Zebra Technologies 170PAX2TM manual Setting the Left Position

Page 31

Configuration and Calibration

Setting the Left Position

The Left Position controls the initial print position from the left edge of a label (viewed as the label exits the printer). The Default position is referenced to the left edge of the media. Refer to Figure 12. Depending on the width of the media, the label format may begin printing on the backing material or on the platen. To set the position where the format begins printing, change the Left Position value.

LEFT POSITION

 

®

+ 0000

+

Press the left oval key to move the cursor to the next digit, and press the right oval key to change the +/- value and increase the value of the digit (“+” shifts to the left; “-” shifts to the right.) The displayed value represents the number of dot positions the format will shift right or left.

Default: 0000

Range: -9999 to +9999 (If a negative value is required, enter the numeric value first, then change the plus to a minus sign.)

Press the NEXT key to display HEAD TEST COUNT.

LABEL

FEED

LEFT

POSITION

LEFT

POSITION

-35 DOT ROWS

LABEL

LENGTH

Figure 12. Left Position

 

170PAX2-Series User’s Guide

27

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Zebra 170PAX2 -Series User ’s Guide Canadian DOC Compliance Statement Proprietary StatementProduct Improvements FCC Compliance StatementContents 170PAX2-Series User’s Guide OptionsPrint Engine Mounting IntroductionZebra 170PAX2 Print Engine Getting StartedCable Connections Printer PowerMedia Loading Media & Ribbon LoadingMedia Loading Left-Hand Units Right Hand Units Ribbon LoadingLeft Hand Units Removing Used RibbonReflective Media Sensor Media Sensor PositionTransmissive Media Sensor 170PAX2-Series User’s Guide Printer Operation Power On/Off SwitchFront Panel Keys Liquid Crystal Display Front Panel Indicator Lights LEDsControl Panel Keys Leaving the Program Mode Configuration and CalibrationEntering the Program Mode Changing Password-Protected ParametersSetting Print Parameters Configuration ProcessSetting Darkness Selecting the Sensor Type Setting the Tear Off PositionSelecting the Print Mode Selecting the Media TypeSetting the Maximum Label Length Setting the Print WidthSelecting the Print Method Label Feed Listing Printer Information Initialize Card Sensor Profile Media and Ribbon Sensor CalibrationMedia and Ribbon Calibration Setting the Data Bits Setting Communication ParametersSetting the Host Port Setting the Baud RateSetting the Protocol Setting the ParitySetting the Stop Bits Setting the Host HandshakeSetting the Communications Mode Setting the Network IDDelimiter Character Selecting Prefix and Delimiter CharactersControl Prefix Character Format Prefix CharacterMedia Power Up Selecting ZPL ModeSetting Ribbon Tension Power Up and Head Close ParametersHead Close Label Positioning ParametersBackfeed Sequence Label Top Position Setting the Label Top PositionLeft Position 170 PAX2-Series User’s Guide Setting the Left PositionHead Resistance Head Test FunctionVerifier Port Applicator Port Setting the Applicator PortSetting the Resync Mode Setting the Start Print SignalPrinting Controls Reprint Mode Selecting the Ribbon Low FeatureSensor Values Printer Language LCD AdjustSelecting the Liquid Crystal Display LCD Language Cleaning the Interior Care & AdjustmentsCleaning Cleaning the ExteriorSensor Locations Right-Hand Unit Shown Cleaning the Printhead and Platen RollerToggle Positioning Printhead Pressure AdjustmentPrinthead Pressure Right-Hand Unit Shown Power On Self Test TroubleshootingFor Direct Thermal Power On TroubleshootingPrinter Troubleshooting For Thermal TransferStoring Format Explanation of Errors Creating BitmapStoring Bitmap Building FormatFirst calibrate the printer, then CC , CT , and CD Printer Self Tests Cancel Key Self TestIntroduction Pause Key Test Sample Printout 170PAX2-Series User’s Guide Pause Key Self TestFeed Key Self Test Feed Key Self TestParameter Controlled by Feed Key and Pause KeyResults of Communications Diagnostic Test Communications Diagnostics TestZebraNet Micro Print Server MPS OptionsSingle In-line Memory Module Simm Communication Interfaces170PAX2-Series User’s Guide Printing Considerations Printer SpecificationsMedia Specifications Ribbon SpecificationsZebra Programming Language ZPL Communications SpecificationsBar Codes Standard Printer Fonts Fuses MemoryPhysical ElectricalAppendix a AC Power Cord RequirementsPower Fuse Replacement AC Power Cord SpecificationsShipping Installing a FuseInterface Considerations Appendix BPrinter Communications Interface Technical Information System ConsiderationsRS-232/RS-422/RS-485 Pinouts RS-232/RS-422/RS-485 Serial Data PortPin to 25-Pin Interconnecting Cable RS-422/RS-485 Interconnecting Cable Centronics-Compatible Parallel Data Port DB-15 Connector Printer to Applicator Applicator Interface ConnectorCabling Requirements See the Configuration and Calibration section Fuse 1 JP1 JP2 Appendix C Ascii Code Chart170PAX2-Series User’s Guide Appendix D Adjusting Darkness For In-Spec Bar CodesBar Code Darkness Comparison In-SpecAppendix E Installation InformationFront View of Right Hand Printer 451 748 11.45 mm 222.2 mm 170PAX2-Series User’s Guide Glossary Glossary Printer configuration See configuration 170PAX2-Series User’s Guide Index Index Index Page Page Zebra Technologies Corporation

170PAX2TM specifications

Zebra Technologies, a leader in industrial printing solutions, offers the 170PAX2TM printer, a versatile and robust solution targeted towards high-performance applications. Designed for industrial environments, the 170PAX2TM stands out for its advanced features and technologies that elevate operational efficiency and streamline workflows.

One of the key features of the 170PAX2TM is its exceptional printing speed. Capable of producing high-quality labels at a rapid pace, this printer significantly reduces the time required for label production, making it an ideal choice for businesses with large-scale printing needs. The printer supports a broad range of media types and sizes, allowing users to create everything from small labels to larger tags with ease.

Another hallmark of the 170PAX2TM is its rugged design. Built to endure the demanding conditions of industrial settings, this printer features a durable housing that can withstand impacts, dust, and moisture. This durability ensures long-term performance and reliability, reducing maintenance costs and downtime.

In addition to its robust build, the 170PAX2TM incorporates state-of-the-art printing technologies. It utilizes direct thermal and thermal transfer printing methods, providing flexibility for various label materials. The printer's advanced thermal printhead technology ensures sharp, clear images and text, which is essential for barcode clarity and scannability.

The 170PAX2TM also boasts user-friendly features, including a large LCD display that simplifies navigation and operation. With intuitive controls, users can easily adjust settings, monitor print jobs, and perform maintenance tasks with minimal training. The printer also supports various connectivity options, including USB, Serial, and Ethernet, making integration into existing systems straightforward.

The device is also designed with energy efficiency in mind. It features power-saving modes that help reduce energy consumption, contributing to a greener, more sustainable workplace. Additionally, its smaller footprint allows it to fit seamlessly into any production line without taking up excessive space.

Overall, Zebra Technologies' 170PAX2TM printer combines speed, durability, and advanced printing capabilities, making it an invaluable asset for businesses looking to enhance their labeling processes. Whether in warehousing, manufacturing, or distribution, the 170PAX2TM delivers dependable performance that meets the high demands of today's industrial environments.
Top Page Image Contents