Rockford Fosgate p3002 manual Specifications, MODEL- Punch P200-2 P300-2 P400-2

Page 10

TROUBLESHOOTING

2.Bypass any and all electrical components between the stereo and the amplifier(s). Connect stereo directly to input of amplifier. If noise goes away the unit being bypassed is the cause of the noise.

OR

3.Remove existing ground wires for all electrical components. Reground wires to different locations. Verify that grounding location is clean, shiny metal free of paint, rust etc.

OR

4.Add secondary ground cable from negative battery terminal to the chassis metal or engine block of vehicle.

OR

5.Have alternator and battery load tested by your mechanic.Verify good working order of vehicle electrical system including distributor, spark plugs, spark plug wires, voltage regulator etc.

SPECIFICATIONS

MODEL- Punch

P200-2

P300-2

P400-2

P500-2

Continuous Power Rating (RMS) - Measured at 14.4 Battery Volts

4

Load Per Channel

50 Watts x 2

2

Load Per Channel

100 Watts x 2

4

Load Bridged

200 Watts x 1

Dimensions:

Height

2.25" (5.71cm)

 

 

Width

7.625" (19.37cm)

 

 

Length

9.0" (22.80cm)

Battery Fuse Rating (Amp)

40A

External (Not Supplied)

 

“A” Weighted Signal to Noise Ratio Referenced to 1 Watt into 4 ohms

“A” Weighted Signal to Noise Ratio Referenced to rated output into 4 ohms

75 Watts x 2

150 Watts x 2

300 Watts x 1

2.25" (5.71cm)

7.625" (19.37cm)

9.0" (22.80cm)

50A

100 Watts x 2

200 Watts x 2

400 Watts x 1

2.25" (5.71cm)

7.625" (19.37cm) 10.25" (26.03cm)

80A

≥85 dB

≥105 dB

125 Watts x 2

250 Watts x 2

500 Watts x 1

2.25" (5.71cm)

7.625" (19.37cm) 13.02" (33.07cm)

100A

Crossover Slope

Crossover Frequency

Frequency Response

Signal Voltage Adjustment Range

Protection

Equalization PEQ (Punch Equalization)

Input Impedance

Operating Voltage

Balanced Inputs

CMRR (Common Mode Rejection Ratio)

Damping Factor

THD+N (Total Harmonic Distortion + Noise)

12dB/octave Butterworth

variable from 50Hz to 500Hz

20Hz to 20kHz ±1dB

Variable from 150mV to 5V (RCA Input)

NOMAD - Internal analog-computer output protection circuitry

limits power in case of overload, plus short protection.

Thermal switch shuts down the amplifier in case of overheating.

Variable from 0dB to +18dB @ 45Hz and/or

0dB to +12dB @ 12kHz

20K ohms

9 to 16 Volts DC

Yes

>55dB @ 1kHz

>200

< 0.1 @ 2 ohm and < 0.05 @ 4 ohm

These specifications are Amplifier Power Standard CEA-2006 Compliant

Specifications subject to change without notice

10

Image 10
Contents Installation Operation Table of Contents IntroductionSafety Instructions Contents of Carton12 13 Design Features11 13 Installation Installation Considerations Battery and Charging Installation Mounting LocationsWiring the System Bridged Mono Wiring InstallationConnection Operation Channel Wiring P200-2Adjusting Crossover Frequency Remote Punch EQ OptionOperation Adjusting Gain TroubleshootingSpecifications subject to change without notice SpecificationsMODEL- Punch P200-2 P300-2 P400-2 Length of Warranty Limited Warranty InformationFrançais Table DES MatièresConsignes DE Sécurité Contenu DE LemballageParticularités Techniques Installation Considérations Concernant L’INSTALLATION Batterie ET Charge Installation Emplacements DE MontageCâblage DU Système Connexion Dalimentation Ponté MonoFonctionnement Télécommande Dégaliseur Punch en optionCâblage à 2 voies Égaliseur PunchProcédure 2 Le voyant de protection ou thermique est allumé Réglage DU GainDépannage Procédure 3 Vérifiez la sortie audio de lampliModèle Punch P200-2 P300-2 P400-2 CaractéristiquesLes spécifications sont sujettes à changements sans préavis Durée de la garantie Informations SUR LA Garantie LimitéeIntroducción Índice DE MateriasInstrucciones DE Seguridad Contenido DE LA CajaCaracterísticas DEL Diseño Instalación Consideraciones Para LA Instalación Bateríay Carga Instalación Lugares DE MontajeCableado DEL Sistema Conexión de Corriente InstalaciónMono Ponteado Remote Punch EQ Opcional FuncionamientoCableado de 2 canales Ajuste DE LA Frecuencia X-OVER TransiciónCrossover Switch Solución DE ProblemasFuncionamiento Ajuste DE Ganancia Especificaciones Modelo Punch P200-2 P300-2 P400-2Duración de la garantía Información Sobre LA Garantía LimitadaEinleitung InhaltsverzeichnisSicherheitshinweise Inhalt DES KartonsDesigncharakteristiken Einbau Einbauüberlegungen Befolgen Sie vor dem Einbau diese einfachen RegelnBatterie UND Aufladung EinbauBefestigungsstellen Verkabelung DES SystemsStromanschlüsse Mono ÜberbrücktCROSSOVER-FREQUENZ Einstellen ZweikanalverkabelungPUNCH-EQ-FERNBEDIENUNG wahlweise Bringen Sie Schnell AnVerfahren 2Schutz- oderThermallicht leuchtet auf Betrieb Lautstärke Gain EinstellenFehlerbeseitigung Verfahren 3DenVerstärker aufAudioleistung überprüfenMODELL- Punch P200-2 P300-2 P400-2 OrerTechnische Daten Die technischen Daten können sich ohne Ankündigung ändernLaufzeit der Garantie Informationen ZUR Beschränkten GarantieIntroduzione IndiceIstruzioni DI Sicurezza Contenuto DELL’IMBALLAGGIOCaratteristiche DEL Design Installazione Considerazioni SULL’INSTALLAZIONE Batteria E Caricamento Installazione PosizionamentoCablaggio DEL Sistema Collegamento Alla tensione InstallazioneMono Parallelo Equalizzatore Puncha Distanza opzionale Cablaggio a 2 canaliFunzionamento Equalizzatore PunchOppure Funzionamento Regolazione DEL GuadagnoINDIVIDUAZIONE/RIPARAZIONE Guasti Procedura 3Controllare le uscite audio dell’amplificatoreModello Punch P200-2 P300-2 P400-2 SpecificheSpecifiche soggette a modiche senza preavviso Lunghezza della garanzia Informazioni Inerenti Alla Garanzia LimitataInstallation assistance availible at Rockford Fosgate

p3002 specifications

The Rockford Fosgate P3002 is a high-performance two-channel amplifier that stands out in the competitive world of car audio systems. Renowned for its power and sound quality, this amplifier is designed to deliver robust performance for both casual listeners and audiophiles alike.

One of the key features of the P3002 is its compact size. Measuring just 9.25 inches in width, it can easily fit in tight spaces without compromising the audio output. Designed with versatility in mind, it can be used to power a pair of speakers or an entire sound system. The amplifier offers a power output of 50 watts RMS per channel at 4 ohms, and it can deliver 75 watts RMS per channel at 2 ohms. This flexible power rating allows users to choose the ideal configuration for their specific audio setup.

The P3002 integrates advanced technologies that enhance both performance and reliability. One standout feature is the built-in thermal protection circuit, which ensures that the amplifier operates efficiently even under high load conditions. This helps prevent damage from overheating, prolonging the amplifier’s lifespan. Additionally, it includes short-circuit and over-voltage protection, making it a reliable choice for car audio systems.

Sound quality is paramount, and the P3002 does not disappoint. It features high and low-pass crossover settings, allowing users to tailor their sound experience. This flexibility lets audiophiles focus on their preferred frequencies, whether they want deep bass or crisp highs. Furthermore, with a signal-to-noise ratio of 80dB, it minimizes unwanted noise and distortion, ensuring a clean and powerful audio experience.

Durability is another hallmark of the P3002, with a chassis designed to withstand the rigors of daily use. Its sleek silver finish not only enhances aesthetics but also promotes heat dissipation. The amplifier’s RCA inputs make integration with factory systems straightforward, providing versatility for installation.

With a perfect combination of features, technologies, and characteristics, the Rockford Fosgate P3002 amplifier is a compelling choice for anyone looking to enhance their car audio experience. Its strong build quality, impressive power output, and sound customization options make it a standout in its category. Whether you’re a casual listener or a serious enthusiast, the P3002 is designed to elevate your music enjoyment on the road.