Rockford Fosgate p3002 manual Installation Installation Considerations

Page 5

DESIGN FEATURES

12.RCA Input Jacks –The industry standard RCA jacks provide an easy connection for signal level input. They are nickel-plated to resist the signal degradation caused by corrosion.

13.REM Terminal –The heavy duty,nickel-plated captive c-clamp wire connector will accept wire sizes from 12 AWG to 24 AWG.This terminal is used to remotely turn-on and turn-off the amplifier when +12V DC is applied.

14.Power Terminals –The power and ground are nickel-plated captive c-clamp wire connectors and will accommodate up to 4 AWG wire.

INSTALLATION

INSTALLATION CONSIDERATIONS

The following is a list of tools needed for installation:

Fuse-holder and fuse.

(See specifications for fuse rating)

Volt/Ohm Meter

Wire strippers

Wire crimpers

Wire cutters

#2 Phillips screwdriver

Battery post wrench

Hand held drill w/assorted bits

1/8" diameter heatshrink tubing

Assorted connectors

Adequate Length—Red Power Wire

Adequate Length—Remote Turn-on Wire

Adequate Length—Black Grounding Wire

NOTE:We recommend a 4 AWG wire for use on the power (B+) and ground (GND) connections.

This section focuses on some of the vehicle considerations for installing your new amplifier. Pre-planning your system layout and best wiring routes will save installation time.When deciding on the layout of your new system, be sure that each component will be easily accessible for making adjustments.

CAUTION:If you feel unsure about installing this system yourself, have it installed by a qualified technician.

CAUTION:Before installation, disconnect the battery negative (-) terminal to prevent damage to the unit, fire and/or possible injury.

Before beginning any installation, follow these simple rules:

1.Be sure to carefully read and understand the instructions before attempting to install the unit.

2.For safety, disconnect the negative lead from the battery prior to beginning the installation.

3.For easier assembly, we suggest you run all wires prior to mounting your unit in place.

4.Route all of the RCA cables close together and away from any high current wires.

5.Use high quality connectors for a reliable installation and to minimize signal or power loss.

6.Think before you drill! Be careful not to cut or drill into gas tanks, fuel lines, brake or hydraulic lines, vacuum lines or electrical wiring when working on any vehicle.

7.Never run wires underneath the vehicle. Running the wires inside the vehicle provides the best protection.

8.Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through metal, especially the firewall.

9.ALWAYS protect the battery and electrical system from damage with proper fusing. Install the appropriate fuse holder and fuse on the +12V power wire within 18" (45.7 cm) of the battery terminal.

10.When grounding to the chassis of the vehicle, scrape all paint from the metal to ensure a good, clean ground connection. Grounding connections should be as short as possible and always be connected to metal that is welded to the main body, or chassis, of the vehicle.

5

Image 5
Contents Installation Operation Introduction Table of ContentsContents of Carton Safety Instructions11 13 Design Features12 13 Installation Installation Considerations Wiring the System Installation Mounting LocationsBattery and Charging Connection InstallationBridged Mono Wiring Adjusting Crossover Frequency Channel Wiring P200-2Operation Remote Punch EQ OptionTroubleshooting Operation Adjusting GainMODEL- Punch P200-2 P300-2 P400-2 SpecificationsSpecifications subject to change without notice Limited Warranty Information Length of WarrantyTable DES Matières FrançaisContenu DE Lemballage Consignes DE SécuritéParticularités Techniques Installation Considérations Concernant L’INSTALLATION Câblage DU Système Installation Emplacements DE MontageBatterie ET Charge Ponté Mono Connexion DalimentationCâblage à 2 voies Télécommande Dégaliseur Punch en optionFonctionnement Égaliseur PunchDépannage Réglage DU GainProcédure 2 Le voyant de protection ou thermique est allumé Procédure 3 Vérifiez la sortie audio de lampliLes spécifications sont sujettes à changements sans préavis CaractéristiquesModèle Punch P200-2 P300-2 P400-2 Informations SUR LA Garantie Limitée Durée de la garantieÍndice DE Materias IntroducciónContenido DE LA Caja Instrucciones DE SeguridadCaracterísticas DEL Diseño Instalación Consideraciones Para LA Instalación Cableado DEL Sistema Instalación Lugares DE MontajeBateríay Carga Mono Ponteado InstalaciónConexión de Corriente Cableado de 2 canales FuncionamientoRemote Punch EQ Opcional Ajuste DE LA Frecuencia X-OVER TransiciónFuncionamiento Ajuste DE Ganancia Solución DE ProblemasCrossover Switch Modelo Punch P200-2 P300-2 P400-2 EspecificacionesInformación Sobre LA Garantía Limitada Duración de la garantíaInhaltsverzeichnis EinleitungInhalt DES Kartons SicherheitshinweiseDesigncharakteristiken Befolgen Sie vor dem Einbau diese einfachen Regeln Einbau EinbauüberlegungenBefestigungsstellen EinbauBatterie UND Aufladung Verkabelung DES SystemsMono Überbrückt StromanschlüssePUNCH-EQ-FERNBEDIENUNG wahlweise ZweikanalverkabelungCROSSOVER-FREQUENZ Einstellen Bringen Sie Schnell AnFehlerbeseitigung Betrieb Lautstärke Gain EinstellenVerfahren 2Schutz- oderThermallicht leuchtet auf Verfahren 3DenVerstärker aufAudioleistung überprüfenTechnische Daten OrerMODELL- Punch P200-2 P300-2 P400-2 Die technischen Daten können sich ohne Ankündigung ändernInformationen ZUR Beschränkten Garantie Laufzeit der GarantieIndice IntroduzioneContenuto DELL’IMBALLAGGIO Istruzioni DI SicurezzaCaratteristiche DEL Design Installazione Considerazioni SULL’INSTALLAZIONE Cablaggio DEL Sistema Installazione PosizionamentoBatteria E Caricamento Mono Parallelo InstallazioneCollegamento Alla tensione Funzionamento Cablaggio a 2 canaliEqualizzatore Puncha Distanza opzionale Equalizzatore PunchINDIVIDUAZIONE/RIPARAZIONE Guasti Funzionamento Regolazione DEL GuadagnoOppure Procedura 3Controllare le uscite audio dell’amplificatoreSpecifiche soggette a modiche senza preavviso SpecificheModello Punch P200-2 P300-2 P400-2 Informazioni Inerenti Alla Garanzia Limitata Lunghezza della garanziaRockford Fosgate Installation assistance availible at

p3002 specifications

The Rockford Fosgate P3002 is a high-performance two-channel amplifier that stands out in the competitive world of car audio systems. Renowned for its power and sound quality, this amplifier is designed to deliver robust performance for both casual listeners and audiophiles alike.

One of the key features of the P3002 is its compact size. Measuring just 9.25 inches in width, it can easily fit in tight spaces without compromising the audio output. Designed with versatility in mind, it can be used to power a pair of speakers or an entire sound system. The amplifier offers a power output of 50 watts RMS per channel at 4 ohms, and it can deliver 75 watts RMS per channel at 2 ohms. This flexible power rating allows users to choose the ideal configuration for their specific audio setup.

The P3002 integrates advanced technologies that enhance both performance and reliability. One standout feature is the built-in thermal protection circuit, which ensures that the amplifier operates efficiently even under high load conditions. This helps prevent damage from overheating, prolonging the amplifier’s lifespan. Additionally, it includes short-circuit and over-voltage protection, making it a reliable choice for car audio systems.

Sound quality is paramount, and the P3002 does not disappoint. It features high and low-pass crossover settings, allowing users to tailor their sound experience. This flexibility lets audiophiles focus on their preferred frequencies, whether they want deep bass or crisp highs. Furthermore, with a signal-to-noise ratio of 80dB, it minimizes unwanted noise and distortion, ensuring a clean and powerful audio experience.

Durability is another hallmark of the P3002, with a chassis designed to withstand the rigors of daily use. Its sleek silver finish not only enhances aesthetics but also promotes heat dissipation. The amplifier’s RCA inputs make integration with factory systems straightforward, providing versatility for installation.

With a perfect combination of features, technologies, and characteristics, the Rockford Fosgate P3002 amplifier is a compelling choice for anyone looking to enhance their car audio experience. Its strong build quality, impressive power output, and sound customization options make it a standout in its category. Whether you’re a casual listener or a serious enthusiast, the P3002 is designed to elevate your music enjoyment on the road.