Woods Equipment 1050 manual Safety Chain Installation, Seat Installation

Page 33

Make sure you meet minimum clearance distances between ROPS or tractor cab. Required head clear- ance must take priority. Refer to Danger decal on page 10. Make any adjustments required.

1.The bolt center distance attaching the diagonal brace to the top link must not be more than 6-3/4" from the tractor top link pin.

2.The bolts joining the two halves of the top link must not be less than 2-1/2" apart.

3.The vertical distance between the attachment point for the lower lift arms and the top link pin must not be less that 12".

When clearance distances are verified and attachment is complete, tighten hitch pin nuts to 600 ft-lbs. and secure with cotter pin. Hitch pin nuts may be easier to torque if the backhoe is removed from tractor.

Mount backhoe to tractor and tighten bolts attaching

Saf-T-Lok®diagonal bars to top link and bolts attaching top link bars together to 450 ft-lbs.

Safety Chain Installation

Secure backhoe to tractor by inserting safety chain through lower lift arm bracket (21) or wrapping around tractor axle (22). The preferred attachment is through bracket (21). Remove as much slack from chain as you can.

A WARNING

„Make sure safety chain is properly connected and secured to tractor.

Make sure tractor lower lift arm stabilizers (blocks or chains) are positioned to prevent lift arms and backhoe from swaying.

Secure hydraulic hoses between pump and backhoe with nylon ties to prevent them from contacting sharp objects.

Check hose positioning carefully through full range of swing cylinder movement.

Fully extend and retract all cylinders several times to purge all air from the hydraulic system. Retract all cylin- der and fill hydraulic reservoir to full mark on dipstick.

Seat Installation

The seat (2) may be adjusted fore and aft by loosening mounting hardware. It may also be moved up and down using the adjustment holes in the seat support assembly (1). Make sure you do not adjust seat into a position that will place the operator in the danger zone as outlined on the safety decals.

A DANGER

„Do not operate backhoe unless there is ade- quate operator clearance as shown on safety decal. (Refer to Danger decal in Safety Decal sec- tion.)

21.Lower lift arm pivot point

22.Tractor axle

Figure 27. Safety Chain Installation

1.Seat support assembly

2.Seat bracket

4.3/8 NC x 1" Carriage bolt

5.3/8" Lock washer

6.3/8" NC Hex nut

Figure 28. Seat Installation

51861 (Rev. 6/16/2006)

Assembly 33

 

 

Image 33
Contents Backhoe To the Dealer IntroductionLEA EL Instructivo Table of ContentsBuckets Rated Capacity BH1050 SpecificationsIntroduction Backhoe Components General InformationSafety Rules SafetyInstallation TrainingOperation Maintenance TransportationStorage Be Careful Safety & Instructional DecalsSafety Operation OperationGeneral Operation Control Handle Operation Position the MachineFill Bucket Start ExcavationDump and Return Cycle Trenching and ExcavatingTransporting Cleaning Transport and Swing Lock InstallationRemoving and Storing Backhoe Point Hitch Saf-T-LokPRE-OPERATION Check List Periodically or Before Extended StorageBucket Tooth Replacement Owner ServiceOptional Auxiliary Pump and Hydraulic System Relief ValveLubrication Hydraulic Hoses and FittingsProblem Possible Cause Solution TroubleshootingHydraulic Cylinder Repair Dealer ServiceGeneral Hydraulic Repair Information Boom, Dipperstick, Bucket & Stabilizer Cylinders FigurePressure Settings on Shock/Dampening Valves Installing ValveHydraulic Pump Repair Hydraulic Valve RepairShock / Dampening Pressure Setting Adjusting System Relief Valve PressureSegment Replacement Replacing Shock/Dampening ValvesHydraulic Valve Repair Swing Cylinder Operational Theory Swing Cylinder Cushion OIL Flow & FigureSwing Cylinder Oil Flow Energy Assembly AssemblyAssembly Procedure Dealer SET-UP InstructionDipperstick & Bucket Assembly Plumbing InstallationAttaching Backhoe to Tractor Saf-T-Lok is a registered trademark of Woods Equipment Saf-T-LokInstallation Top Link and Saf-T-Lok Hitch Installation Seat Installation Safety Chain InstallationDealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListParts Parts IndexBH1050 Main Frame Assembly Hardware BH1050 Dipperstick & Bucket Assembly 34011 BH1050 Boom Assembly Valve Controls & Hardware BH1050 Console Valve Assembly Check, 2400 psi relief assemblies BH1050 Hoses & Fittings Assembly BH1050 Pump Assembly BH1050 540 RPM Hydraulic Pump BH1050 1000 RPM Hydraulic Pump BH1050 Swing Cylinder QTY Description Part BH1050 Stabilizer CylinderBH1050 Bucket Cylinder BH1050 Boom & Dipperstick Cylinder BH1050 SAF-T-LOKASSEMBLY BH1050 Stabilizer PAD KIT Optional SAE Series Torque Chart Bolt Torque ChartAppendix Metric SeriesAbbreviations Bolt Size ChartIndex IndexWarranty Rev /23/2005 51861