Zebra Technologies 170PAX2TM manual Appendix a, AC Power Cord Requirements, Power Fuse Replacement

Page 57

Appendix A

AC Power Cord Requirements

Since many areas of the world have specific power requirements, an AC Power Cord may not be included with your printer. Refer to Figure 20. A power cord must be provided by you that meets your local electrical requirements.

WARNING!! For personnel and equipment safety, always use a three-prong plug with an earth ground connection to the AC Power Source.

AC Power Cord Specifications:

•The overall length must be less than 9.8 feet (3 m).

•It must be rated for at least 5 Amp, 250 VAC.

•The chassis ground (earth) must be connected to assure safety and reduce electro- magnetic interference. This is done by the third wire (earth) in the power cord.

•The AC power plug and IEC320 connector should bear the certification mark of at least one of the known international safety organization shown in Figure 20.

Figure 20. VAC Power Cord

Figure 21. Safety Organization Logos

Power Fuse Replacement

The printer uses a metric-style fuse (5 x 20 mm IEC) rated for 5 Amps at 250 Volts that bears the certification mark of a known international safety organization (see Figure 21).

The power entry module comes with two approved fuses in the fuse holder; one is “in-circuit” and one is provided as a “spare.”

170PAX2-Series User’s Guide

53

Page 56 Page 58
Image 57
Page 56 Page 58
Contents Zebra 170PAX2 -Series User ’s Guide Product Improvements Proprietary StatementFCC Compliance Statement Canadian DOC Compliance StatementContents 170PAX2-Series User’s Guide OptionsZebra 170PAX2 Print Engine IntroductionGetting Started Print Engine MountingCable Connections Printer PowerMedia Loading Media & Ribbon LoadingMedia Loading Left-Hand Units Right Hand Units Ribbon LoadingLeft Hand Units Removing Used RibbonMedia Sensor Position Reflective Media SensorTransmissive Media Sensor 170PAX2-Series User’s Guide Power On/Off Switch Printer OperationFront Panel Keys Front Panel Indicator Lights LEDs Liquid Crystal DisplayControl Panel Keys Entering the Program Mode Configuration and CalibrationChanging Password-Protected Parameters Leaving the Program ModeConfiguration Process Setting Print ParametersSetting Darkness Selecting the Print Mode Setting the Tear Off PositionSelecting the Media Type Selecting the Sensor TypeSetting the Print Width Setting the Maximum Label LengthSelecting the Print Method Label Feed Listing Printer Information Initialize Card Sensor Profile Media and Ribbon Sensor CalibrationMedia and Ribbon Calibration Setting the Host Port Setting Communication ParametersSetting the Baud Rate Setting the Data BitsSetting the Stop Bits Setting the ParitySetting the Host Handshake Setting the ProtocolSetting the Communications Mode Setting the Network IDControl Prefix Character Selecting Prefix and Delimiter CharactersFormat Prefix Character Delimiter CharacterSetting Ribbon Tension Selecting ZPL ModePower Up and Head Close Parameters Media Power UpLabel Positioning Parameters Head CloseBackfeed Sequence Label Top Position Setting the Label Top PositionLeft Position 170 PAX2-Series User’s Guide Setting the Left PositionHead Test Function Head ResistanceVerifier Port Applicator Port Setting the Applicator PortSetting the Start Print Signal Setting the Resync ModePrinting Controls Selecting the Ribbon Low Feature Reprint ModeSensor Values LCD Adjust Printer LanguageSelecting the Liquid Crystal Display LCD Language Cleaning Care & AdjustmentsCleaning the Exterior Cleaning the InteriorSensor Locations Right-Hand Unit Shown Cleaning the Printhead and Platen RollerToggle Positioning Printhead Pressure AdjustmentPrinthead Pressure Right-Hand Unit Shown Power On Self Test TroubleshootingPrinter Troubleshooting Power On TroubleshootingFor Thermal Transfer For Direct ThermalStoring Bitmap Explanation of Errors Creating BitmapBuilding Format Storing FormatFirst calibrate the printer, then CC , CT , and CD Cancel Key Self Test Printer Self TestsIntroduction Pause Key Test Sample Printout 170PAX2-Series User’s Guide Pause Key Self TestFeed Key Self Test Feed Key Self TestParameter Controlled by Feed Key and Pause KeyResults of Communications Diagnostic Test Communications Diagnostics TestSingle In-line Memory Module Simm OptionsCommunication Interfaces ZebraNet Micro Print Server MPS170PAX2-Series User’s Guide Media Specifications Printer SpecificationsRibbon Specifications Printing ConsiderationsCommunications Specifications Zebra Programming Language ZPLBar Codes Standard Printer Fonts Physical MemoryElectrical FusesPower Fuse Replacement AC Power Cord RequirementsAC Power Cord Specifications Appendix aShipping Installing a FusePrinter Communications Interface Technical Information Appendix BSystem Considerations Interface ConsiderationsRS-232/RS-422/RS-485 Pinouts RS-232/RS-422/RS-485 Serial Data PortPin to 25-Pin Interconnecting Cable RS-422/RS-485 Interconnecting Cable Centronics-Compatible Parallel Data Port Applicator Interface Connector DB-15 Connector Printer to ApplicatorCabling Requirements See the Configuration and Calibration section Fuse 1 JP1 JP2 Appendix C Ascii Code Chart170PAX2-Series User’s Guide Appendix D Adjusting Darkness For In-Spec Bar CodesBar Code Darkness Comparison In-SpecAppendix E Installation InformationFront View of Right Hand Printer 451 748 11.45 mm 222.2 mm 170PAX2-Series User’s Guide Glossary Glossary Printer configuration See configuration 170PAX2-Series User’s Guide Index Index Index Page Page Zebra Technologies Corporation

170PAX2TM specifications

Zebra Technologies, a leader in industrial printing solutions, offers the 170PAX2TM printer, a versatile and robust solution targeted towards high-performance applications. Designed for industrial environments, the 170PAX2TM stands out for its advanced features and technologies that elevate operational efficiency and streamline workflows.

One of the key features of the 170PAX2TM is its exceptional printing speed. Capable of producing high-quality labels at a rapid pace, this printer significantly reduces the time required for label production, making it an ideal choice for businesses with large-scale printing needs. The printer supports a broad range of media types and sizes, allowing users to create everything from small labels to larger tags with ease.

Another hallmark of the 170PAX2TM is its rugged design. Built to endure the demanding conditions of industrial settings, this printer features a durable housing that can withstand impacts, dust, and moisture. This durability ensures long-term performance and reliability, reducing maintenance costs and downtime.

In addition to its robust build, the 170PAX2TM incorporates state-of-the-art printing technologies. It utilizes direct thermal and thermal transfer printing methods, providing flexibility for various label materials. The printer's advanced thermal printhead technology ensures sharp, clear images and text, which is essential for barcode clarity and scannability.

The 170PAX2TM also boasts user-friendly features, including a large LCD display that simplifies navigation and operation. With intuitive controls, users can easily adjust settings, monitor print jobs, and perform maintenance tasks with minimal training. The printer also supports various connectivity options, including USB, Serial, and Ethernet, making integration into existing systems straightforward.

The device is also designed with energy efficiency in mind. It features power-saving modes that help reduce energy consumption, contributing to a greener, more sustainable workplace. Additionally, its smaller footprint allows it to fit seamlessly into any production line without taking up excessive space.

Overall, Zebra Technologies' 170PAX2TM printer combines speed, durability, and advanced printing capabilities, making it an invaluable asset for businesses looking to enhance their labeling processes. Whether in warehousing, manufacturing, or distribution, the 170PAX2TM delivers dependable performance that meets the high demands of today's industrial environments.
Top Page Image Contents