channels LTR TrunkingGetting More Information Quick Look at Your Scanner Buttons and ControlsDisplay Icons Icon DescriptionIncluded With Your Scanner Charging the Battery Pack Setting Up Your ScannerInstalling the Battery Pack Nickel-Metal Hydride Battery Disposal Installing the AntennaInstalling the Belt Clip Using Headphones or an External SpeakerListening Safely Turning On the Scanner Setting the SquelchBasic Operation Using the Menu Manually Selecting a ChannelScanning Programmed Channels Locking/Unlocking BanksLocking/Unlocking Channels Restoring All Locked Out ChannelsListening to the Input Channel Priority ScanningPriority Plus Scanning Using the Backlight Dimmer Light SettingDimmer Time Setting Controlling How Much Information AppearsTurning the Key Beep On/Off Locking the Enter keyLocking the Keypad Disabling the APCO25 CardMuting All Audio Turning Battery Save On/OffSetting Squelch Mode Trunk Scanning Options Searching for Active Talkgroups ID SearchScanning Only Stored Talkgroups ID Scan Monitoring Talkgroup ID’sEdacs Blockout Holding on a Single TalkgroupLocking Out Talkgroups Unlocking All Talkgroups Edacs Patch TrackingSetting Chain Search Setting Data SkipSearching Holding on an Active FrequencySkipping Frequencies Storing Found FrequenciesSearching for Subaudible Tones Setting Subaudible Tones for SearchingAutomatically Storing Frequencies Attenuating All Search Ranges Setting Delay for All Search RangesSetting a Search Range Searching for Trunk Systems Service Search Service Search SkipSearching for a Weather Broadcast Using Weather Search and Weather Alert SameUsing Weather Alert Same Dssccc Testing the Weather Alert Assigning Bank Names Bank ConfigurationProgramming Bank Information General Programming Deleting Frequencies from ChannelsTransferring Channel Information Entering Alpha InformationPage Enter the Frequency Programming Conventional ChannelsSelect a Channel to Program Assigning a Text Tag Setting the DelaySetting the Subaudible Tone Option Setting Beep Alert Setting the AttenuatorSetting the Modulation Mode Changing the Frequency StepSetting Priority Channels Programming Trunked Systems Turning I-Call On and Off for ID Search Setting Trunking DelayUsing I-Call Motorola and Edacs only Turning I-Call On for ID Scan Setting Priority Talkgroups Motorola and Edacs onlyMulti-Track Multi-Track Operational Details Using Control Channel Programming Programming Motorola SystemsProgramming Type 2/Digital 800 and 900 MHz Systems Programming Type2/Digital VHF and UHF SystemsProgramming Type I and IIi Hybrid Systems Toggling the Status Bit Toggling End Code Detect Programming Edacs Systems Programming Edacs ChannelsSetting Edacs Emergency Alert Setting Edacs Decimal ModeSetting Apco 25 Sound Quality Programming Apco SystemsPage Programming LTR Systems Programming Talkgroups Storing Known TalkgroupsStoring Found Talkgroups Press MENU/BACKSeeing Talkgroup Activity Deleting Stored Talkgroup ID’sAdding a Text Tag to an ID List Cloning Scanner Settings Using the Remote InterfacePC Control Mode Clone Care and Maintenance Troubleshooting Problem Suggestion Specifications Glossary of Terms Page Page Page Preset Fleet Maps AppendixPreset Map Block User Defined Fleet Maps Type I Programming InformationFleet Map Size Codes NWR-SAME Event Code Reverse List 71.9 74.4 77.0 79.7 82.5 85.4 88.5 BC296D Flow Charts Scan Option Conventional System Option Dimmer Dimmer Light Dimmer Time Screen Mask One Year Limited Warranty Uniden America Corporation