Panasonic PT-LW80NTU manual Lamp Power, Lamp Runtime, Power OFF Timer, Direct Power on, Auto Setup

Page 36

OPTION menu

Settings

LAMP POWER

You can adjust the power of the lamp to save electricity, prolong the lamp life and reduce the noise.

STANDARD When higher luminance is required ECO-MODEWhen lower luminance is sufficient

NOTE:

•When no input signal is detected, the function is disabled.

•The ECO-MODEsetting is recommended when higher luminance is not required such as in a small room.

LAMP RUNTIME

You can check how long the lamp has been used.

NOTE:

•LAMP RUNTIME is a relevant matter for lamp replacement timing. See “Replacing the Lamp unit” on page 44.

•When the lamp unit is replaced with the new unit, the setting need to be reset to “0”.

POWER OFF TIMER

You can set the off timer to switch off the power of the projector after a certain period of time automatically when no signal is detected. Press I H to select the required period from 15 to 60 minutes at intervals of 5 minutes.

DIRECT POWER ON

You can switch the projector start up status for when the electric power is supplied. Press I H to select the required option.

OFF

Starts in the same mode as last use.

ON

Skips the standby mode and starts

 

the projection.

NOTE:

•If the projector is started from the projecting mode, the POWER button pressing procedure is skippable.

AUTO SETUP

You can turn off the automatic AUTO SETUP adjustment system.

AUTO

When the projector detect a

 

COMPUTER signal, automatically

 

set the setting of POSITION, DOT

 

CLOCK and CLOCK PHASE in

 

POSITION menu.

BUTTON

Only when the AUTO SETUP button

 

is pressed, automatically set the

 

POSITION, DOT CLOCK and

 

CLOCK PHASE in POSITION menu

 

for COMPUTER signals. See

 

“Remote control” on page 14.

NOTE:

• AUTO setting is recommended.

SIGNAL SEARCH

You can turn off the auto signal detecting system.

ON

Detect the input signal from the

 

terminals and project the image.

OFF

Deactive

NOTE:

•SIGNAL SEARCH is not available when any input signal is projected.

INSTALLATION

When installing the projector, select the projection method according to the projector position. Press I H to cycle through the options. See “Projection method” on page 16.

FRONT/DESK

Setting on a desk/floor and

projecting from front

 

FRONT/CEILING

Mounting in the ceiling and

projecting from front

 

REAR/DESK

Setting on a desk/floor and

projecting from rear

 

REAR/CEILING

Mounting in the ceiling and

projecting from rear

 

CONTROL PANEL

You can turn off the function of the control panel buttons on the projector body. Press I H to select the required option.

VALID

Validate the control panel buttons

INVALID

Invalidate the control panel buttons

 

The confirmation screen will be

 

displayed.

ALTITUDE

If you use the projector at high elevation, the ALTITUDE setting need to be HIGH to set the fan speed high. Press I H to select the required option.

LOW

The fan speed is low.

HIGH

The fan speed is high.

NOTE:

•At 1 400 -2 700 m (4 593 - 8 858 ft) sea level, the setting must be HIGH.

•The loudness of fan noise depends on the ALTITUDE setting.

ENGLISH - 36

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Operating Instructions Important Safety Notice Dear Panasonic CustomerImportant Safety Notice Declaration of ConformityTrade Name PanasonicContents Settings MaintenanceContents AppendixPrecautions with regard to safety Precautions with regard to safety Do not set up the projector outdoorsDo not look into the lens while the projector is being used Lamp cover gets very hot, and touching it can cause burnsRemove the used batteries from the remote control promptly Do not put your weight on this projectorUse only the specified batteries Do not mix old and new batteriesSecurity Order to get the best picture qualityOptical components Liquid crystal panelAccessories K1HA15DA0002Minimum required setting screen Read this firstAbout Your Projector Projector bodyTop and front view Control panelRemote control signal receptor Lamp unit compartment About Your Projector Back and bottom viewRemote control Battery compartment Top viewAbout Your Projector Attaching a hand strapSetting up Screen size and throw distanceCalculation methods Front leg adjusters and throwing angle Setting upProjection method Mounting in the ceiling and projecting from frontConnecting example AV equipment Connecting example ComputersConnecting with Video IN/S-VIDEO ConnectionsSwitching the projector on/off Power cordConnecting Direct power off functionSwitching on the projector Switching the projector on/offBy control panel operation By remote control operation By direct power on functionSwitching off the projector By remote control operationBy direct power off function By control panel operationPower and Power Lock indicators Power Lock indicator statusPower indicator status Selecting the input signal Projecting an imagePositioning the image Remote control operation Setting up the image position automaticallyOperating range Facing to the projectorSwitching the input signal Resetting to the factory default settingsRemote control operation Capturing an imageProjecting an image in INDEX-WINDOW mode Using an assigned functionControlling the volume of the speaker Enlarging the centered area Enlarging the imageShifting the center point Press any side of the Digital Zoom +/- button onceMenu Navigation Navigating through the MenuStill Mode Main menu and Sub-menuMenu Navigation TV-SYSTEMClosed Caption Setting Picture menu Detailed Setup For S-VIDEO/VIDEO signalsFor RGB signals Position menu Image will be projected without any size adjustment AspectAspect ratio options 169Position menu Aspect ratio depend on signals Over ScanFrame Lock Screen Format menu OptionOption menu Lamp Power Power OFF TimerDirect Power on Auto SetupClosed Caption Setting Screen FormatTest Pattern Function ButtonAudio Balance Input Password Password ChangeSecurity menu Text DisplayText Change Security menuText Display Wireless menu Items in Wireless menuWireless menu, the following items are available Lamp and Temp Indicators Managing the indicated problemsLamp indicator Temp indicatorCare and Replacement Cleaning the projectorCare and Replacement When to replace the Lamp unitReplacing the Lamp unit Before replacing the lamp unitCare and Replacement Replacement procedure Resetting the Lamp RuntimeRemoving and replacing the lamp unit Troubleshooting List of compatible signals Technical InformationQuality*2 Dots*1 KHz MHzSerial terminal Technical Information Cable specifications Control commandsComputer connection guidance ProjectorSpecifications Video AudioComputer Audio Variable AudioScreen size and throw distance for 169/43 aspect ratio 169Calculation methods for Projection size 16 Throw distance LDimensions Trademark acknowledgementsUnit mm Index Position Power IndexAvis important concernant la sécurité Numéro de sérieAvis important concernant la sécurité AvertissementDéclaration de conformité Modèle nPrécautions de sécurité AvertissementsMises EN Garde Précautions de sécuritéNe pas obstruer les orifices dentrée et de sortie dair Ne pas utiliser le projecteur à lair libreRetirer les piles usées de la télécommande au plus vite Précautions lors du transportSinon cela peut causer des chocs électriques Utiliser uniquement les piles spécifiéesPrécautions lors de linstallation Précautions lors de lutilisationSécurité Affichage à cristaux liquidesRemplacement de lunité de la lampe Délai de remplacement de lUnité de la lampeAvant de remplacer le lunité de la lampe Retirer et remplacer la lampe Réinitialisation de Durée DE LA LampePanasonic Projector Systems Company Technical Support
Top Page Image Contents