Panasonic PT-D5600UL, PT-DW5000U Select the lamp which has been replaced with the and buttons

Page 45

MENU

PICTURE

POSITION

ADVANCED MENU

LANGUAGE

OPTION1

OPTI0N2

TEST PATTERN

SYSTEM INFORMATION

ROM VERSION

1. 00. 00

SET RUNTIME

300h

LAMP1 LOW

100h

HIGH

200h

TOTAL

300h

LAMP2 LOW

100h

 

LAMP TIME RESET

LAMP1

 

LAD55

1433h

LAD55L

0h

LAMP2

 

LAD55

1100h

LAD55L

0h

Insert the power cord plug into the wall outlet and then press the MAIN POWER switch.

Attention • If the power does not turn on even after turning the MAIN POWER switch “I”, turn the MAIN POWER “O”, confirm that

the lamp unit and door are installed correctly, and turn on again.

Press the “ I ” button so that a picture is projected onto the screen.

Press the “MENU” button to display the MAIN MENU screen, and then press the and buttons to move the cursor to select “OPTION2”.

Press the “ENTER” button to display the “OPTION2” screen, and select “SYSTEM INFORMATION” with the and buttons.

Press the “ENTER” button.

The SYSTEM INFORMATION screen will be displayed.

Press and hold the “ENTER” button on the projector or the remote control for approximately 3 seconds.

An item “LAMP TIME RESET” will be added.

Select the lamp which has been replaced with the and buttons.

LAMP1: Replace the LAMP UNIT 1

LAMP2: Replace the LAMP UNIT 2

Press the ENTER button, and when the “LAMP TIME RESET” display flashes, press the ENTER button again.

The used hours of the specified lamp unit will be reset to zero.

When more than one lamp has been replaced, repeat the procedure from step .

Note • When the “LAMP TIME RESET” display flashes, the lamp time reset can be canceled by pressing the MENU button.

•The used hours of the lamp units can also be reset to zero

by taking the following action instead of steps to . When lamp unit 1 has been replaced:

In the standby mode, press the number buttons in the sequence of 737381, and then press the ENTER button.

When lamp unit 2 has been replaced:

In the standby mode, press the number buttons in the sequence of 737382, and then press the ENTER button. When the used hours have been reset, the lamp monitor (LAMP1/LAMP2) will flash for 3 seconds.

45

Page 44 Page 46
Image 45
Page 44 Page 46
Contents Commercial Use PT-DW5000ULModel number PT-D5600U/PT-D5600UL/PT-DW5000U/PT-DW5000UL Dear Panasonic CustomerPT-D5600U/PT-D5600UL/PT-DW5000U/PT-DW5000UL Contents Precautions with regard to safety Do not place liquid containers on top of the projector Do not insert any foreign objects into the projectorAlways disconnect all cables before moving the projector Use only the Specified battery AccessoriesDo not look into the lens while the projector is being used Do not use the old lamp unitPrecautions on handling Name and function of parts Set to Computer When the operation mode selectorStatus LED lights Front and side of the projectorRear view of the main unit Controls on rear panel Side-mounted connection terminals Using the remote control unit Effective range of remote control operationLoading dry cells Setting projector ID number to remote control Using the remote control as a PC mouseOperation mode selector switch Using a wired remote control InstallationInstallation geometry Projection schemesPT-D5600U, PT-D5600UL Projection distance by projection lensInstallation 817 PT-DW5000U, PT-DW5000ULCalculation formulas for projection distance by lens types Connection Setup precautionsExample of connecting with PCs Example of connecting with AV productsPowering up the projector Making adjustment and selectionProjection Direct power off function Powering off the projectorHow to remove the projection lens How to adjust the lensHow to adjust the lens position to the left or right Choose an item and adjust it using buttonsUsing the Freeze function Automatic adjustment Auto SetupUsing the Shutter function Using the digital zoom D.ZOOM + functionStructure of menu screens On-screen menusResetting to the factory default Menu items settingBasic menu operations Returning to the previousAdjusting the picture TV-SYSTEM Adjusting the positionSystem PositionClock Phase ZoomKeystone Input Resolution How to use Advanced MenuDigital Cinema Reality BlankingXGA Mode Sxga ModeRaster Position OPTION1 settings Lamp Power OPTION2 settingsFRONT/REAR DESK/CEILINGFAN CONTROL2 PasswordSystem Information FAN CONTROL1Setting the security Connecting the PC Setting the networkSystem requirements Connection examplePin assignments and signal names Using the serial terminalsCommunication conditions Factory setting Examples of connectionCable specifications Control commandsConnecting to a PC Computer Projector DTE specifications Pin assignments and controlIndication of lamp monitor Procedure of cleaning Cleaning and replacement of air filterClean the air filter Dismantle the air filterReplacing the lamp unit Timing of lamp unit replacementRemove the two screws securing the fan unit Lamp unit replacement stepsLamp unit will be hot after it has been used Have a Phillips screwdriver ready ahead of timeSelect the lamp which has been replaced with the and buttons Accessing from the Web browser Using Web Browser ControlPassword change Click OKPower On/Off control Shutter control Mail set up buttonChange password button Basic controlError information Monitor informationOK Normal operation Failed Occurrence of trouble When Failed has appeared for an item Parameter Description Mail setupError Mail setup page ContinuingPOP server setup DNS server set upButton to update settings Ping testAdjust clock Contents of mail sentNetwork status Network configSupported commands Using the PJLink protocolPJLink security authentication Command Control Description RemarksPower does Symptoms ChecksRemote control Not turn onPT-D5600U PT-D5600UL PT-DW5000U SpecificationsOutside dimensions Length of power supply cord CabinetRemote control Power source Wireless mouse receiverPAL-M/PAL60 PAL/PAL-N/SECAM Compatible Signal ListDimensions Installation dimensions diagramTrademark Acknowledgement Concernant LA Sécurité Ne pas couvrir le filtre et la sortie d’air Précautions concernant la sécuritéNe pas surcharger la prise de courant Ne pas retirer le couvercle ou le modifierNe pas placer le projecteur sur des surfaces instables Ne pas placer des récipients de liquide sur le projecteurNe pas mettre d’objets étrangers dans le projecteur Ne pas placer d’objets lourds sur le projecteur ’utiliser que la pile indiquée’utilisez pas un bloc lampe usagé Précautions pour la manipulation Nettoyage et maintenancePrécautions pour le transport Mise au rebutPériode de remplacement de la lampe Remplacement de la lampeProcédure de remplacement de la lampe La lampe est chaude si elle vient d’être utiliséePréparez un tournevis Phillips à l’avance INIT. Compt Panasonic Projector Systems Company Technical SupportPanasonic Canada Inc

PT-DW5000U, PT-D5600U, PT-D5600UL specifications

The Panasonic PT-D5600UL, PT-D5600U, and PT-DW5000U projectors are designed for professional use in a variety of environments, ranging from corporate settings to educational institutions and large venues. These projectors are renowned for their exceptional image quality, versatile features, and robust performance.

At the heart of these projectors is the high-performance DLP technology, which offers remarkable brightness and contrast. The PT-D5600UL and PT-D5600U offer a brightness level of 6000 lumens, while the PT-DW5000U provides 5000 lumens, ensuring clear visibility even in well-lit rooms. This remarkable brightness coupled with a solid contrast ratio provides sharp and vivid images, whether for video presentations or intricate graphics.

The three models are equipped with a versatile lens system, which includes various optional lenses to accommodate different installation requirements. The lens shift feature enhances installation flexibility, allowing for simple adjustments to the image without distortion. The projectors support various resolutions and aspect ratios, including WUXGA (1920 x 1200) for the PT-D5600UL and PT-D5600U, and WXGA (1280 x 800) for the PT-DW5000U, ensuring that users can display content with high precision and clarity.

Panasonic’s innovative Daylight View technology enhances image quality by automatically adjusting color reproduction to match ambient lighting conditions, ensuring that images remain visible and consistent throughout the day. Furthermore, these projectors employ a durable lamp life of up to 3000 hours in normal mode, reducing maintenance needs and costs for users.

For enhanced connectivity, the PT-D5600UL, PT-D5600U, and PT-DW5000U are equipped with multiple input options, including HDMI, DVI-D, and VGA ports, supporting a range of multimedia devices. The projectors also support network monitoring and control via LAN, allowing users to manage settings and monitor performance remotely.

In terms of build quality, these projectors are designed for reliability and longevity. Their robust chassis and advanced cooling system ensure stable operation even during extended use, making them ideal for events or long presentations. Overall, the Panasonic PT-D5600UL, PT-D5600U, and PT-DW5000U projectors deliver a seamless and high-quality projection experience, solidifying Panasonic’s reputation as a leader in the projection technology market.
Top Page Image Contents