Panasonic D6KE Projecting a image,  Switching on the projector, Power switch AC in terminal

Page 19

Projecting

Projecting a image

Switching on the projector

Making adjustment and selection

When using an optional lens, install a projection lens before switch on the projector.

1.Connect the supplied mains lead (220 - 240 V AC, 50 Hz/60 Hz) to the AC IN terminal.

2.Remove the projection lens cover from the lens.

3.Switch the POWER switch on that is on the side of the projector.

The power indicator lamp on the projector will flash in red. After a short period, the indicator will illuminate and the projector will enter standby mode.

POWER switch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

AC IN terminal

 

 

 

4.Press the POWER ON button

The power indicator lamp illuminates in green and soon the image is projected on the screen.

POWER ON button

It is recommended that the projector be allowed to warm up for at least 30 minutes before any adjustments are made to the focus.

1.Roughly adjust the focus of the lens.

2.Select and set the projection scheme of INSTALLATION and COOLING CONDITION settings in PROJECTOR SETUP menu.

3.Select the input signal by pressing the INPUT SELECT buttons.

4.Adjust the vertical tilt of the projector with the front leg adjusters.

5.Adjust the shift position of the projection.

If the input signal is RGB signal, additionally press the AUTO SETUP button to adjust the position of the image.

6.Zoom the lens so the image fills the screen.

7.Readjust the focus.

8.Readjust the zoom so that the image size fits in the screen.

Adjusting focus, zoom and shift

Control buttons of the

Pressing the LENS button changes the

setup screen in order of FOCUS, ZOOM

projector

and SHIFT. Press F G I H to adjust.

 

 

Press FOCUS, ZOOM or SHIFT button

Remote control buttons to display the setup screen. Press F G

 

I H to adjust.

 

INPUT SELECT buttons

Basic Operation

.

NOTE:

If the projector is powered up at about 0 °C (32 °F), a warm- up period of approximately 5 minutes may be necessary to start projection. The temperature monitor (TEMP) lamp lights up during the warm-up period. When the warm-up is completed, the temperature monitor (TEMP) lamp turns off and the image is projected on the screen.

If the temperature of the operating environment is low and warm-up takes more than 5 minutes, the projector will judge that a problem has occurred and the power will be turned off automatically. If this happens, increase the temperature around the projector so that it is 0 °C (32 °F) or higher, and then turn on the POWER switch and press the POWER ON button again.

LENS button

CAUTION:

Be careful not to catch your fingers between the lens and shroud when shifting the lens.

NOTE:

The setup screen will be displayed with the optional fixed lens though, it will not be functioning.

Pressing F G I or H for 3 seconds or more, performance the adjustment faster.

ENGLISH - 19

Image 19
Contents PT-DZ6700E PT-DW6300E PT-D6000E PT-D5000E To rain or moisture Important Safety NoticeFor business users in the European Union Important Safety NoticeEnvironment care information for users in China Important the Moulded Plug U.K. only For Your SAFETY, Please Read the Following Text CarefullyContents Precautions with regard to safety Precautions with regard to safety Do not use chemical treated wipes when cleaning Do not set up the projector outdoorsRemove the used batteries from the remote control promptly Do not put your weight on this projectorOrder to get the best picture quality Replacement of the lamp unit should only be carriedDo not reach for the openings beside the optical Be sure to always remove the lens during transportSecurity OthersAccessories Projector body About Your Projector Top, front and bottom view About Your Projector  Side viewsRemote control IN/OUT terminal. It is effective to use the wired remote When multiple projectors are connected as partNumber, and the remote control 2 digits ID number must Be set to match the intended projector. The defaultOver 10 cm Setting up Cautions when setting the projectors Projection method Attaching the projection lens to the projector Setting upRemoving and attaching the projection lens  Removing the projection lens from the projectorMains lead  ConnectingProjecting  Switching on the projector Adjusting focus, zoom and shift Power switch AC in terminal Direct power off function Projecting  Switching off the projector Adjustment range after lens Position optical shift  Facing to the projector Remote control operationSetting up the image position automatically Operating rangeChanging the picture aspect ratio Switching the input signalStopping the projection Clearing the on-screen menuResetting to the factory default Using an assigned functionDisplaying the status of the projector Main menu and Sub-menu Menu NavigationPT-DZ6710E/PT-DZ6700E/PT-DW6300E only RS-232CSecurity Menu Navigation Displaying the Main menu  Adjusting with the bar scale items Operating procedure Navigating through the menu Temp indicator Monitor Lamp indicatorsManaging the indicated problems  LAMP1/LAMP2 indicatorStatus in Projector Setup menu Monitor Lamp indicators  Filter indicatorStatus in Projector  Before replacing the Lamp unit Replacement When to replace the lamp unit Replacing the Lamp unitHandle  Removing and replacing the lamp unitLamp unit cover fixing screw Lamp u nit fixing screwsReplacing the Auto Cleaning Filter ACF Troubleshooting Technical Information List of compatible signalsPT-DW6300E  Display dots of each modelPT-DZ6710E PT-DZ6700ETechnical Information SpecificationsSerial  Attachment procedure Ceiling mount bracket safeguardsCeiling mount Trademark acknowledgements DimensionsUnit mm inch Index Index