Woods Equipment 1050 manual Bolt Size Chart, Abbreviations

Page 56

BOLT SIZE CHART

NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts.

SAE Bolt Thread Sizes
5/16	3/8	1/2	5/8	3/4	7/8

IN				1						2								3								4								5								6								7

MM

25

50

75

100

125

150

175

Metric Bolt Thread Sizes
8MM	10MM	12MM	14MM	16MM	18MM

ABBREVIATIONS

AG	Agriculture
ATF	Automatic Transmission Fluid
BSPP	British Standard Pipe Parallel
BSPTM	British Standard Pipe Tapered Male
CV	Constant Velocity
CCW	Counter-Clockwise
CW	Clockwise
F	Female
GA	Gauge
GR (5, etc.)	Grade (5, etc.)
HHCS	Hex Head Cap Screw
HT	Heat-Treated
JIC	Joint Industry Council 37° Degree Flare
LH	Left Hand
LT	Left
m	Meter
mm	Millimeter
M	Male
MPa	Mega Pascal
N	Newton

NC	National Coarse
NF	National Fine
NPSM	National Pipe Straight Mechanical
NPT	National Pipe Tapered
NPT SWF	National Pipe Tapered Swivel Female
ORBM	O-Ring Boss - Male
P	Pitch
PBY	Power-Beyond
psi	Pounds per Square Inch
PTO	Power Take Off
QD	Quick Disconnect
RH	Right Hand
ROPS	Roll-Over Protective Structure
RPM	Revolutions Per Minute
RT	Right
SAE	Society of Automotive Engineers
UNC	Unified Coarse
UNF	Unified Fine
UNS	Unified Special

56Appendix

Bolt Torque & Size Charts (Rev. 10/10/2005)

Image 56

Contents Backhoe Introduction To the DealerTable of Contents LEA EL InstructivoBH1050 Specifications Buckets Rated CapacityIntroduction General Information Backhoe ComponentsSafety Safety RulesInstallation TrainingOperation Storage MaintenanceTransportation Safety & Instructional Decals Be CarefulSafety General Operation OperationOperation Position the Machine Control Handle OperationStart Excavation Fill BucketTransporting Dump and Return CycleTrenching and Excavating Transport and Swing Lock Installation CleaningRemoving and Storing Backhoe Point Hitch Saf-T-LokPeriodically or Before Extended Storage PRE-OPERATION Check ListOwner Service Bucket Tooth ReplacementOptional Auxiliary Pump and Hydraulic System Relief ValveHydraulic Hoses and Fittings LubricationTroubleshooting Problem Possible Cause SolutionDealer Service Hydraulic Cylinder RepairGeneral Hydraulic Repair Information Boom, Dipperstick, Bucket & Stabilizer Cylinders FigureInstalling Valve Pressure Settings on Shock/Dampening ValvesHydraulic Pump Repair Hydraulic Valve RepairAdjusting System Relief Valve Pressure Shock / Dampening Pressure SettingSegment Replacement Replacing Shock/Dampening ValvesHydraulic Valve Repair Swing Cylinder Cushion OIL Flow & Figure Swing Cylinder Operational TheorySwing Cylinder Oil Flow Energy Assembly AssemblyAssembly Procedure Dealer SET-UP InstructionPlumbing Installation Dipperstick & Bucket AssemblyAttaching Backhoe to Tractor Saf-T-Lok is a registered trademark of Woods Equipment Saf-T-LokInstallation Top Link and Saf-T-Lok Hitch Installation Safety Chain Installation Seat InstallationDealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListParts Index PartsBH1050 Main Frame Assembly Hardware BH1050 Dipperstick & Bucket Assembly 34011 BH1050 Boom Assembly Valve Controls & Hardware BH1050 Console Valve Assembly Check, 2400 psi relief assemblies BH1050 Hoses & Fittings Assembly BH1050 Pump Assembly BH1050 540 RPM Hydraulic Pump BH1050 1000 RPM Hydraulic Pump BH1050 Swing Cylinder BH1050 Stabilizer Cylinder QTY Description PartBH1050 Bucket Cylinder BH1050 Boom & Dipperstick Cylinder BH1050 SAF-T-LOKASSEMBLY BH1050 Stabilizer PAD KIT Optional Bolt Torque Chart SAE Series Torque ChartAppendix Metric SeriesBolt Size Chart AbbreviationsIndex IndexWarranty Rev /23/2005 51861