Fujitsu Stylistic ST5000 Series Hardware Specifications, Stylistic ST5000 Specifications

Page 49

S y s t e m S p e c i f i c a t i o n s

Stylistic ST5000 Series Hardware Specifications

The following table provides general hardware specifica- tions of the Stylistic ST5000 Series Tablet PC by category.

 

Stylistic ST5000 Specifications

 

 

 

 

 

Processing Specifications

 

 

 

CPU

 

Intel® Pentium® M Processor ULV

 

 

733*

 

 

 

Chip set

 

Intel 855GME - 400 MHz FSB

 

 

 

Processor

 

1.1 GHz*

Speed

 

 

 

 

 

 

 

Memory/Storage Specifications

 

 

 

Main RAM

 

• 2 DIMM slots available

 

 

200-pin SO DIMM modules

 

 

• 256 MB, 512 MB, and 1 GB

 

 

 

module configurations available,

 

 

 

with a system maximum of 2 GB.

 

 

 

L1 cache

 

32 KB on-die

(CPU)

 

 

 

 

 

 

L2 cache

 

2 MB on-die

 

 

 

BIOS ROM

 

1 MB (FWH)

 

 

 

 

Hard disk

 

2.5” HDD

drive

 

Minimum 40 GB IDE HDD*

 

 

ATA 100

 

 

4200 or 5400 rpm*

 

 

Shock-mounted

 

 

 

 

Display Specifications

Depending on the configuration of your system, it has either a 12.1" transmissive or a 10.4" reflective display

12.1"

Transmissive Color LCD

Display

Active Digitizer

16-bit color

12.1” TFT XGA (1024 x 768), 16M colors

Brightness: 8 levels

Viewing Angle:

Horizontal: 80 degrees (min.) Vertical: 80 degrees (min.)

Contrast Ratio: Typ. 250, Min. 100

*The specifications for your particular model may vary. To determine the specifications for your system, please visit our Web site at: http://us.fujitsu.com/computers.

Stylistic ST5000 Specifications (Continued)

10.4"

Reflective Color LCD

Display

Active Digitizer

 

Outdoor-viewable

 

16-bit color

 

• 10.4” TFT XGA (1024 x 768),

 

 

16M colors

 

Brightness: 8 levels

 

 

VRAM

Intel 855GME chipset with 8MB

 

shared memory using Unified Memory

 

Architecture (UMA) delivers low-

 

power, high-performance 3D/2D

 

graphics, video, and display

 

capabilities. Dynamic Video Memory

 

Technology (DVMT) dynamically

 

responds to application requirements

 

and efficiently allocates the proper

 

amount of memory (64 MB max.) for

 

optimal graphics and system

 

performance.

 

 

 

Physical Specifications

 

 

Dimensions

12.1" Display (Active Digitizer):

 

8.66" w x 12.77" d x 0.82"-0.88" h

 

(220 mm x 324.4 mm x 20.9-22.3

 

mm)

 

10.4" Display (Reflective Digitizer):

 

8.66" x 12.76" x 0.91"-0.98"

 

(220 mm x 324.1 mm x 23.0-24.9

 

mm)

 

 

Weight

3.5 lbs. (1.59 Kg) (with battery)

 

 

 

Interface Specifications

 

 

 

Card Slots

PCMCIA: One Type I or Type II,

 

 

PCMCIA CardBus version 3.0

 

Secure Digital (SD)/

 

 

Memory Stick slot

 

Smart Card slot

 

 

 

Integrated

Modem (RJ-11)

Interfaces

LAN (RJ-45)

 

• IEEE 1394 (S400 4-pin)

 

• USB 2.0 (Qty. 2)

 

DC-In

 

IrDA

 

15-pin D-SUB connector for

 

 

external VGA monitor

 

Docking connector

 

 

Infrared

IrDA version 1.1 (FIR, 4Mbps)

 

 

 

39

Image 49
Contents Declaration of Conformity Copyright and Trademark InformationPage Table of Contents Agency Notices Preface Page Preface Warranty InformationAbout this Guide Fujitsu Contact InformationPage Getting Started with Your Stylistic ST5000 Series Tablet PC Page IN-BOX Items for the Stylistic ST5000 Series Tablet PC Getting Started with Your Stylistic Tablet PCOptional Accessories Swipe Sensor Stylistic Tablet PC FeaturesBack Features Top Features Left-Side Features Right-Side Features Icon Mode/State LED State Remarks Status DisplayHDD AccessApplication Buttons Tablet Button SettingsTablet Icon DescriptionApplication Buttons Primary and Secondary Functions Navigation Buttons Tertiary Functions of Application and Navigation Buttons Passwords Setting UP the Security PanelSecurity Functions of Application Buttons Precautions Using Your Security PanelUninstalling the Security Panel Application User Reinstalling the Security Panel ApplicationSupervisor Open Add or Remove Programs Properties in the Control PanelConnector Tablet PC Purpose Peripheral Connectors and Peripheral InterfacesPeripheral Connectors/Interfaces Using Your Stylistic ST5000 Series Tablet PC Page System States Using the Stylistic ST5000 Series Tablet PCShutting Down the System Powering UP the Tablet PCSuspending System Operation Current State To Change StatePower icon is not displayed Hibernate Save-to-Diskmode Power icon is blinking Suspend-to-RAMmodeSystem operation is suspended Using the PEN Adjusting the Display BrightnessFrom Suspend-to-RAM mode From Hibernate Save-to-Disk modeCharging the Battery Installing a PEN TetherReplacing the PEN TIP Calibrating the PENTips for Conserving Battery Power Removing and Installing the Battery90% 100%Installing Memory Stick/SD Cards Operation of the Bridge BatteryModem Connection Memory STICK/SD Card SlotPC Card Slot Removing and Installing Memory ModulesRemoving a Memory Module Installing a Dimm ModulePage Care and Maintenance Page Caring for Your Tablet PC Care and MaintenanceProtecting the Display Screen Troubleshooting Cleaning the Display ScreenStoring the Tablet PC Avoiding OverheatingRestoring Your PRE-INSTALLED Software Procedure Boot Priority ChangeRestoring the Factory Image Specifications Page Stylistic ST5000 Specifications Stylistic ST5000 Series Hardware SpecificationsDisplay Specifications Physical SpecificationsAgency Approval Specifications Power SpecificationsAdditional Specifications Agency Notices Page FCC Notices Regulatory InformationAvis Aux Utilisateurs Du Réseau Téléphonique Canadien AC Adapter output polarity UL NoticeFor Authorized Repair Technicians Only System DisposalPage Appendix a Page FCC Regulatory Information Types of Wireless LANs Covered by this Document Before Using the Wireless LANCharacteristics of the Wireless Module Wireless LAN Modes Using this Wireless ModuleHow to Handle This Wireless Module Access Point Infrastructure Mode See Figure A-2For Better Communications Deactivation using Windows Deactivation using the wireless switchStopping Transmission Starting TransmissionPreparation for Wireless LAN Connection Connecting the WlanFlow of Operations Assigning parametersClose the Wireless Network window Setting TCP/IP Setting the networkSetting the sharing function Connection to the NetworkSetting the file-sharing function Setting the Microsoft network-sharing serviceSetting the printer-sharing function Confirming the status of the radio Confirming connectionPower Save Mode Transmit Power LevelIP Address CountrySetting of POWER-SAVING Function Other settingsSetting of transmission power during ad hoc connection Setting of channels during ad hoc connectionUnavailable TroubleshootingNetwork ConnectionCommunication Access pointIs disconnected Soon afterWireless LAN Glossary Shared key authentication Open system authenticationSsid Service Set Identifier Wi-FiIP address information Specification SpecificationsWhat is BLUETOOTH? Using the Bluetooth DeviceWhere to Find Information About Bluetooth WarrantyAppendix B Page Installing the OmniPass Application Installing OmnipassIntroducing the Optional Fingerprint Sensor Device Getting StartedMaster Password Concept Uninstalling OmniPassUser Enrollment Verifying Information about OmniPassPassword Replacement Using OmnipassOmniPass Authentication Toolbar Remembering a PasswordLogging in to a Remembered Site Password ManagementIdentities and Password Management Configuring OmnipassOmniPass User Identities Exporting and Importing UsersExporting an OmniPass User Profile Omnipass Control CenterImporting an OmniPass User Profile Things to Know Regarding Import/ExportSystem Settings User SettingsFirst option, Automatically log on to OmniPass as Cannot add Windows users to OmniPass Cannot add a User with a Blank Password to OmniPassInstalling the TPM Applications Trusted Platform Module InstallationProcedure Enabling the Security Chip in BiosPage Index Adjusting the display brightness Air flow ventsMicrophone Microphone jack Storing the system unit Stylistic ST5000 Y l i s t i c S T 5 0 0 0 S e r i e s T a b l e t P C