Panasonic PT-LW80NTU manual Read this first, Minimum required setting screen

Page 11
When projector on a 16:10 or 4:3 screen.
When project on a 16:9 screen.

Read this first

Minimum required setting screen

When you start the projection for the first time or after the projector is initialized, the minimum required setting screen for projection will be displayed.

LANGUAGE

Select the required language setting.

LANGUAGE

ENGLISH

PLEASE SELECT LANGUAGE

SELECT

ENTER

Press F G I H buttons of the remote control or control panel on the projector to highlight the required language, and press the ENTER button to proceed to the next setting.

OPTION

Select the current projection method and fan speed setting. If you need return to the previous setting, press the RETURTN button.

OPTION

INSTALLATION

FRONT/DESK

 

 

 

 

SCREEN FORMAT

16:10

 

 

 

 

 

 

 

ALTITUDE

LOW

 

 

 

 

SWITCH TO HIGH ALTITUDE MODE "HIGH" IF OVER 1400m(4593Ft).

RETURN

SELECT

ENTER

INSTALLATION

Press I H buttons of the remote control or control panel on the projector to select the required installation method. Press G to proceed to the SCREEN FORMAT setting.

FRONT/DESK

Setting on a desk/floor and

projecting from front

 

FRONT/CEILING

Mounting in the ceiling and

projecting from front

 

REAR/DESK

Setting on a desk/floor and

projecting from rear

 

REAR/CEILING

Mounting in the ceiling and

projecting from rear

 

SCREEN FORMAT

Select the required screen format by pressing I H. Press G to proceed to the ALTITUDE setting.

16:10

16:9

ALTITUDE

If you use the projector at high elevation, the ALTITUDE setting need to be HIGH to set the fan speed high. Press I H to select the required option. If you need to return to the INSTALLATION, press F.

LOW

The fan speed is low.

HIGH

The fan speed is high.

NOTE:

At 1 400 - 2 700 m (4 593 - 8 858 ft) sea level, the setting must be HIGH.

The loudness of fan noise depends on the ALTITUDE setting.

Preparation

Press the ENTER button to start the projection.

Once you finish the minimum requirement setting, it will not be displayed again unless the projector is initialized. See “INITIALIZE ALL” on page 38.

You can change each settings in the main menu. See “Menu Navigation” on page 27.

ENGLISH - 11

Image 11
Contents Operating Instructions Dear Panasonic Customer Important Safety NoticePanasonic Important Safety NoticeDeclaration of Conformity Trade NameContents Appendix SettingsMaintenance ContentsPrecautions with regard to safety Lamp cover gets very hot, and touching it can cause burns Precautions with regard to safetyDo not set up the projector outdoors Do not look into the lens while the projector is being usedDo not mix old and new batteries Remove the used batteries from the remote control promptlyDo not put your weight on this projector Use only the specified batteriesLiquid crystal panel SecurityOrder to get the best picture quality Optical componentsK1HA15DA0002 AccessoriesRead this first Minimum required setting screenControl panel About Your ProjectorProjector body Top and front viewAbout Your Projector Back and bottom view Remote control signal receptor Lamp unit compartmentAttaching a hand strap Remote controlBattery compartment Top view About Your ProjectorCalculation methods Setting upScreen size and throw distance Mounting in the ceiling and projecting from front Front leg adjusters and throwing angleSetting up Projection methodConnections Connecting example AV equipmentConnecting example Computers Connecting with Video IN/S-VIDEODirect power off function Switching the projector on/offPower cord ConnectingBy direct power on function Switching on the projectorSwitching the projector on/off By control panel operation By remote control operationBy control panel operation Switching off the projectorBy remote control operation By direct power off functionPower indicator status Power and Power Lock indicatorsPower Lock indicator status Positioning the image Selecting the input signalProjecting an image Facing to the projector Remote control operationSetting up the image position automatically Operating rangeCapturing an image Switching the input signalResetting to the factory default settings Remote control operationControlling the volume of the speaker Projecting an image in INDEX-WINDOW modeUsing an assigned function Press any side of the Digital Zoom +/- button once Enlarging the centered areaEnlarging the image Shifting the center pointNavigating through the Menu Menu NavigationTV-SYSTEM Still ModeMain menu and Sub-menu Menu NavigationClosed Caption Setting Picture menu For RGB signals Detailed SetupFor S-VIDEO/VIDEO signals Position menu 169 Image will be projected without any size adjustmentAspect Aspect ratio optionsScreen Format menu Option Position menu Aspect ratio depend on signalsOver Scan Frame LockOption menu Auto Setup Lamp PowerPower OFF Timer Direct Power onFunction Button Closed Caption SettingScreen Format Test PatternAudio Balance Text Display Input PasswordPassword Change Security menuText Display Text ChangeSecurity menu Wireless menu, the following items are available Wireless menuItems in Wireless menu Temp indicator Lamp and Temp IndicatorsManaging the indicated problems Lamp indicatorCleaning the projector Care and ReplacementBefore replacing the lamp unit Care and ReplacementWhen to replace the Lamp unit Replacing the Lamp unitRemoving and replacing the lamp unit Care and Replacement Replacement procedureResetting the Lamp Runtime Troubleshooting Dots*1 KHz MHz List of compatible signalsTechnical Information Quality*2Serial terminal Projector Technical Information Cable specificationsControl commands Computer connection guidanceSpecifications Variable Audio VideoAudio Computer AudioProjection size 16 Throw distance L Screen size and throw distance for 169/43 aspect ratio169 Calculation methods forUnit mm DimensionsTrademark acknowledgements Index Index Position PowerNuméro de série Avis important concernant la sécuritéModèle n Avis important concernant la sécuritéAvertissement Déclaration de conformitéAvertissements Précautions de sécuritéNe pas utiliser le projecteur à lair libre Mises EN GardePrécautions de sécurité Ne pas obstruer les orifices dentrée et de sortie dairUtiliser uniquement les piles spécifiées Retirer les piles usées de la télécommande au plus vitePrécautions lors du transport Sinon cela peut causer des chocs électriquesAffichage à cristaux liquides Précautions lors de linstallationPrécautions lors de lutilisation SécuritéAvant de remplacer le lunité de la lampe Remplacement de lunité de la lampeDélai de remplacement de lUnité de la lampe Réinitialisation de Durée DE LA Lampe Retirer et remplacer la lampeTechnical Support Panasonic Projector Systems Company