Panasonic PT-D5600UL, PT-DW5000U manual Powering off the projector, Direct power off function

Page 24

Projection

Powering off the projector

Press the POWER OFF “ ” button.

Select “OK” with or button and press the ENTER button.

(or press the POWER OFF “ ” button again.)

The projection of the image stops, and the power indicator of the main unit lights up orange. (The cooling fan keeps running.)

Wait until the power indicator of the main unit turns to red (i.e., until the cooling fan stops).

Press the “ ” marked side of the MAIN POWER switch to remove all power from the projector.

Attention • Do not turn the power supply off and then immediately back on again.

Turning on the power supply will not light up the light source lamp if the lamp is in the process of cooling down after turning off the power supply. To light up the lamp, turn on the power supply again when the lamp has been cooled sufficiently. Turning on the power supply with the lamp in the hot condition may shorten the lamp life.

Note • The projector consumes approximately 10 watts of power even in standby mode after the cooling fan stops. (Power indicator lit in red)

•If you re-power the projector after shutting off the main power inadvertently, the projection lamp may remain unlit. Please turn the power on again after a while.

Direct power off function

The power supplied internally causes the cooling fan to continue operating and cool off in the event that the power has failed or even after the power cord is accidentally disconnected immediately after the power has been turned off.

Note • When the lamp has been cooled by the direct power OFF function, it sometimes

takes longer than usual for the lamp to light up again.

•While the cooling fan is operating, do not place the projector inside a box or bag.

•The operation time of the cooling fan will be less if fewer than 4 minutes have elapsed since the power was turned on.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents PT-DW5000UL Commercial UseDear Panasonic Customer Model number PT-D5600U/PT-D5600UL/PT-DW5000U/PT-DW5000ULPT-D5600U/PT-D5600UL/PT-DW5000U/PT-DW5000UL Contents Precautions with regard to safety Do not place liquid containers on top of the projector Do not insert any foreign objects into the projectorAlways disconnect all cables before moving the projector Accessories Use only the Specified batteryDo not look into the lens while the projector is being used Do not use the old lamp unitPrecautions on handling Name and function of parts When the operation mode selector Set to ComputerFront and side of the projector Status LED lightsRear view of the main unit Controls on rear panel Side-mounted connection terminals Using the remote control unit Effective range of remote control operationLoading dry cells Setting projector ID number to remote control Using the remote control as a PC mouseOperation mode selector switch Installation Using a wired remote controlInstallation geometry Projection schemesProjection distance by projection lens PT-D5600U, PT-D5600ULInstallation PT-DW5000U, PT-DW5000UL 817Calculation formulas for projection distance by lens types Setup precautions ConnectionExample of connecting with AV products Example of connecting with PCsPowering up the projector Making adjustment and selectionProjection Powering off the projector Direct power off functionHow to adjust the lens How to remove the projection lensHow to adjust the lens position to the left or right Choose an item and adjust it using buttonsAutomatic adjustment Auto Setup Using the Freeze functionUsing the Shutter function Using the digital zoom D.ZOOM + functionOn-screen menus Structure of menu screensMenu items setting Resetting to the factory defaultBasic menu operations Returning to the previousAdjusting the picture Adjusting the position TV-SYSTEMSystem PositionClock Phase ZoomKeystone How to use Advanced Menu Input ResolutionDigital Cinema Reality BlankingXGA Mode Sxga ModeRaster Position OPTION1 settings OPTION2 settings Lamp PowerFRONT/REAR DESK/CEILINGPassword FAN CONTROL2System Information FAN CONTROL1Setting the security Setting the network Connecting the PCSystem requirements Connection exampleUsing the serial terminals Pin assignments and signal namesCommunication conditions Factory setting Examples of connectionControl commands Cable specificationsConnecting to a PC Computer Projector DTE specifications Pin assignments and controlIndication of lamp monitor Cleaning and replacement of air filter Procedure of cleaningClean the air filter Dismantle the air filterTiming of lamp unit replacement Replacing the lamp unitLamp unit replacement steps Remove the two screws securing the fan unitLamp unit will be hot after it has been used Have a Phillips screwdriver ready ahead of timeSelect the lamp which has been replaced with the and buttons Using Web Browser Control Accessing from the Web browserPassword change Click OKMail set up button Power On/Off control Shutter controlChange password button Basic controlError information Monitor informationOK Normal operation Failed Occurrence of trouble Mail setup When Failed has appeared for an item Parameter DescriptionMail setup page Continuing ErrorDNS server set up POP server setupButton to update settings Ping testContents of mail sent Adjust clockNetwork config Network statusUsing the PJLink protocol Supported commandsPJLink security authentication Command Control Description RemarksSymptoms Checks Power doesRemote control Not turn onSpecifications PT-D5600U PT-D5600UL PT-DW5000ULength of power supply cord Cabinet Outside dimensionsRemote control Power source Wireless mouse receiverCompatible Signal List PAL-M/PAL60 PAL/PAL-N/SECAMDimensions Installation dimensions diagramTrademark Acknowledgement Concernant LA Sécurité Précautions concernant la sécurité Ne pas couvrir le filtre et la sortie d’airNe pas surcharger la prise de courant Ne pas retirer le couvercle ou le modifierNe pas placer le projecteur sur des surfaces instables Ne pas placer des récipients de liquide sur le projecteurNe pas mettre d’objets étrangers dans le projecteur Ne pas placer d’objets lourds sur le projecteur ’utiliser que la pile indiquée’utilisez pas un bloc lampe usagé Nettoyage et maintenance Précautions pour la manipulationPrécautions pour le transport Mise au rebutRemplacement de la lampe Période de remplacement de la lampeProcédure de remplacement de la lampe La lampe est chaude si elle vient d’être utiliséePréparez un tournevis Phillips à l’avance INIT. Compt Panasonic Projector Systems Company Technical SupportPanasonic Canada Inc

PT-DW5000U, PT-D5600U, PT-D5600UL specifications

The Panasonic PT-D5600UL, PT-D5600U, and PT-DW5000U projectors are designed for professional use in a variety of environments, ranging from corporate settings to educational institutions and large venues. These projectors are renowned for their exceptional image quality, versatile features, and robust performance.

At the heart of these projectors is the high-performance DLP technology, which offers remarkable brightness and contrast. The PT-D5600UL and PT-D5600U offer a brightness level of 6000 lumens, while the PT-DW5000U provides 5000 lumens, ensuring clear visibility even in well-lit rooms. This remarkable brightness coupled with a solid contrast ratio provides sharp and vivid images, whether for video presentations or intricate graphics.

The three models are equipped with a versatile lens system, which includes various optional lenses to accommodate different installation requirements. The lens shift feature enhances installation flexibility, allowing for simple adjustments to the image without distortion. The projectors support various resolutions and aspect ratios, including WUXGA (1920 x 1200) for the PT-D5600UL and PT-D5600U, and WXGA (1280 x 800) for the PT-DW5000U, ensuring that users can display content with high precision and clarity.

Panasonic’s innovative Daylight View technology enhances image quality by automatically adjusting color reproduction to match ambient lighting conditions, ensuring that images remain visible and consistent throughout the day. Furthermore, these projectors employ a durable lamp life of up to 3000 hours in normal mode, reducing maintenance needs and costs for users.

For enhanced connectivity, the PT-D5600UL, PT-D5600U, and PT-DW5000U are equipped with multiple input options, including HDMI, DVI-D, and VGA ports, supporting a range of multimedia devices. The projectors also support network monitoring and control via LAN, allowing users to manage settings and monitor performance remotely.

In terms of build quality, these projectors are designed for reliability and longevity. Their robust chassis and advanced cooling system ensure stable operation even during extended use, making them ideal for events or long presentations. Overall, the Panasonic PT-D5600UL, PT-D5600U, and PT-DW5000U projectors deliver a seamless and high-quality projection experience, solidifying Panasonic’s reputation as a leader in the projection technology market.
Top Page Image Contents