Zebra Technologies 170PAX2TM manual Cabling Requirements, Applicator Interface Connector

Page 64

Appendix B

Cabling Requirements

Data cables must be fully shielded and fitted with metal or metalized connector shells. Shielded cables and connectors are required to prevent radiation and reception of electrical noise. To minimize electrical noise pickup in the cable:

•Keep data cables as short as possible.

•Do not bundle the data cables tightly with the power cords.

•Do not tie the data cables to power wire conduits.

NOTE: Printers comply with FCC “Rules and Regulations,” Part 15, Subpart “J,” for Class “A” equipment, using fully-shielded 6-foot data cables. Use of longer cables or unshielded cables may increase radiated emissions above the Class “A” limits.

NOTE: RS-422 and RS-485 applications should use shielded twisted pairs with 120 ohm controlled impedance as recommended in the Appendix of the ITA/EIA-485 specification.

Applicator Interface Connector

Refer to Table 4. An external DB-15 connector is present on the rear panel of the print engine for communication with the applicator. (An optional DB-15 to DB-9 adapter cable is available to accommodate existing DB-9 interfaces.)

PIN

SIGNAL

SIGNAL

 

#

NAME

TYPE

FUNCTIONAL DESCRIPTION

 

 

 

 

1

SIGNAL

Ground

JP1 IN – Ground return for Internal +5v power source and is

 

GROUND

 

available here for remote opto-isolators, if required. (JP2 IN)

 

 

 

 

(+5V Re-

 

JP1 OUT – Ground return for External +5v power source. (JP2 OUT)

 

turn)

 

 

 

 

2

+5V

Power

JP2 IN – Internal +5v power source supplies power to internal

 

(Fused at

 

opto-isolators and is available here for remote opto-isolators,

 

 

if required. (JP1 IN)

 

750mA)

 

 

 

 

 

 

 

JP2 OUT – External +5v power source must be connected

 

 

 

here to supply power to internal opto-isolators. (JP1 OUT)

3

 

Input

PULSE MODE – The label printing process begins on the

 

START

 

HIGH to LOW transition of this signal, if a format is ready.

 

 

De-assert this signal HIGH to inhibit printing of a new label.

 

PRINT

 

 

 

 

 

 

 

LEVEL MODE – Assert LOW to enable the printer to begin

 

 

 

printing, if a format is ready. The printer will print new labels

 

 

 

as long as the signal is asserted. When de-asserted, the

 

 

 

currently printing label will be completed and the printer will

 

 

 

stop and wait for this input to be reasserted LOW.

4

FEED

Input

When the printer is in an Idle state or has been PAUSED,

 

 

 

assert this input LOW to trigger repeated feeding of blank

 

 

 

labels. De-assert HIGH to stop feeding blank labels and

 

 

 

register to the top of the next label.

Table 4. DB-15 Connector (Printer to Applicator)

60

170PAX2-Series User’s Guide

Page 63 Page 65
Image 64
Page 63 Page 65
Contents Zebra 170PAX2 -Series User ’s Guide Proprietary Statement Product ImprovementsFCC Compliance Statement Canadian DOC Compliance StatementContents Options 170PAX2-Series User’s GuideIntroduction Zebra 170PAX2 Print EngineGetting Started Print Engine MountingPrinter Power Cable ConnectionsMedia & Ribbon Loading Media LoadingMedia Loading Left-Hand Units Ribbon Loading Right Hand UnitsRemoving Used Ribbon Left Hand UnitsReflective Media Sensor Media Sensor PositionTransmissive Media Sensor 170PAX2-Series User’s Guide Printer Operation Power On/Off SwitchFront Panel Keys Liquid Crystal Display Front Panel Indicator Lights LEDsControl Panel Keys Configuration and Calibration Entering the Program ModeChanging Password-Protected Parameters Leaving the Program ModeSetting Print Parameters Configuration ProcessSetting Darkness Setting the Tear Off Position Selecting the Print ModeSelecting the Media Type Selecting the Sensor TypeSetting the Maximum Label Length Setting the Print WidthSelecting the Print Method Label Feed Listing Printer Information Initialize Card Media and Ribbon Sensor Calibration Sensor ProfileMedia and Ribbon Calibration Setting Communication Parameters Setting the Host PortSetting the Baud Rate Setting the Data BitsSetting the Parity Setting the Stop BitsSetting the Host Handshake Setting the ProtocolSetting the Network ID Setting the Communications ModeSelecting Prefix and Delimiter Characters Control Prefix CharacterFormat Prefix Character Delimiter CharacterSelecting ZPL Mode Setting Ribbon TensionPower Up and Head Close Parameters Media Power UpHead Close Label Positioning ParametersBackfeed Sequence Setting the Label Top Position Label Top PositionSetting the Left Position Left Position 170 PAX2-Series User’s GuideHead Resistance Head Test FunctionVerifier Port Setting the Applicator Port Applicator PortSetting the Resync Mode Setting the Start Print SignalPrinting Controls Reprint Mode Selecting the Ribbon Low FeatureSensor Values Printer Language LCD AdjustSelecting the Liquid Crystal Display LCD Language Care & Adjustments CleaningCleaning the Exterior Cleaning the InteriorCleaning the Printhead and Platen Roller Sensor Locations Right-Hand Unit ShownPrinthead Pressure Adjustment Toggle PositioningPrinthead Pressure Right-Hand Unit Shown Troubleshooting Power On Self TestPower On Troubleshooting Printer TroubleshootingFor Thermal Transfer For Direct ThermalExplanation of Errors Creating Bitmap Storing BitmapBuilding Format Storing FormatFirst calibrate the printer, then CC , CT , and CD Printer Self Tests Cancel Key Self TestIntroduction Pause Key Self Test Pause Key Test Sample Printout 170PAX2-Series User’s GuideFeed Key Self Test Feed Key Self TestFeed Key and Pause Key Parameter Controlled byCommunications Diagnostics Test Results of Communications Diagnostic TestOptions Single In-line Memory Module SimmCommunication Interfaces ZebraNet Micro Print Server MPS170PAX2-Series User’s Guide Printer Specifications Media SpecificationsRibbon Specifications Printing ConsiderationsZebra Programming Language ZPL Communications SpecificationsBar Codes Standard Printer Fonts Memory PhysicalElectrical FusesAC Power Cord Requirements Power Fuse ReplacementAC Power Cord Specifications Appendix aInstalling a Fuse ShippingAppendix B Printer Communications Interface Technical InformationSystem Considerations Interface ConsiderationsRS-232/RS-422/RS-485 Serial Data Port RS-232/RS-422/RS-485 PinoutsPin to 25-Pin Interconnecting Cable RS-422/RS-485 Interconnecting Cable Centronics-Compatible Parallel Data Port DB-15 Connector Printer to Applicator Applicator Interface ConnectorCabling Requirements See the Configuration and Calibration section Fuse 1 JP1 JP2 Ascii Code Chart Appendix C170PAX2-Series User’s Guide Adjusting Darkness For In-Spec Bar Codes Appendix DIn-Spec Bar Code Darkness ComparisonInstallation Information Appendix EFront View of Right Hand Printer 451 748 11.45 mm 222.2 mm 170PAX2-Series User’s Guide Glossary Glossary Printer configuration See configuration 170PAX2-Series User’s Guide Index Index Index Page Page Zebra Technologies Corporation

170PAX2TM specifications

Zebra Technologies, a leader in industrial printing solutions, offers the 170PAX2TM printer, a versatile and robust solution targeted towards high-performance applications. Designed for industrial environments, the 170PAX2TM stands out for its advanced features and technologies that elevate operational efficiency and streamline workflows.

One of the key features of the 170PAX2TM is its exceptional printing speed. Capable of producing high-quality labels at a rapid pace, this printer significantly reduces the time required for label production, making it an ideal choice for businesses with large-scale printing needs. The printer supports a broad range of media types and sizes, allowing users to create everything from small labels to larger tags with ease.

Another hallmark of the 170PAX2TM is its rugged design. Built to endure the demanding conditions of industrial settings, this printer features a durable housing that can withstand impacts, dust, and moisture. This durability ensures long-term performance and reliability, reducing maintenance costs and downtime.

In addition to its robust build, the 170PAX2TM incorporates state-of-the-art printing technologies. It utilizes direct thermal and thermal transfer printing methods, providing flexibility for various label materials. The printer's advanced thermal printhead technology ensures sharp, clear images and text, which is essential for barcode clarity and scannability.

The 170PAX2TM also boasts user-friendly features, including a large LCD display that simplifies navigation and operation. With intuitive controls, users can easily adjust settings, monitor print jobs, and perform maintenance tasks with minimal training. The printer also supports various connectivity options, including USB, Serial, and Ethernet, making integration into existing systems straightforward.

The device is also designed with energy efficiency in mind. It features power-saving modes that help reduce energy consumption, contributing to a greener, more sustainable workplace. Additionally, its smaller footprint allows it to fit seamlessly into any production line without taking up excessive space.

Overall, Zebra Technologies' 170PAX2TM printer combines speed, durability, and advanced printing capabilities, making it an invaluable asset for businesses looking to enhance their labeling processes. Whether in warehousing, manufacturing, or distribution, the 170PAX2TM delivers dependable performance that meets the high demands of today's industrial environments.
Top Page Image Contents