Woods Equipment 1050 manual Transport and Swing Lock Installation, Removing and Storing Backhoe

Page 16

from being run over ￿￿￿￿￿￿￿or crushed. Keep foldable

ROPS system in “locked up” position at all times.

„Never leave equipment unattended with engine running or with bucket in raised position. Always engage swing and boom transport locks, relieve system pressure by operating controls, and remove ignition key before leaving equipment.

Transport and Swing Lock Installation

IMPORTANT

Before operating backhoe, disengage transport lock bar and store swing lock pin. Push transport lock bar down fully to prevent damage.

Engage transport lock by fully retracting boom and dip- per. Position transport latch plate (1), located on right side of swing frame, over transport lock pin (2). Secure with safety pin (4). See Figure 10.

Center boom from side to side and install swing lock pin (6) through plates (8) and swing frame (7). Place swing lock pin (6) in storage hole (9) when not in use.

Always raise stabilizers before transporting backhoe.

REMOVING AND STORING BACKHOE

„The only time the backhoe may be operated from a position other than the operator seat is dur-

ing backhoe attachment and removal. Operator

Read Mounting ￿￿￿￿￿￿￿Kit Manual instructions on attaching and removing backhoe and use extreme care.

Always stand between rear tire and backhoe stabilizer arms or along side of tractor to avoid being trapped should the boom swing control be accidentally activated.

„Keep all persons away from operator control

area while performing adjustments, service, or maintenance.must:

Figure 10. Transport and Swing Lock Installed

3-Point Hitch Saf-T-Lok®

Center the boom, install swing lock pin, then extend boom and dipperstick. Rest bucket on the ground. Lower stabilizers to take backhoe weight off of tractor.

Remove pin that attaches top link to tractor. Remove lower 3-point arms from backhoe. Place blocks under mainframe and raise stabilizers to lower backhoe main- frame onto blocks. Block backhoe as necessary to make it stable.

Disconnect hydraulic pump from tractor and store off ground. Slowly drive tractor away from backhoe.

CLEANING

After Each Use

Remove large debris such as clumps of dirt, grass, crop residue, etc. from machine.

16 Operation

51861 (Rev. 6/16/2006)

 

 

Image 16
Contents Backhoe Introduction To the DealerTable of Contents LEA EL InstructivoBH1050 Specifications Buckets Rated CapacityIntroduction General Information Backhoe ComponentsSafety Safety RulesInstallation TrainingOperation Transportation MaintenanceStorage Safety & Instructional Decals Be CarefulSafety Operation OperationGeneral Operation Position the Machine Control Handle OperationStart Excavation Fill BucketTrenching and Excavating Dump and Return CycleTransporting Transport and Swing Lock Installation CleaningRemoving and Storing Backhoe Point Hitch Saf-T-LokPeriodically or Before Extended Storage PRE-OPERATION Check ListOwner Service Bucket Tooth ReplacementOptional Auxiliary Pump and Hydraulic System Relief ValveHydraulic Hoses and Fittings LubricationTroubleshooting Problem Possible Cause SolutionDealer Service Hydraulic Cylinder RepairGeneral Hydraulic Repair Information Boom, Dipperstick, Bucket & Stabilizer Cylinders FigureInstalling Valve Pressure Settings on Shock/Dampening ValvesHydraulic Pump Repair Hydraulic Valve RepairAdjusting System Relief Valve Pressure Shock / Dampening Pressure SettingSegment Replacement Replacing Shock/Dampening ValvesHydraulic Valve Repair Swing Cylinder Cushion OIL Flow & Figure Swing Cylinder Operational TheorySwing Cylinder Oil Flow Energy Assembly AssemblyAssembly Procedure Dealer SET-UP InstructionPlumbing Installation Dipperstick & Bucket AssemblyAttaching Backhoe to Tractor Saf-T-Lok is a registered trademark of Woods Equipment Saf-T-LokInstallation Top Link and Saf-T-Lok Hitch Installation Safety Chain Installation Seat InstallationDealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListParts Index PartsBH1050 Main Frame Assembly Hardware BH1050 Dipperstick & Bucket Assembly 34011 BH1050 Boom Assembly Valve Controls & Hardware BH1050 Console Valve Assembly Check, 2400 psi relief assemblies BH1050 Hoses & Fittings Assembly BH1050 Pump Assembly BH1050 540 RPM Hydraulic Pump BH1050 1000 RPM Hydraulic Pump BH1050 Swing Cylinder BH1050 Stabilizer Cylinder QTY Description PartBH1050 Bucket Cylinder BH1050 Boom & Dipperstick Cylinder BH1050 SAF-T-LOKASSEMBLY BH1050 Stabilizer PAD KIT Optional Bolt Torque Chart SAE Series Torque ChartAppendix Metric SeriesBolt Size Chart AbbreviationsIndex IndexWarranty Rev /23/2005 51861