Zebra Technologies 170PAX2TM manual Shipping, Installing a Fuse

Page 58

Appendix A

To replace a fuse, follow this procedure and refer to Figure 22:

1.Turn off the printer and unplug the power cord from the back of the printer.

2.Using a small-blade screwdriver, remove the fuse holder from the power entry module at the rear of the printer.

3.Carefully remove the fuse from the “in circuit” location. To remove the fuse from the “spare” location, insert the point of a pencil through one of the two holes in the fuse holder; gently push. Repeat this procedure through the other hole.

4.Insert this fuse in the “in circuit” location. (Remember to replace an approved 250 VAC, 5 Amp fuse in the “spare” location!)

5.Reinstall the fuse holder into the power entry module at the rear of the printer.

6.Reconnect the power cord and turn the printer on.

The printer should now be ready for operation and the POWER light should be on.

NOTE: If power is not restored, an internal component failure may have occurred and the printer requires servicing. Refer to “Troubleshooting.”

Figure 22. Installing a Fuse

Shipping

To ship the Zebra 170PAX2-Series print engine, remove all ribbon and media. Carefully pack the print engine in a suitable container to avoid damage during transit. Whenever possible, use the original “carton within a carton” packing materials from the factory. A shipping container can be purchased from Zebra Technologies Corporation if the original packaging is lost or destroyed. Contact your distributor or Zebra Technologies Corporation to order the 170PAX2-Series Packing Materials Kit.

If you use a different container, package the print engine carefully to avoid damage.

CAUTION: When packaging the printer in a rigid container, use shock mounts or shock-absorbing packing material.

54	170PAX2-Series User’s Guide

Image 58

Contents

Zebra 170PAX2 -Series User ’s Guide FCC Compliance Statement Proprietary StatementProduct Improvements Canadian DOC Compliance StatementContents Options 170PAX2-Series User’s GuideGetting Started IntroductionZebra 170PAX2 Print Engine Print Engine MountingPrinter Power Cable ConnectionsMedia & Ribbon Loading Media LoadingMedia Loading Left-Hand Units Ribbon Loading Right Hand UnitsRemoving Used Ribbon Left Hand UnitsReflective Media Sensor Media Sensor PositionTransmissive Media Sensor 170PAX2-Series User’s Guide Printer Operation Power On/Off SwitchFront Panel Keys Liquid Crystal Display Front Panel Indicator Lights LEDsControl Panel Keys Changing Password-Protected Parameters Configuration and CalibrationEntering the Program Mode Leaving the Program ModeSetting Print Parameters Configuration ProcessSetting Darkness Selecting the Media Type Setting the Tear Off PositionSelecting the Print Mode Selecting the Sensor TypeSetting the Maximum Label Length Setting the Print WidthSelecting the Print Method Label Feed Listing Printer Information Initialize Card Media and Ribbon Sensor Calibration Sensor ProfileMedia and Ribbon Calibration Setting the Baud Rate Setting Communication ParametersSetting the Host Port Setting the Data BitsSetting the Host Handshake Setting the ParitySetting the Stop Bits Setting the ProtocolSetting the Network ID Setting the Communications ModeFormat Prefix Character Selecting Prefix and Delimiter CharactersControl Prefix Character Delimiter CharacterPower Up and Head Close Parameters Selecting ZPL ModeSetting Ribbon Tension Media Power UpHead Close Label Positioning ParametersBackfeed Sequence Setting the Label Top Position Label Top PositionSetting the Left Position Left Position 170 PAX2-Series User’s GuideHead Resistance Head Test FunctionVerifier Port Setting the Applicator Port Applicator PortSetting the Resync Mode Setting the Start Print SignalPrinting Controls Reprint Mode Selecting the Ribbon Low FeatureSensor Values Printer Language LCD AdjustSelecting the Liquid Crystal Display LCD Language Cleaning the Exterior Care & AdjustmentsCleaning Cleaning the InteriorCleaning the Printhead and Platen Roller Sensor Locations Right-Hand Unit ShownPrinthead Pressure Adjustment Toggle PositioningPrinthead Pressure Right-Hand Unit Shown Troubleshooting Power On Self TestFor Thermal Transfer Power On TroubleshootingPrinter Troubleshooting For Direct ThermalBuilding Format Explanation of Errors Creating BitmapStoring Bitmap Storing FormatFirst calibrate the printer, then CC , CT , and CD Printer Self Tests Cancel Key Self TestIntroduction Pause Key Self Test Pause Key Test Sample Printout 170PAX2-Series User’s GuideFeed Key Self Test Feed Key Self TestFeed Key and Pause Key Parameter Controlled byCommunications Diagnostics Test Results of Communications Diagnostic TestCommunication Interfaces OptionsSingle In-line Memory Module Simm ZebraNet Micro Print Server MPS170PAX2-Series User’s Guide Ribbon Specifications Printer SpecificationsMedia Specifications Printing Considerations Zebra Programming Language ZPL Communications Specifications Bar Codes Standard Printer Fonts Electrical MemoryPhysical FusesAC Power Cord Specifications AC Power Cord RequirementsPower Fuse Replacement Appendix aInstalling a Fuse ShippingSystem Considerations Appendix BPrinter Communications Interface Technical Information Interface ConsiderationsRS-232/RS-422/RS-485 Serial Data Port RS-232/RS-422/RS-485 PinoutsPin to 25-Pin Interconnecting Cable RS-422/RS-485 Interconnecting Cable Centronics-Compatible Parallel Data Port DB-15 Connector Printer to Applicator Applicator Interface ConnectorCabling Requirements See the Configuration and Calibration section Fuse 1 JP1 JP2 Ascii Code Chart Appendix C170PAX2-Series User’s Guide Adjusting Darkness For In-Spec Bar Codes Appendix DIn-Spec Bar Code Darkness ComparisonInstallation Information Appendix EFront View of Right Hand Printer 451 748 11.45 mm 222.2 mm 170PAX2-Series User’s Guide Glossary Glossary Printer configuration See configuration 170PAX2-Series User’s Guide Index Index Index Page Page Zebra Technologies Corporation