Fujitsu ST5000 warranty Security Functions of Application Buttons, Setting UP the Security Panel

Page 24

S t y l i s t i c S T 5 0 0 0 S e r i e s T a b l e t P C U s e r ’ s G u i d e – S e c t i o n O n e

SECURITY FUNCTIONS OF APPLICATION BUTTONS

Five buttons are used when implementing security functions. Four of the buttons are used to enter the password, and the fifth is used as an Enter button. Instructions for using the security feature follow the table.

Button Icons

Security Icons

Security Purpose

 

 

 

 

 

 

 

Security Enter Button

 

 

 

Ctl-Alt-Del Button

 

 

 

 

 

 

 

 

 

1

Security Button 1

EMail Button

 

 

 

 

 

 

 

 

2

Security Button 2

Orientation Button

 

 

 

 

 

 

Escape Button

3

Security Button 3

 

 

 

 

 

 

Enter Button

4

Security Button 4

 

 

 

 

 

 

 

Table 1-6. Security Functions of Application Buttons

SETTING UP THE SECURITY PANEL

When you receive your Tablet PC, the security panel application is pre-installed without any passwords. The following sections provide detailed information on your security panel, how to set, change or remove passwords.

Numbered Buttons

Use these buttons to enter your password.(Figure 1-6)

Enter Button

After entering the button strokes, push this button to enter the password into the Tablet PC. (Figure 1-6)

PASSWORDS

The user and supervisor password may be set on this Tablet PC. A supervisor password is typically the same for all Tablet PC’s and notebooks in a work group, office, or company to allow for system management. Individual computers in a group environment should not use a common password. A password consists of one to five button strokes plus the enter button. A valid stroke consists of pushing one or up to four buttons simulta- neously.

The following are valid button strokes:

Pushing [4] by itself

Pushing [2] and [3] at the same time

Pushing [1], [2], and [4] at the same time

Pushing [1], [2], [3], and [4] at the same time

The following are valid passwords. The numbers within braces ({ }) are button strokes using more than one button.

{[2]+[3]}, [1], [Enter]

[4], [enter]

{[1]+[3]}, {[2]+[3]+[4]}, [1], [4], [2], [Enter]

Setting Passwords

When shipped from the factory, no passwords are set. You have a choice of having no password or setting a supervisor and user password. You must set the super- visor password before the user password.

The purpose of supervisor password is to be able to bypass the user password in case the user password is forgotten. The supervisor password alone will not lock the system.

You must set the supervisor and user passwords for the security panel to work.

14

Image 24
Contents Copyright and Trademark Information Declaration of ConformityPage Table of Contents Agency Notices Preface Page Warranty Information PrefaceAbout this Guide Fujitsu Contact InformationPage Getting Started with Your Stylistic ST5000 Series Tablet PC Page Getting Started with Your Stylistic Tablet PC IN-BOX Items for the Stylistic ST5000 Series Tablet PCOptional Accessories Stylistic Tablet PC Features Swipe SensorBack Features Top Features Left-Side Features Right-Side Features Status Display Icon Mode/State LED State RemarksAccess HDDTablet Button Settings Application ButtonsTablet Icon DescriptionApplication Buttons Primary and Secondary Functions Navigation Buttons Tertiary Functions of Application and Navigation Buttons Setting UP the Security Panel PasswordsSecurity Functions of Application Buttons Using Your Security Panel PrecautionsUninstalling the Security Panel Application Reinstalling the Security Panel Application UserSupervisor Open Add or Remove Programs Properties in the Control PanelConnectors and Peripheral Interfaces Connector Tablet PC Purpose PeripheralPeripheral Connectors/Interfaces Using Your Stylistic ST5000 Series Tablet PC Page Using the Stylistic ST5000 Series Tablet PC System StatesPowering UP the Tablet PC Shutting Down the SystemSuspending System Operation Current State To Change StatePower icon is blinking Suspend-to-RAMmode Power icon is not displayed Hibernate Save-to-DiskmodeSystem operation is suspended Adjusting the Display Brightness Using the PENFrom Suspend-to-RAM mode From Hibernate Save-to-Disk modeInstalling a PEN Tether Charging the BatteryReplacing the PEN TIP Calibrating the PENRemoving and Installing the Battery Tips for Conserving Battery Power90% 100%Operation of the Bridge Battery Installing Memory Stick/SD CardsModem Connection Memory STICK/SD Card SlotRemoving and Installing Memory Modules PC Card SlotInstalling a Dimm Module Removing a Memory ModulePage Care and Maintenance Page Care and Maintenance Caring for Your Tablet PCProtecting the Display Screen Cleaning the Display Screen TroubleshootingStoring the Tablet PC Avoiding OverheatingRestoring Your PRE-INSTALLED Software Boot Priority Change ProcedureRestoring the Factory Image Specifications Page Stylistic ST5000 Series Hardware Specifications Stylistic ST5000 SpecificationsDisplay Specifications Physical SpecificationsPower Specifications Agency Approval SpecificationsAdditional Specifications Agency Notices Page Regulatory Information FCC NoticesAvis Aux Utilisateurs Du Réseau Téléphonique Canadien UL Notice AC Adapter output polarityFor Authorized Repair Technicians Only System DisposalPage Appendix a Page FCC Regulatory Information Before Using the Wireless LAN Types of Wireless LANs Covered by this DocumentCharacteristics of the Wireless Module Wireless LAN Modes Using this Wireless ModuleAccess Point Infrastructure Mode See Figure A-2 How to Handle This Wireless ModuleFor Better Communications Deactivation using the wireless switch Deactivation using WindowsStopping Transmission Starting TransmissionConnecting the Wlan Preparation for Wireless LAN ConnectionFlow of Operations Assigning parametersClose the Wireless Network window Setting the network Setting TCP/IPSetting the sharing function Connection to the NetworkSetting the Microsoft network-sharing service Setting the file-sharing functionSetting the printer-sharing function Confirming connection Confirming the status of the radioTransmit Power Level Power Save ModeIP Address CountryOther settings Setting of POWER-SAVING FunctionSetting of transmission power during ad hoc connection Setting of channels during ad hoc connectionTroubleshooting UnavailableNetwork ConnectionAccess point CommunicationIs disconnected Soon afterWireless LAN Glossary Open system authentication Shared key authenticationSsid Service Set Identifier Wi-FiIP address information Specifications SpecificationUsing the Bluetooth Device What is BLUETOOTH?Where to Find Information About Bluetooth WarrantyAppendix B Page Installing Omnipass Installing the OmniPass ApplicationIntroducing the Optional Fingerprint Sensor Device Getting StartedUninstalling OmniPass Master Password ConceptUser Enrollment Verifying Information about OmniPassUsing Omnipass Password ReplacementOmniPass Authentication Toolbar Remembering a PasswordPassword Management Logging in to a Remembered SiteConfiguring Omnipass Identities and Password ManagementOmniPass User Identities Exporting and Importing UsersOmnipass Control Center Exporting an OmniPass User ProfileImporting an OmniPass User Profile Things to Know Regarding Import/ExportUser Settings System SettingsFirst option, Automatically log on to OmniPass as Cannot add a User with a Blank Password to OmniPass Cannot add Windows users to OmniPassTrusted Platform Module Installation Installing the TPM ApplicationsProcedure Enabling the Security Chip in BiosPage Adjusting the display brightness Air flow vents IndexMicrophone Microphone jack Storing the system unit Stylistic ST5000 Y l i s t i c S T 5 0 0 0 S e r i e s T a b l e t P C