Zebra Technologies 170PAX2TM manual Printer Self Tests, Introduction, Cancel Key Self Test

Page 46

Troubleshooting

Printer Self Tests

Introduction

These self tests, illustrated on the following pages, produce sample labels and provide specific information that help determine the operating conditions for the printer.

Each self test is enabled by pressing a specific control panel key or combination of keys while turning the power switch ON. Keep the key pressed until the first indicator light turns OFF. The selected self test will automatically start at the end of the Power On Self Test.

NOTE: When performing these self tests, do not send data to the printer from the Host.

NOTE: Full width media should be used when performing Printer Self Tests. If your media is not wide enough, the test labels may print on the label and the platen roller, or in the case of narrow media, not on the label at all. To prevent this from happening, check the configuration parameter “Setting the Print Width”, and insure it is correct for the media you are using.

NOTE: If your media is too short, the test label will continue on the next label.

NOTE: When canceling a self test prior to its actual completion, always reset the printer by turning the printer power OFF and then ON.

NOTE: When performing these self tests, the operator must manually remove the labels as they become available.

CANCEL Key Self Test

Press and hold the CANCEL key while turning the printer power ON. Release the key anytime after the first front panel LED turns OFF.

This self test prints a label that contains a listing of the printer’s current configuration parameters stored in configuration (EEPROM) memory (refer to Figure 16). To enable this test, press the CANCEL key while turning on the power switch.

The configuration may be changed either temporarily (for specific label formats or ribbon and label stock) or permanently (by saving the new parameters in EEPROM memory). Saving new parameters occurs whenever a printer calibration procedure is performed. Refer to “Configuration and Calibration” for further details.

 

Figure 16. CANCEL Key Self Test

42

170PAX2-Series User’s Guide

Page 45 Page 47
Image 46
Page 45 Page 47
Contents Zebra 170PAX2 -Series User ’s Guide FCC Compliance Statement Proprietary StatementProduct Improvements Canadian DOC Compliance StatementContents Options 170PAX2-Series User’s GuideGetting Started IntroductionZebra 170PAX2 Print Engine Print Engine MountingPrinter Power Cable ConnectionsMedia & Ribbon Loading Media LoadingMedia Loading Left-Hand Units Ribbon Loading Right Hand UnitsRemoving Used Ribbon Left Hand UnitsReflective Media Sensor Media Sensor PositionTransmissive Media Sensor 170PAX2-Series User’s Guide Printer Operation Power On/Off SwitchFront Panel Keys Liquid Crystal Display Front Panel Indicator Lights LEDsControl Panel Keys Changing Password-Protected Parameters Configuration and CalibrationEntering the Program Mode Leaving the Program ModeSetting Print Parameters Configuration ProcessSetting Darkness Selecting the Media Type Setting the Tear Off PositionSelecting the Print Mode Selecting the Sensor TypeSetting the Maximum Label Length Setting the Print WidthSelecting the Print Method Label Feed Listing Printer Information Initialize Card Media and Ribbon Sensor Calibration Sensor ProfileMedia and Ribbon Calibration Setting the Baud Rate Setting Communication ParametersSetting the Host Port Setting the Data BitsSetting the Host Handshake Setting the ParitySetting the Stop Bits Setting the ProtocolSetting the Network ID Setting the Communications ModeFormat Prefix Character Selecting Prefix and Delimiter CharactersControl Prefix Character Delimiter CharacterPower Up and Head Close Parameters Selecting ZPL ModeSetting Ribbon Tension Media Power UpHead Close Label Positioning ParametersBackfeed Sequence Setting the Label Top Position Label Top PositionSetting the Left Position Left Position 170 PAX2-Series User’s GuideHead Resistance Head Test FunctionVerifier Port Setting the Applicator Port Applicator PortSetting the Resync Mode Setting the Start Print SignalPrinting Controls Reprint Mode Selecting the Ribbon Low FeatureSensor Values Printer Language LCD AdjustSelecting the Liquid Crystal Display LCD Language Cleaning the Exterior Care & AdjustmentsCleaning Cleaning the InteriorCleaning the Printhead and Platen Roller Sensor Locations Right-Hand Unit ShownPrinthead Pressure Adjustment Toggle PositioningPrinthead Pressure Right-Hand Unit Shown Troubleshooting Power On Self TestFor Thermal Transfer Power On TroubleshootingPrinter Troubleshooting For Direct ThermalBuilding Format Explanation of Errors Creating BitmapStoring Bitmap Storing FormatFirst calibrate the printer, then CC , CT , and CD Printer Self Tests Cancel Key Self TestIntroduction Pause Key Self Test Pause Key Test Sample Printout 170PAX2-Series User’s GuideFeed Key Self Test Feed Key Self TestFeed Key and Pause Key Parameter Controlled byCommunications Diagnostics Test Results of Communications Diagnostic TestCommunication Interfaces OptionsSingle In-line Memory Module Simm ZebraNet Micro Print Server MPS170PAX2-Series User’s Guide Ribbon Specifications Printer SpecificationsMedia Specifications Printing ConsiderationsZebra Programming Language ZPL Communications SpecificationsBar Codes Standard Printer Fonts Electrical MemoryPhysical FusesAC Power Cord Specifications AC Power Cord RequirementsPower Fuse Replacement Appendix aInstalling a Fuse ShippingSystem Considerations Appendix BPrinter Communications Interface Technical Information Interface ConsiderationsRS-232/RS-422/RS-485 Serial Data Port RS-232/RS-422/RS-485 PinoutsPin to 25-Pin Interconnecting Cable RS-422/RS-485 Interconnecting Cable Centronics-Compatible Parallel Data Port DB-15 Connector Printer to Applicator Applicator Interface ConnectorCabling Requirements See the Configuration and Calibration section Fuse 1 JP1 JP2 Ascii Code Chart Appendix C170PAX2-Series User’s Guide Adjusting Darkness For In-Spec Bar Codes Appendix DIn-Spec Bar Code Darkness ComparisonInstallation Information Appendix EFront View of Right Hand Printer 451 748 11.45 mm 222.2 mm 170PAX2-Series User’s Guide Glossary Glossary Printer configuration See configuration 170PAX2-Series User’s Guide Index Index Index Page Page Zebra Technologies Corporation

170PAX2TM specifications

Zebra Technologies, a leader in industrial printing solutions, offers the 170PAX2TM printer, a versatile and robust solution targeted towards high-performance applications. Designed for industrial environments, the 170PAX2TM stands out for its advanced features and technologies that elevate operational efficiency and streamline workflows.

One of the key features of the 170PAX2TM is its exceptional printing speed. Capable of producing high-quality labels at a rapid pace, this printer significantly reduces the time required for label production, making it an ideal choice for businesses with large-scale printing needs. The printer supports a broad range of media types and sizes, allowing users to create everything from small labels to larger tags with ease.

Another hallmark of the 170PAX2TM is its rugged design. Built to endure the demanding conditions of industrial settings, this printer features a durable housing that can withstand impacts, dust, and moisture. This durability ensures long-term performance and reliability, reducing maintenance costs and downtime.

In addition to its robust build, the 170PAX2TM incorporates state-of-the-art printing technologies. It utilizes direct thermal and thermal transfer printing methods, providing flexibility for various label materials. The printer's advanced thermal printhead technology ensures sharp, clear images and text, which is essential for barcode clarity and scannability.

The 170PAX2TM also boasts user-friendly features, including a large LCD display that simplifies navigation and operation. With intuitive controls, users can easily adjust settings, monitor print jobs, and perform maintenance tasks with minimal training. The printer also supports various connectivity options, including USB, Serial, and Ethernet, making integration into existing systems straightforward.

The device is also designed with energy efficiency in mind. It features power-saving modes that help reduce energy consumption, contributing to a greener, more sustainable workplace. Additionally, its smaller footprint allows it to fit seamlessly into any production line without taking up excessive space.

Overall, Zebra Technologies' 170PAX2TM printer combines speed, durability, and advanced printing capabilities, making it an invaluable asset for businesses looking to enhance their labeling processes. Whether in warehousing, manufacturing, or distribution, the 170PAX2TM delivers dependable performance that meets the high demands of today's industrial environments.
Top Page Image Contents