Fujitsu ST5000 warranty PC Card Slot, Removing and Installing Memory Modules

Page 38

S t y l i s t i c S T 5 0 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e – S e c t i o n T w o

1.See your Memory Stick or SD Card manual for instructions on the installation of your card. Some cards may require that your system is off while installing them.

2.Make sure there is no card currently in the slot. If there is, see Removing a Memory Stick/SD Card.

3.Insert your card into the slot with the product label facing up.

4.Push the card firmly into the slot until it is seated in the connector.

Removing A Memory Stick/SD Card

To remove a Memory Stick or SD Card, follow these easy steps:

See your Memory Stick or SD Card manual for specific instructions on the removal of your card. Some cards may require your computer to be in Suspend Mode or Off while removing them.

Push the Memory Stick or SD Card in until it unlatches. It will then eject from the slot for removal

PC CARD SLOT

The Stylistic ST5000 Series Tablet PC Card slot allows you to install a Type I or Type II PCMCIA Card.

Installing a PC Card

To install a PC card, position the side with the arrow facing up (i.e., when looking at the tablet’s display side, the arrow on the card should be visible.) Slide the card into the PC Card slot, and press it firmly to ensure proper seating. (See Figure 2-6 for location)

If you need assistance installing a PC Card in the Stylistic ST5000 Series Tablet PC, contact your corporate help desk or reseller.

Figure 2-6. Installing a PC Card

Removing a PC Card

To remove a PC Card, first click the Safely Remove Hardware icon in the system tray in the bottom right- hand corner of the display. Select PC Card from the list, and click [Stop].

Press the PC Card eject button so that it pops out. Once the button has popped out, press it firmly to eject the card. (See Figure 2-7 for location)

Figure 2-7. Removing a PC Card

REMOVING AND INSTALLING

MEMORY MODULES

There are two DIMM slots in your Tablet PC. 256 MB, 512 MB, and 1 GB modules are available, so you can install a combination of up to 2 GB in the system.

DIMM replacement should be performed at a static-free workstation. Do not touch connector pins, circuit boards, or other circuit components on the drive or Tablet PC. Electrostatic discharge caused by doing so can damage sensitive components.

Installing a Memory Module

To install a DIMM module in the Tablet PC:

1.Ensure that the Tablet PC is off. To do so, carry out the Shut Down command in the Start menu. (Do not attempt to remove or install a DIMM module when the system is in Suspend mode or running.)

2.Remove the two screws from the cover plate on the back of the Tablet PC and remove the cover plate as shown in Figure 2-8.

Figure 2-8. Accessing the Memory Slot

28

Image 38
Contents Copyright and Trademark Information Declaration of ConformityPage Table of Contents Agency Notices Preface Page About this Guide Warranty InformationPreface Fujitsu Contact InformationPage Getting Started with Your Stylistic ST5000 Series Tablet PC Page Getting Started with Your Stylistic Tablet PC IN-BOX Items for the Stylistic ST5000 Series Tablet PCOptional Accessories Stylistic Tablet PC Features Swipe SensorBack Features Top Features Left-Side Features Right-Side Features Status Display Icon Mode/State LED State RemarksAccess HDDTablet Icon Tablet Button SettingsApplication Buttons DescriptionApplication Buttons Primary and Secondary Functions Navigation Buttons Tertiary Functions of Application and Navigation Buttons Security Functions of Application Buttons Setting UP the Security PanelPasswords Uninstalling the Security Panel Application Using Your Security PanelPrecautions Supervisor Reinstalling the Security Panel ApplicationUser Open Add or Remove Programs Properties in the Control PanelConnectors and Peripheral Interfaces Connector Tablet PC Purpose PeripheralPeripheral Connectors/Interfaces Using Your Stylistic ST5000 Series Tablet PC Page Using the Stylistic ST5000 Series Tablet PC System StatesSuspending System Operation Powering UP the Tablet PCShutting Down the System Current State To Change StateSystem operation is suspended Power icon is blinking Suspend-to-RAMmodePower icon is not displayed Hibernate Save-to-Diskmode From Suspend-to-RAM mode Adjusting the Display BrightnessUsing the PEN From Hibernate Save-to-Disk modeReplacing the PEN TIP Installing a PEN TetherCharging the Battery Calibrating the PEN90% Removing and Installing the BatteryTips for Conserving Battery Power 100%Modem Connection Operation of the Bridge BatteryInstalling Memory Stick/SD Cards Memory STICK/SD Card SlotRemoving and Installing Memory Modules PC Card SlotInstalling a Dimm Module Removing a Memory ModulePage Care and Maintenance Page Protecting the Display Screen Care and MaintenanceCaring for Your Tablet PC Storing the Tablet PC Cleaning the Display ScreenTroubleshooting Avoiding OverheatingRestoring Your PRE-INSTALLED Software Restoring the Factory Image Boot Priority ChangeProcedure Specifications Page Display Specifications Stylistic ST5000 Series Hardware SpecificationsStylistic ST5000 Specifications Physical SpecificationsAdditional Specifications Power SpecificationsAgency Approval Specifications Agency Notices Page Regulatory Information FCC NoticesAvis Aux Utilisateurs Du Réseau Téléphonique Canadien For Authorized Repair Technicians Only UL NoticeAC Adapter output polarity System DisposalPage Appendix a Page FCC Regulatory Information Characteristics of the Wireless Module Before Using the Wireless LANTypes of Wireless LANs Covered by this Document Wireless LAN Modes Using this Wireless ModuleFor Better Communications Access Point Infrastructure Mode See Figure A-2How to Handle This Wireless Module Stopping Transmission Deactivation using the wireless switchDeactivation using Windows Starting TransmissionFlow of Operations Connecting the WlanPreparation for Wireless LAN Connection Assigning parametersClose the Wireless Network window Setting the sharing function Setting the networkSetting TCP/IP Connection to the NetworkSetting the printer-sharing function Setting the Microsoft network-sharing serviceSetting the file-sharing function Confirming connection Confirming the status of the radioIP Address Transmit Power LevelPower Save Mode CountrySetting of transmission power during ad hoc connection Other settingsSetting of POWER-SAVING Function Setting of channels during ad hoc connectionNetwork TroubleshootingUnavailable ConnectionIs disconnected Access pointCommunication Soon afterWireless LAN Glossary Ssid Service Set Identifier Open system authenticationShared key authentication Wi-FiIP address information Specifications SpecificationWhere to Find Information About Bluetooth Using the Bluetooth DeviceWhat is BLUETOOTH? WarrantyAppendix B Page Introducing the Optional Fingerprint Sensor Device Installing OmnipassInstalling the OmniPass Application Getting StartedUser Enrollment Uninstalling OmniPassMaster Password Concept Verifying Information about OmniPassOmniPass Authentication Toolbar Using OmnipassPassword Replacement Remembering a PasswordPassword Management Logging in to a Remembered SiteOmniPass User Identities Configuring OmnipassIdentities and Password Management Exporting and Importing UsersImporting an OmniPass User Profile Omnipass Control CenterExporting an OmniPass User Profile Things to Know Regarding Import/ExportFirst option, Automatically log on to OmniPass as User SettingsSystem Settings Cannot add a User with a Blank Password to OmniPass Cannot add Windows users to OmniPassProcedure Trusted Platform Module InstallationInstalling the TPM Applications Enabling the Security Chip in BiosPage Adjusting the display brightness Air flow vents IndexMicrophone Microphone jack Storing the system unit Stylistic ST5000 Y l i s t i c S T 5 0 0 0 S e r i e s T a b l e t P C