Panasonic PT-D5600UL, PT-DW5000U manual Setting projector ID number to remote control

Page 15

Setting projector ID number to remote control

Every projector has its ID number and the ID number of the controlling projector must be set to the remote control in advance so that the user can operate the remote control. The ID number of the projector is set to “ALL” on shipping, and use the ID ALL button of the remote control when using only a single projector.

Procedure of ID setting

Change the position of the operation mode selector switch to “Computer”.

Press the ID SET button, and within five seconds use the number (0 to 9) buttons to enter the 2-digit ID number set by the projector.

Change the position of the operation mode selector switch to “Projector”.

However, if the ID ALL button is pressed, the projector can be controlled regardless of the ID number of the projector (simultaneous control mode).

Attention • Do not press the ID SET button accidentally or carelessly because the ID number on the remote control can be set even when no projector is around.

If the ID SET button is pressed, the ID number goes back to the one set before pressing the ID SET button unless a numeric button is pressed within five seconds after the ID SET button is pressed.

•Your specified ID number is stored in the remote control unit unless another one is specified later. However, the stored ID will be erased if the batteries of the remote control are left exhausted. When the dry cells are replaced, set the same ID number again.

•When specifying the ID number, enter a 2-digit number even if the ID has only one digit. (Example: set “02” if the ID number is “2.”)

Using the remote control as a PC mouse

PAGE UP button

Operation mode selector switch

Left click () button

ENTER button

Right click () button

PAGE DOWN button

Operation mode selector switch

Click button

Put the knob to the Computer position.

•ENTER button

Pressing the front, rear, left and right edges of the button moves the mouse cursor up, down, left and right.

•Right click ( ) button

This button can be used as the right mouse button.

•Left click ( ) button

This button can be used as the left mouse button.

•PAGE UP button

This button can be used as the Page Up button on the PC keyboard.

•PAGE DOWN button

This button can be used as the Page Down button on the PC keyboard.

•Click button

This button can be used as the left mouse button.

Note • To use the remote control as a mouse, please purchase an optional wireless mouse receiver (model No.: ET-RMRC2).

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Commercial Use PT-DW5000ULModel number PT-D5600U/PT-D5600UL/PT-DW5000U/PT-DW5000UL Dear Panasonic CustomerPT-D5600U/PT-D5600UL/PT-DW5000U/PT-DW5000UL Contents Precautions with regard to safety Do not place liquid containers on top of the projector Do not insert any foreign objects into the projectorAlways disconnect all cables before moving the projector Do not use the old lamp unit AccessoriesUse only the Specified battery Do not look into the lens while the projector is being usedPrecautions on handling Name and function of parts Set to Computer When the operation mode selectorStatus LED lights Front and side of the projectorRear view of the main unit Controls on rear panel Side-mounted connection terminals Using the remote control unit Effective range of remote control operationLoading dry cells Setting projector ID number to remote control Using the remote control as a PC mouseOperation mode selector switch Projection schemes InstallationUsing a wired remote control Installation geometryPT-D5600U, PT-D5600UL Projection distance by projection lensInstallation 817 PT-DW5000U, PT-DW5000ULCalculation formulas for projection distance by lens types Connection Setup precautionsExample of connecting with PCs Example of connecting with AV productsPowering up the projector Making adjustment and selectionProjection Direct power off function Powering off the projectorChoose an item and adjust it using buttons How to adjust the lensHow to remove the projection lens How to adjust the lens position to the left or rightUsing the digital zoom D.ZOOM + function Automatic adjustment Auto SetupUsing the Freeze function Using the Shutter functionStructure of menu screens On-screen menusReturning to the previous Menu items settingResetting to the factory default Basic menu operationsAdjusting the picture Position Adjusting the positionTV-SYSTEM SystemClock Phase ZoomKeystone Blanking How to use Advanced MenuInput Resolution Digital Cinema RealityXGA Mode Sxga ModeRaster Position OPTION1 settings DESK/CEILING OPTION2 settingsLamp Power FRONT/REARFAN CONTROL1 PasswordFAN CONTROL2 System InformationSetting the security Connection example Setting the networkConnecting the PC System requirementsExamples of connection Using the serial terminalsPin assignments and signal names Communication conditions Factory settingPin assignments and control Control commandsCable specifications Connecting to a PC Computer Projector DTE specificationsIndication of lamp monitor Dismantle the air filter Cleaning and replacement of air filterProcedure of cleaning Clean the air filterReplacing the lamp unit Timing of lamp unit replacementHave a Phillips screwdriver ready ahead of time Lamp unit replacement stepsRemove the two screws securing the fan unit Lamp unit will be hot after it has been usedSelect the lamp which has been replaced with the and buttons Click OK Using Web Browser ControlAccessing from the Web browser Password changeBasic control Mail set up buttonPower On/Off control Shutter control Change password buttonError information Monitor informationOK Normal operation Failed Occurrence of trouble When Failed has appeared for an item Parameter Description Mail setupError Mail setup page ContinuingPing test DNS server set upPOP server setup Button to update settingsAdjust clock Contents of mail sentNetwork status Network configCommand Control Description Remarks Using the PJLink protocolSupported commands PJLink security authenticationNot turn on Symptoms ChecksPower does Remote controlPT-D5600U PT-D5600UL PT-DW5000U SpecificationsWireless mouse receiver Length of power supply cord CabinetOutside dimensions Remote control Power sourcePAL-M/PAL60 PAL/PAL-N/SECAM Compatible Signal ListDimensions Installation dimensions diagramTrademark Acknowledgement Concernant LA Sécurité Ne pas retirer le couvercle ou le modifier Précautions concernant la sécuritéNe pas couvrir le filtre et la sortie d’air Ne pas surcharger la prise de courantNe pas placer le projecteur sur des surfaces instables Ne pas placer des récipients de liquide sur le projecteurNe pas mettre d’objets étrangers dans le projecteur Ne pas placer d’objets lourds sur le projecteur ’utiliser que la pile indiquée’utilisez pas un bloc lampe usagé Mise au rebut Nettoyage et maintenancePrécautions pour la manipulation Précautions pour le transportPériode de remplacement de la lampe Remplacement de la lampeProcédure de remplacement de la lampe La lampe est chaude si elle vient d’être utiliséePréparez un tournevis Phillips à l’avance INIT. Compt Panasonic Projector Systems Company Technical SupportPanasonic Canada Inc

PT-DW5000U, PT-D5600U, PT-D5600UL specifications

The Panasonic PT-D5600UL, PT-D5600U, and PT-DW5000U projectors are designed for professional use in a variety of environments, ranging from corporate settings to educational institutions and large venues. These projectors are renowned for their exceptional image quality, versatile features, and robust performance.

At the heart of these projectors is the high-performance DLP technology, which offers remarkable brightness and contrast. The PT-D5600UL and PT-D5600U offer a brightness level of 6000 lumens, while the PT-DW5000U provides 5000 lumens, ensuring clear visibility even in well-lit rooms. This remarkable brightness coupled with a solid contrast ratio provides sharp and vivid images, whether for video presentations or intricate graphics.

The three models are equipped with a versatile lens system, which includes various optional lenses to accommodate different installation requirements. The lens shift feature enhances installation flexibility, allowing for simple adjustments to the image without distortion. The projectors support various resolutions and aspect ratios, including WUXGA (1920 x 1200) for the PT-D5600UL and PT-D5600U, and WXGA (1280 x 800) for the PT-DW5000U, ensuring that users can display content with high precision and clarity.

Panasonic’s innovative Daylight View technology enhances image quality by automatically adjusting color reproduction to match ambient lighting conditions, ensuring that images remain visible and consistent throughout the day. Furthermore, these projectors employ a durable lamp life of up to 3000 hours in normal mode, reducing maintenance needs and costs for users.

For enhanced connectivity, the PT-D5600UL, PT-D5600U, and PT-DW5000U are equipped with multiple input options, including HDMI, DVI-D, and VGA ports, supporting a range of multimedia devices. The projectors also support network monitoring and control via LAN, allowing users to manage settings and monitor performance remotely.

In terms of build quality, these projectors are designed for reliability and longevity. Their robust chassis and advanced cooling system ensure stable operation even during extended use, making them ideal for events or long presentations. Overall, the Panasonic PT-D5600UL, PT-D5600U, and PT-DW5000U projectors deliver a seamless and high-quality projection experience, solidifying Panasonic’s reputation as a leader in the projection technology market.
Top Page Image Contents