Woods Equipment 1050 manual Top Link and Saf-T-Lok Hitch Installation

Page 32

Figure 25. Top Link and Saf-T-Lok Hitch Installation

IMPORTANT

■There may be more than one hole provided in tractor top link attachment bracket; select the hole that most evenly distributes the load between top link bracket and its mounting bolts. See Figure 25.

Note that the maximum width between tractor top link attachment plates must not exceed 2-1/2". This is to prevent excessive bending loads on the top link pin. Pin must be located in one of the positions shown.

A WARNING

„If tractor is equipped with draft sensing control, set control to “HEAVY” (minimum sensitivity) posi- tion.

On tractors with draft control select hole closest to sup- porting point of floating link to mount top link.

Use boom cylinder control to position backhoe main frame vertically by extending or retracting cylinder as required.

Figure 26. Saf-T-Lok Adjustment

With backhoe main frame vertical, refer to Figure 26, align double and single top link bars and bolt together using widest spread between bolts as possible. It may be necessary to move main frame slightly off vertical plane to align holes of top link.

Mount Saf-T-Lok diagonal bars to hole in top link bar as close to tractor as possible; do not mount further than 6-3/4" away from tractor. Cut end of Saf-T-Lok diagonal bars off to obtain mounting space if necessary. Place two spacer washers between double top link bar when mounting Saf-T-Lok diagonal bars.

Check distance from center of boom pivot pin and ground to be sure there is from 11" to 14" clearance. Check that console is nearly vertical with the ground.

32 Assembly

51861 (Rev. 6/16/2006)

 

 

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Backhoe Introduction To the DealerTable of Contents LEA EL InstructivoBH1050 Specifications Buckets Rated CapacityIntroduction General Information Backhoe ComponentsSafety Safety RulesInstallation TrainingOperation Storage MaintenanceTransportation Safety & Instructional Decals Be CarefulSafety General Operation OperationOperation Position the Machine Control Handle OperationStart Excavation Fill BucketTransporting Dump and Return CycleTrenching and Excavating Transport and Swing Lock Installation CleaningRemoving and Storing Backhoe Point Hitch Saf-T-LokPeriodically or Before Extended Storage PRE-OPERATION Check ListOwner Service Bucket Tooth ReplacementOptional Auxiliary Pump and Hydraulic System Relief ValveHydraulic Hoses and Fittings LubricationTroubleshooting Problem Possible Cause SolutionDealer Service Hydraulic Cylinder RepairGeneral Hydraulic Repair Information Boom, Dipperstick, Bucket & Stabilizer Cylinders FigureInstalling Valve Pressure Settings on Shock/Dampening ValvesHydraulic Pump Repair Hydraulic Valve RepairAdjusting System Relief Valve Pressure Shock / Dampening Pressure SettingSegment Replacement Replacing Shock/Dampening ValvesHydraulic Valve Repair Swing Cylinder Cushion OIL Flow & Figure Swing Cylinder Operational TheorySwing Cylinder Oil Flow Energy Assembly AssemblyAssembly Procedure Dealer SET-UP InstructionPlumbing Installation Dipperstick & Bucket AssemblyAttaching Backhoe to Tractor Saf-T-Lok is a registered trademark of Woods Equipment Saf-T-LokInstallation Top Link and Saf-T-Lok Hitch Installation Safety Chain Installation Seat InstallationDealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListParts Index PartsBH1050 Main Frame Assembly Hardware BH1050 Dipperstick & Bucket Assembly 34011 BH1050 Boom Assembly Valve Controls & Hardware BH1050 Console Valve Assembly Check, 2400 psi relief assemblies BH1050 Hoses & Fittings Assembly BH1050 Pump Assembly BH1050 540 RPM Hydraulic Pump BH1050 1000 RPM Hydraulic Pump BH1050 Swing Cylinder BH1050 Stabilizer Cylinder QTY Description PartBH1050 Bucket Cylinder BH1050 Boom & Dipperstick Cylinder BH1050 SAF-T-LOKASSEMBLY BH1050 Stabilizer PAD KIT Optional Bolt Torque Chart SAE Series Torque ChartAppendix Metric SeriesBolt Size Chart AbbreviationsIndex IndexWarranty Rev /23/2005 51861
Top Page Image Contents