Fujitsu warranty Using the Stylistic ST5000 Series Tablet PC, System States

Page 31

U s i n g Y o u r S t y l i s t i c S T 5 0 0 0

Using the Stylistic ST5000 Series Tablet PC

This chapter covers the fundamental concepts, basic system operation and use, and system functions of the Stylistic ST5000 Series Tablet PC. You should familiarize yourself with this information before you attempt to operate the system.

Prior to using your system, be sure to fully charge the battery if you plan to run on battery power. Failure to do so may result in erratic performance.

SYSTEM STATES

Before you begin using the Stylistic ST5000 Series Tablet PC, review the different system states (or modes) that the system can use. Being familiar with these states will help you determine whether it is appropriate to turn on, resume, suspend, hibernate or shut down the system when you begin or end a session. System behavior for each system state is described briefly in the following, with each system state listed in decreasing order of power usage:

•On state: The system is running and the display screen is on.

•Idle state: Some system functions are regulated or turned off to conserve power. The display screen may be turned off. The system returns to the On state when pen activity or other input is detected.

•Suspend-to-RAM mode (S3): System operation is suspended. Most system functions are turned off to conserve power. Power to memory is on, maintaining data in programs that were running before system operation was suspended. The system does not

respond to the pen or other input when in Suspend- to-RAM mode. Refer to the “Resuming System Operation” section later in this chapter for information on returning the system to the On state.

•Hibernate mode (Save-to-Disk) (S4): System operation is suspended. All system functions are turned off to conserve power. Active data in programs that were running before suspending system operation is stored on the hard disk drive. The system does not respond to the pen or other input. Refer to the “Resuming System Operation” section later in this chapter for information on returning the system to the On state.

•Off state: All system functions are turned off to conserve power. The system does not respond to the pen or other input. The system boots at the next system power-on.

The system consumes the same amount of power whether it is in Hibernate (Save-to- Disk) mode or the Off state.

Your system may be configured to enter some of these states automatically after a period of inactivity to conserve battery power.

When you use the Stylistic ST5000 Series Tablet PC, you can change the current system state in a number of ways, depending on the system’s current state. To determine the current system state, observe the Power icon in the Status display. Table 2-1 on page 22 gives the different system states represented by the Power icon and describes how you can change the system state from the current state.

21

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Declaration of Conformity Copyright and Trademark InformationPage Table of Contents Agency Notices Preface Page Fujitsu Contact Information Warranty InformationPreface About this GuidePage Getting Started with Your Stylistic ST5000 Series Tablet PC Page IN-BOX Items for the Stylistic ST5000 Series Tablet PC Getting Started with Your Stylistic Tablet PCOptional Accessories Swipe Sensor Stylistic Tablet PC FeaturesBack Features Top Features Left-Side Features Right-Side Features Icon Mode/State LED State Remarks Status DisplayHDD AccessDescription Tablet Button SettingsApplication Buttons Tablet IconApplication Buttons Primary and Secondary Functions Navigation Buttons Tertiary Functions of Application and Navigation Buttons Passwords Setting UP the Security PanelSecurity Functions of Application Buttons Precautions Using Your Security PanelUninstalling the Security Panel Application Open Add or Remove Programs Properties in the Control Panel Reinstalling the Security Panel ApplicationUser SupervisorConnector Tablet PC Purpose Peripheral Connectors and Peripheral InterfacesPeripheral Connectors/Interfaces Using Your Stylistic ST5000 Series Tablet PC Page System States Using the Stylistic ST5000 Series Tablet PCCurrent State To Change State Powering UP the Tablet PCShutting Down the System Suspending System OperationPower icon is not displayed Hibernate Save-to-Diskmode Power icon is blinking Suspend-to-RAMmodeSystem operation is suspended From Hibernate Save-to-Disk mode Adjusting the Display BrightnessUsing the PEN From Suspend-to-RAM modeCalibrating the PEN Installing a PEN TetherCharging the Battery Replacing the PEN TIP100% Removing and Installing the BatteryTips for Conserving Battery Power 90%Memory STICK/SD Card Slot Operation of the Bridge BatteryInstalling Memory Stick/SD Cards Modem ConnectionPC Card Slot Removing and Installing Memory ModulesRemoving a Memory Module Installing a Dimm ModulePage Care and Maintenance Page Caring for Your Tablet PC Care and MaintenanceProtecting the Display Screen Avoiding Overheating Cleaning the Display ScreenTroubleshooting Storing the Tablet PCRestoring Your PRE-INSTALLED Software Procedure Boot Priority ChangeRestoring the Factory Image Specifications Page Physical Specifications Stylistic ST5000 Series Hardware SpecificationsStylistic ST5000 Specifications Display SpecificationsAgency Approval Specifications Power SpecificationsAdditional Specifications Agency Notices Page FCC Notices Regulatory InformationAvis Aux Utilisateurs Du Réseau Téléphonique Canadien System Disposal UL NoticeAC Adapter output polarity For Authorized Repair Technicians OnlyPage Appendix a Page FCC Regulatory Information Wireless LAN Modes Using this Wireless Module Before Using the Wireless LANTypes of Wireless LANs Covered by this Document Characteristics of the Wireless ModuleHow to Handle This Wireless Module Access Point Infrastructure Mode See Figure A-2For Better Communications Starting Transmission Deactivation using the wireless switchDeactivation using Windows Stopping TransmissionAssigning parameters Connecting the WlanPreparation for Wireless LAN Connection Flow of OperationsClose the Wireless Network window Connection to the Network Setting the networkSetting TCP/IP Setting the sharing functionSetting the file-sharing function Setting the Microsoft network-sharing serviceSetting the printer-sharing function Confirming the status of the radio Confirming connectionCountry Transmit Power LevelPower Save Mode IP AddressSetting of channels during ad hoc connection Other settingsSetting of POWER-SAVING Function Setting of transmission power during ad hoc connectionConnection TroubleshootingUnavailable NetworkSoon after Access pointCommunication Is disconnectedWireless LAN Glossary Wi-Fi Open system authenticationShared key authentication Ssid Service Set IdentifierIP address information Specification SpecificationsWarranty Using the Bluetooth DeviceWhat is BLUETOOTH? Where to Find Information About BluetoothAppendix B Page Getting Started Installing OmnipassInstalling the OmniPass Application Introducing the Optional Fingerprint Sensor DeviceVerifying Information about OmniPass Uninstalling OmniPassMaster Password Concept User EnrollmentRemembering a Password Using OmnipassPassword Replacement OmniPass Authentication ToolbarLogging in to a Remembered Site Password ManagementExporting and Importing Users Configuring OmnipassIdentities and Password Management OmniPass User IdentitiesThings to Know Regarding Import/Export Omnipass Control CenterExporting an OmniPass User Profile Importing an OmniPass User ProfileSystem Settings User SettingsFirst option, Automatically log on to OmniPass as Cannot add Windows users to OmniPass Cannot add a User with a Blank Password to OmniPassEnabling the Security Chip in Bios Trusted Platform Module InstallationInstalling the TPM Applications ProcedurePage Index Adjusting the display brightness Air flow ventsMicrophone Microphone jack Storing the system unit Stylistic ST5000 Y l i s t i c S T 5 0 0 0 S e r i e s T a b l e t P C
Top Page Image Contents