Zebra Technologies 170PAX2TM manual Setting the Label Top Position

Page 30

Configuration and Calibration

Setting the Label Top Position

The Label Top Position controls the initial vertical print position on the label (viewed as the label exits the printer). The Default position is referenced to the leading edge of the label which follows the one to be printed. Refer to Figure 11. If there is a lengthy web between labels, the label format may begin printing on the backing material. To set the position where the format begins printing, change the Label Top Position value.

LABEL TOP +000

-nnnnnnn +

Press the right oval key to increase the value , or press the left oval key to decrease the value. Each positive number moves the label top position down by one dot row; each negative number moves the position up by one dot row.

Default: +0

Range: -120 to +120

Press the NEXT key to display LEFT POSITION.

LABEL TOP

POSITION

LABEL

LENGTH

LABEL

FEED

LABEL TOP				LABEL
POSITION				LABEL
+80 DOT ROWS				LENGTH

	Figure 11. Label Top Position
26	170PAX2-Series User’s Guide

Image 30

Contents

Zebra 170PAX2 -Series User ’s Guide FCC Compliance Statement Proprietary StatementProduct Improvements Canadian DOC Compliance StatementContents Options 170PAX2-Series User’s GuideGetting Started IntroductionZebra 170PAX2 Print Engine Print Engine MountingPrinter Power Cable ConnectionsMedia & Ribbon Loading Media LoadingMedia Loading Left-Hand Units Ribbon Loading Right Hand UnitsRemoving Used Ribbon Left Hand UnitsMedia Sensor Position Reflective Media SensorTransmissive Media Sensor 170PAX2-Series User’s Guide Power On/Off Switch Printer OperationFront Panel Keys Front Panel Indicator Lights LEDs Liquid Crystal DisplayControl Panel Keys Changing Password-Protected Parameters Configuration and CalibrationEntering the Program Mode Leaving the Program ModeConfiguration Process Setting Print ParametersSetting Darkness Selecting the Media Type Setting the Tear Off PositionSelecting the Print Mode Selecting the Sensor TypeSetting the Print Width Setting the Maximum Label LengthSelecting the Print Method Label Feed Listing Printer Information Initialize Card Media and Ribbon Sensor Calibration Sensor ProfileMedia and Ribbon Calibration Setting the Baud Rate Setting Communication ParametersSetting the Host Port Setting the Data BitsSetting the Host Handshake Setting the ParitySetting the Stop Bits Setting the Protocol Setting the Network ID Setting the Communications ModeFormat Prefix Character Selecting Prefix and Delimiter CharactersControl Prefix Character Delimiter CharacterPower Up and Head Close Parameters Selecting ZPL ModeSetting Ribbon Tension Media Power UpLabel Positioning Parameters Head CloseBackfeed Sequence Setting the Label Top Position Label Top PositionSetting the Left Position Left Position 170 PAX2-Series User’s GuideHead Test Function Head ResistanceVerifier Port Setting the Applicator Port Applicator PortSetting the Start Print Signal Setting the Resync ModePrinting Controls Selecting the Ribbon Low Feature Reprint ModeSensor Values LCD Adjust Printer LanguageSelecting the Liquid Crystal Display LCD Language Cleaning the Exterior Care & AdjustmentsCleaning Cleaning the InteriorCleaning the Printhead and Platen Roller Sensor Locations Right-Hand Unit ShownPrinthead Pressure Adjustment Toggle PositioningPrinthead Pressure Right-Hand Unit Shown Troubleshooting Power On Self TestFor Thermal Transfer Power On TroubleshootingPrinter Troubleshooting For Direct ThermalBuilding Format Explanation of Errors Creating BitmapStoring Bitmap Storing FormatFirst calibrate the printer, then CC , CT , and CD Cancel Key Self Test Printer Self TestsIntroduction Pause Key Self Test Pause Key Test Sample Printout 170PAX2-Series User’s GuideFeed Key Self Test Feed Key Self TestFeed Key and Pause Key Parameter Controlled byCommunications Diagnostics Test Results of Communications Diagnostic TestCommunication Interfaces OptionsSingle In-line Memory Module Simm ZebraNet Micro Print Server MPS170PAX2-Series User’s Guide Ribbon Specifications Printer SpecificationsMedia Specifications Printing ConsiderationsCommunications Specifications Zebra Programming Language ZPLBar Codes Standard Printer Fonts Electrical MemoryPhysical FusesAC Power Cord Specifications AC Power Cord RequirementsPower Fuse Replacement Appendix aInstalling a Fuse ShippingSystem Considerations Appendix BPrinter Communications Interface Technical Information Interface ConsiderationsRS-232/RS-422/RS-485 Serial Data Port RS-232/RS-422/RS-485 PinoutsPin to 25-Pin Interconnecting Cable RS-422/RS-485 Interconnecting Cable Centronics-Compatible Parallel Data Port Applicator Interface Connector DB-15 Connector Printer to ApplicatorCabling Requirements See the Configuration and Calibration section Fuse 1 JP1 JP2 Ascii Code Chart Appendix C170PAX2-Series User’s Guide Adjusting Darkness For In-Spec Bar Codes Appendix DIn-Spec Bar Code Darkness ComparisonInstallation Information Appendix EFront View of Right Hand Printer 451 748 11.45 mm 222.2 mm 170PAX2-Series User’s Guide Glossary Glossary Printer configuration See configuration 170PAX2-Series User’s Guide Index Index Index Page Page Zebra Technologies Corporation