Fujitsu ST5000 warranty Stopping Transmission, Starting Transmission, Deactivation using Windows

Page 62

S t y l i s t i c S T 5 0 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e – A p p e n d i x A

STOPPING TRANSMISSION

To use this product inside hospitals, clinics, or airplanes, or in other places where the use of electronic equipment is regulated, stop the transmission of radio waves from the wireless LAN beforehand.

Deactivation using the wireless switch

The transmission of radio waves from the wireless LAN can be stopped by setting the wireless switch to the Off position. Note that the wireless LAN On/Off switch has no effect on non-wireless LAN models.

(See Figure 3 for Wireless LAN switch location.)

Wireless LAN

On/Off

Switch

Figure A-3. Wireless LAN On/Off Switch

Deactivation using Windows

Intel PROSet Wireless LAN:

1.Click [Start] --> [(All) Programs] --> [Intel Net- work Adapters] --> [Intel(R) PROSet]. The Intel(R) PROSet window will be displayed.

2.Click the General tab.

3.Select [Off] for the wireless communications Switch Radio: function, and then click the [OK] button. Wireless communications on/off switching will be deactivated and the transmission of radio waves from the wireless LAN will be stopped.

To restart transmission, select [On] for the wireless communications Switch Radio: function, and then click the [OK] button.

Atheros Wireless LAN

1.Click [Start] --> [Control Panel] --> [Atheros Cli- ent Utility]. The Atheros Wireless Configuration Utility window will be displayed.

2.Click the Wireless Networks tab.

3.Click the [Enable Radio] box to clear it, then click the [OK] button. Wireless communications on/off switching will be deactivated and the transmission of radio waves from the wireless LAN will be stopped.

To restart transmission, check the [Enable Radio] checkbox to select it., then click the [OK] button.

STARTING TRANSMISSION

To communicate using the wireless LAN function, set the computer to a status from which it can transmit, as follows:

Intel PROSet Wireless LAN:

1.Set the wireless switch to the On position.

2.Click [Start] --> [(All) Programs] --> [Intel Net- work Adapters] --> [Intel(R) PROSet]. The Intel(R) PROSet window will be displayed.

3.Click the [General] tab if it is not already selected.

4.Select [ON] for the Switch radio: function, then click [OK]. Wireless communications on/off switching will be activated and the transmission of radio waves will be restarted.

Atheros Wireless LAN:

1.Click the Wireless Network Connection icon in the system tray at the lower right of your screen.

2.Click [Enable Radio]. The radio will be turned on. Access Point Mode: Transmission is enabled.

Ad Hoc Mode: Restart your computer to enable the radio.

52

Page 61 Page 63
Image 62
Page 61 Page 63
Contents Copyright and Trademark Information Declaration of ConformityPage Table of Contents Agency Notices Preface Page About this Guide Warranty InformationPreface Fujitsu Contact InformationPage Getting Started with Your Stylistic ST5000 Series Tablet PC Page Getting Started with Your Stylistic Tablet PC IN-BOX Items for the Stylistic ST5000 Series Tablet PCOptional Accessories Stylistic Tablet PC Features Swipe SensorBack Features Top Features Left-Side Features Right-Side Features Status Display Icon Mode/State LED State RemarksAccess HDDTablet Icon Tablet Button SettingsApplication Buttons DescriptionApplication Buttons Primary and Secondary Functions Navigation Buttons Tertiary Functions of Application and Navigation Buttons Security Functions of Application Buttons Setting UP the Security PanelPasswords Uninstalling the Security Panel Application Using Your Security PanelPrecautions Supervisor Reinstalling the Security Panel ApplicationUser Open Add or Remove Programs Properties in the Control PanelConnectors and Peripheral Interfaces Connector Tablet PC Purpose PeripheralPeripheral Connectors/Interfaces Using Your Stylistic ST5000 Series Tablet PC Page Using the Stylistic ST5000 Series Tablet PC System StatesSuspending System Operation Powering UP the Tablet PCShutting Down the System Current State To Change StateSystem operation is suspended Power icon is blinking Suspend-to-RAMmodePower icon is not displayed Hibernate Save-to-Diskmode From Suspend-to-RAM mode Adjusting the Display BrightnessUsing the PEN From Hibernate Save-to-Disk modeReplacing the PEN TIP Installing a PEN TetherCharging the Battery Calibrating the PEN90% Removing and Installing the BatteryTips for Conserving Battery Power 100%Modem Connection Operation of the Bridge BatteryInstalling Memory Stick/SD Cards Memory STICK/SD Card SlotRemoving and Installing Memory Modules PC Card SlotInstalling a Dimm Module Removing a Memory ModulePage Care and Maintenance Page Protecting the Display Screen Care and MaintenanceCaring for Your Tablet PC Storing the Tablet PC Cleaning the Display ScreenTroubleshooting Avoiding OverheatingRestoring Your PRE-INSTALLED Software Restoring the Factory Image Boot Priority ChangeProcedure Specifications Page Display Specifications Stylistic ST5000 Series Hardware SpecificationsStylistic ST5000 Specifications Physical SpecificationsAdditional Specifications Power SpecificationsAgency Approval Specifications Agency Notices Page Regulatory Information FCC NoticesAvis Aux Utilisateurs Du Réseau Téléphonique Canadien For Authorized Repair Technicians Only UL NoticeAC Adapter output polarity System DisposalPage Appendix a Page FCC Regulatory Information Characteristics of the Wireless Module Before Using the Wireless LANTypes of Wireless LANs Covered by this Document Wireless LAN Modes Using this Wireless ModuleFor Better Communications Access Point Infrastructure Mode See Figure A-2How to Handle This Wireless Module Stopping Transmission Deactivation using the wireless switchDeactivation using Windows Starting TransmissionFlow of Operations Connecting the WlanPreparation for Wireless LAN Connection Assigning parametersClose the Wireless Network window Setting the sharing function Setting the networkSetting TCP/IP Connection to the NetworkSetting the printer-sharing function Setting the Microsoft network-sharing serviceSetting the file-sharing function Confirming connection Confirming the status of the radioIP Address Transmit Power LevelPower Save Mode CountrySetting of transmission power during ad hoc connection Other settingsSetting of POWER-SAVING Function Setting of channels during ad hoc connectionNetwork TroubleshootingUnavailable ConnectionIs disconnected Access pointCommunication Soon afterWireless LAN Glossary Ssid Service Set Identifier Open system authenticationShared key authentication Wi-FiIP address information Specifications SpecificationWhere to Find Information About Bluetooth Using the Bluetooth DeviceWhat is BLUETOOTH? WarrantyAppendix B Page Introducing the Optional Fingerprint Sensor Device Installing OmnipassInstalling the OmniPass Application Getting StartedUser Enrollment Uninstalling OmniPassMaster Password Concept Verifying Information about OmniPassOmniPass Authentication Toolbar Using OmnipassPassword Replacement Remembering a PasswordPassword Management Logging in to a Remembered SiteOmniPass User Identities Configuring OmnipassIdentities and Password Management Exporting and Importing UsersImporting an OmniPass User Profile Omnipass Control CenterExporting an OmniPass User Profile Things to Know Regarding Import/ExportFirst option, Automatically log on to OmniPass as User SettingsSystem Settings Cannot add a User with a Blank Password to OmniPass Cannot add Windows users to OmniPassProcedure Trusted Platform Module InstallationInstalling the TPM Applications Enabling the Security Chip in BiosPage Adjusting the display brightness Air flow vents IndexMicrophone Microphone jack Storing the system unit Stylistic ST5000 Y l i s t i c S T 5 0 0 0 S e r i e s T a b l e t P C
Top Page Image Contents