Panasonic PT-DW6300K, D6KE manual Important the Moulded Plug U.K. only

Page 4

Important Information

Important Safety Notice

IMPORTANT: THE MOULDED PLUG (U.K. only)

FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY.

This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 13 amp fuse is fitted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of13 amps and that it is approved by ASTA or BSI to BS1362.

Check for the ASTA mark a or the BSI mark ` on the body of the fuse.

If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover, the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from an Authorised Service Centre.

If the fitted moulded plug is unsuitable for the mains socket in your home, then the fuse should be removed and the plug cut off and disposed of safely. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket.

If a new plug is to be fitted, please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician.

WARNING: THIS APPLIANCE MUST BE EARTHED.

IMPORTANT: The wires in this mains lead are coloured in accordance with the following code: Green - and - Yellow: Earth

Blue:Neutral

Brown:Live

As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows.

The wire which is coloured GREEN - AND - YELLOW must be connected to the terminal in the plug which is marked with the letter E or by the Earth symbol W or coloured GREEN or GREEN - AND - YELLOW.

The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured RED.

How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.

BS1363/A

N

 

13A250V

-8

 

 

HE

L

 

ASA

 

ENGLISH - 4

Image 4
Contents PT-DZ6700E PT-DW6300E PT-D6000E PT-D5000E Important Safety Notice To rain or moistureFor business users in the European Union Important Safety NoticeEnvironment care information for users in China For Your SAFETY, Please Read the Following Text Carefully Important the Moulded Plug U.K. onlyContents Precautions with regard to safety Precautions with regard to safety Do not set up the projector outdoors Remove the used batteries from the remote control promptlyDo not put your weight on this projector Do not use chemical treated wipes when cleaningReplacement of the lamp unit should only be carried Do not reach for the openings beside the opticalBe sure to always remove the lens during transport Order to get the best picture qualityOthers SecurityAccessories Projector body About Your Projector Top, front and bottom view  Side views About Your ProjectorRemote control When multiple projectors are connected as part Number, and the remote control 2 digits ID number mustBe set to match the intended projector. The default IN/OUT terminal. It is effective to use the wired remoteSetting up  Cautions when setting the projectorsProjection method Over 10 cmSetting up Removing and attaching the projection lens Removing the projection lens from the projector  Attaching the projection lens to the projector Connecting Mains lead Switching on the projector  Adjusting focus, zoom and shiftPower switch AC in terminal Projecting Direct power off function Projecting  Switching off the projector Adjustment range after lens Position optical shift Remote control operation Setting up the image position automaticallyOperating range  Facing to the projectorSwitching the input signal Stopping the projectionClearing the on-screen menu Changing the picture aspect ratioResetting to the factory default Using an assigned functionDisplaying the status of the projector Menu Navigation Main menu and Sub-menuRS-232C PT-DZ6710E/PT-DZ6700E/PT-DW6300E onlyMenu Navigation Security Adjusting with the bar scale items  Operating procedureNavigating through the menu  Displaying the Main menuMonitor Lamp indicators Managing the indicated problems LAMP1/LAMP2 indicator  Temp indicatorStatus in Projector Setup menu Monitor Lamp indicators  Filter indicatorStatus in Projector Replacement  When to replace the lamp unitReplacing the Lamp unit  Before replacing the Lamp unit Removing and replacing the lamp unit Lamp unit cover fixing screwLamp u nit fixing screws HandleReplacing the Auto Cleaning Filter ACF Troubleshooting List of compatible signals Technical Information Display dots of each model PT-DZ6710EPT-DZ6700E PT-DW6300ESpecifications Technical InformationSerial  Attachment procedure Ceiling mount bracket safeguardsCeiling mount Trademark acknowledgements DimensionsUnit mm inch Index Index