Fujitsu ST5000 warranty Restoring the Factory Image, Boot Priority Change, Procedure

Page 46

S t y l i s t i c S T 5 0 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e – S e c t i o n T h r e e

2.After reading the License Agreement, click [I agree].

3.A window will appear containing a list of applica- tions, drivers, and utilities that you can install from the Drivers and Applications CD.

The components listed are color-coded in terms of their install status. Blue indicates that the component can be installed. Green indicates that the component needs to be installed separately. Grey indicates a component that is already installed; grey items can be reinstalled, but prior to installation you will receive a reminder that the component is already installed.

4.In the list, check off all the components you want to install. If you want to install all components, click [Select All]. Clicking [Select All] will select all of the blue-coded components; you must select grey and green components separately.

5.Once you have selected the components you wish to install, click [Install Selected Subsystems]; the components will be installed.

6.After the components are installed, click [OK], then click [Yes] when asked if you want to reboot the system.

RESTORING THE FACTORY IMAGE

The Restore Disc that came with your system contains two utilities:

■The Recovery utility allows you to restore the original contents of the C: drive.

■The Hard Disk Data Delete utility on this disc is used to delete all data on your hard disk and prevent it from being reused. Do not use the Hard Disk Data Delete utility unless you are absolutely certain that you want to erase your entire hard disk, including all partitions.

•The use of this disc requires that you have a device capable of reading DVDs attached to your system. If you do not have a built-in DVD player, you will need to attach an external player. For more information on available external devices, visit our Web site at: us.fujitsu.com/computers.

•This disc can only be used with the system with which it was purchased.

BOOT Priority Change

Before restoring an image, you must first verify that your system is set up to boot from the DVD drive. To verify/ change the boot-up priority (rather than booting-up from the hard drive or an external floppy disk drive), perform the following steps:

1.Start your system and press the [Ctl-Alt-Del] appli- cation button or the [F2] key on a keyboard when the Fujitsu logo appears. You will enter the BIOS Setup Utility.

2.Using the arrow keys, go to the Boot menu.

3.Arrow down to the Boot Device Priority submenu. Press [Enter].

4.If “Optical Media Drive” or “CD-ROM Drive” is not at the top of the list, arrow down to the drive in the list, and press the space bar (or the + key) to move it to the top of the list. (The system attempts to boot from the devices in the order in which they are listed.). Note that the BIOS for some systems will indicate “CD-ROM Drive”, even when a DVD drive is connected.

5.If you have an external DVD drive connected, proceed to the next step; otherwise, proceed to step 7.

6.If you have an external DVD drive connected:

•Select the Advanced menu in the BIOS window.

•Scroll down to the USB Features submenu and press the Enter key to open it.

•If Legacy USB Support is disabled, press the space bar to enable it.

•Scroll down to SCSI SubClass Support and press the space bar to enable it.

7.Press [F10], then click on [Yes] to exit the BIOS Setup Utility and return to the boot process.

After you have changed the boot priority, you can restore a backup image when you are booting up.

Procedure

1.Turn on the power to your system.

2.Ensure that you have a device that can read DVDs either installed in your system or attached exter- nally to it.

3.Insert the Restore Disc into the drive tray.

4.Reboot your system.

5.After the system reboots, follow the instructions that appear to either restore your system image or erase all data from your hard disk.

36

Page 45 Page 47
Image 46
Page 45 Page 47
Contents Copyright and Trademark Information Declaration of ConformityPage Table of Contents Agency Notices Preface Page About this Guide Warranty InformationPreface Fujitsu Contact InformationPage Getting Started with Your Stylistic ST5000 Series Tablet PC Page Getting Started with Your Stylistic Tablet PC IN-BOX Items for the Stylistic ST5000 Series Tablet PCOptional Accessories Stylistic Tablet PC Features Swipe SensorBack Features Top Features Left-Side Features Right-Side Features Status Display Icon Mode/State LED State RemarksAccess HDDTablet Icon Tablet Button SettingsApplication Buttons DescriptionApplication Buttons Primary and Secondary Functions Navigation Buttons Tertiary Functions of Application and Navigation Buttons Passwords Setting UP the Security PanelSecurity Functions of Application Buttons Precautions Using Your Security PanelUninstalling the Security Panel Application Supervisor Reinstalling the Security Panel ApplicationUser Open Add or Remove Programs Properties in the Control PanelConnectors and Peripheral Interfaces Connector Tablet PC Purpose PeripheralPeripheral Connectors/Interfaces Using Your Stylistic ST5000 Series Tablet PC Page Using the Stylistic ST5000 Series Tablet PC System StatesSuspending System Operation Powering UP the Tablet PCShutting Down the System Current State To Change StatePower icon is not displayed Hibernate Save-to-Diskmode Power icon is blinking Suspend-to-RAMmodeSystem operation is suspended From Suspend-to-RAM mode Adjusting the Display BrightnessUsing the PEN From Hibernate Save-to-Disk modeReplacing the PEN TIP Installing a PEN TetherCharging the Battery Calibrating the PEN90% Removing and Installing the BatteryTips for Conserving Battery Power 100%Modem Connection Operation of the Bridge BatteryInstalling Memory Stick/SD Cards Memory STICK/SD Card SlotRemoving and Installing Memory Modules PC Card SlotInstalling a Dimm Module Removing a Memory ModulePage Care and Maintenance Page Caring for Your Tablet PC Care and MaintenanceProtecting the Display Screen Storing the Tablet PC Cleaning the Display ScreenTroubleshooting Avoiding OverheatingRestoring Your PRE-INSTALLED Software Procedure Boot Priority ChangeRestoring the Factory Image Specifications Page Display Specifications Stylistic ST5000 Series Hardware SpecificationsStylistic ST5000 Specifications Physical SpecificationsAgency Approval Specifications Power SpecificationsAdditional Specifications Agency Notices Page Regulatory Information FCC NoticesAvis Aux Utilisateurs Du Réseau Téléphonique Canadien For Authorized Repair Technicians Only UL NoticeAC Adapter output polarity System DisposalPage Appendix a Page FCC Regulatory Information Characteristics of the Wireless Module Before Using the Wireless LANTypes of Wireless LANs Covered by this Document Wireless LAN Modes Using this Wireless ModuleHow to Handle This Wireless Module Access Point Infrastructure Mode See Figure A-2For Better Communications Stopping Transmission Deactivation using the wireless switchDeactivation using Windows Starting TransmissionFlow of Operations Connecting the WlanPreparation for Wireless LAN Connection Assigning parametersClose the Wireless Network window Setting the sharing function Setting the networkSetting TCP/IP Connection to the NetworkSetting the file-sharing function Setting the Microsoft network-sharing serviceSetting the printer-sharing function Confirming connection Confirming the status of the radioIP Address Transmit Power LevelPower Save Mode CountrySetting of transmission power during ad hoc connection Other settingsSetting of POWER-SAVING Function Setting of channels during ad hoc connectionNetwork TroubleshootingUnavailable ConnectionIs disconnected Access pointCommunication Soon afterWireless LAN Glossary Ssid Service Set Identifier Open system authenticationShared key authentication Wi-FiIP address information Specifications SpecificationWhere to Find Information About Bluetooth Using the Bluetooth DeviceWhat is BLUETOOTH? WarrantyAppendix B Page Introducing the Optional Fingerprint Sensor Device Installing OmnipassInstalling the OmniPass Application Getting StartedUser Enrollment Uninstalling OmniPassMaster Password Concept Verifying Information about OmniPassOmniPass Authentication Toolbar Using OmnipassPassword Replacement Remembering a PasswordPassword Management Logging in to a Remembered SiteOmniPass User Identities Configuring OmnipassIdentities and Password Management Exporting and Importing UsersImporting an OmniPass User Profile Omnipass Control CenterExporting an OmniPass User Profile Things to Know Regarding Import/ExportSystem Settings User SettingsFirst option, Automatically log on to OmniPass as Cannot add a User with a Blank Password to OmniPass Cannot add Windows users to OmniPassProcedure Trusted Platform Module InstallationInstalling the TPM Applications Enabling the Security Chip in BiosPage Adjusting the display brightness Air flow vents IndexMicrophone Microphone jack Storing the system unit Stylistic ST5000 Y l i s t i c S T 5 0 0 0 S e r i e s T a b l e t P C
Top Page Image Contents