Rockford Fosgate FFX3 manual Troubleshooting, Procedure 1 Check Amplifier for proper connections

Page 11

TROUBLESHOOTING

NOTE: If you are having problems after installation follow the Troubleshooting procedures below.

If the display reads "Memory Error" or is difficult to read, see Display Problems at bottom.

Procedure 1: Check Amplifier for proper connections.

Verify that the LCD Display comes on. If it is on, skip to Step 2, if not continue.

1.Check in-line fuse on battery positive cable. Replace if necessary.

2.Verify that Ground connection is connected to clean metal of the vehicle’s chassis. Repair/replace if necessary.

3.Verify there is 10.5 - 15.5 Volts present at the positive battery and remote turn-on cable. Verify quality connections for both cables at amplifier, source unit, and battery/fuseholder. Repair/replace if necessary.

Procedure 2: Check Amplifier for audio output.

1.Verify good RCA input connections at source unit and amplifier. Check entire length of cables for kinks, splices, etc. Test RCA inputs for AC current with source unit on. Repair/replace if necessary.

2.Disconnect RCA input from amplifier. Connect RCA input from test source unit directly to amplifier input.

Procedure 3: Check Amplifier if you experience excess Engine Noise.

1. Route all signal carrying wires (RCA, Speaker cables) away from power and ground wires.

OR

2.Bypass any and all electrical components between the source unit and the amplifier(s). Connect source unit directly to input of amplifier. If noise goes away the unit being bypassed is the cause of the noise.

OR

3.Remove existing ground wires for all electrical components. Reground wires to different locations. Verify that grounding location is clean, shiny metal free of paint, rust etc.

OR

4.Add secondary ground cable from negative battery terminal to the chassis metal or engine block of vehicle.

OR

5.Have alternator and battery load tested by your mechanic. Verify good working order of vehicle electrical system including distributor, spark plugs, spark plug wires, voltage regulator etc.

DISPLAY PROBLEMS

Display hard to read: Insert a small flat bladed screwdriver into the hole above the display screen. While viewing the display, turn the adjuster either way until the display is easily visible.

Display reads "Memory Error": If this occurs, the current settings in the amplifier will automatically reset to the factory defaults except for the INPUT LEVEL, which will set to Ø (mute) to protect the system components. Readjust the amplifier settings and then reset the INPUT LEVEL as needed before operating the amplifier. If the memory error still occurs after readjusting and saving settings, contact Rockford Technical Support. Settings saved in GLOBAL SAVE will not be affected.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents FFX3 Introduction Table of ContentsContents of Carton Safety InstructionsTop Amplifier Design FeaturesInstallation Installation Considerations Engine Compartment InstallationMounting Locations Mounting AmplifierWiring the System Installation Battery and ChargingPower Connection Bridged/Mono Wiring Channel Wiring DSP Button Functions Operation DSP FeaturesOperation Example of making DSP adjustmentsAllen Screw Muting the AmplifierColor Options Display Problems TroubleshootingProcedure 1 Check Amplifier for proper connections Procedure 2 Check Amplifier for audio outputColor Options AccessoriesSpecifications Connecting Punch CapacitorsLimited Warranty Information Length of WarrantyTable DES Matières FrançaisContenu DE Lemballage Consignes DE SécuritéDessus de Lampli Installation Considérations Concernant L’INSTALLATIONParticularités Techniques Montage dans le coffre de préférence et lhabitacle passager Emplacements DE MontageMontage DE Lampli Câblage DU Système Installation Batterie ET ChargeConnexion Dalimentation Câblage ponté/mono Câblage à 2 voies Fonctions DES Boutons DU DSP Fonctionnement Caractéristiques DU DSPExemple dajustements du DSP Cet exemple montre comment ajuster le mode XoverFonctionnement Sauvegarde des paramètres Mise EN Sourdine DE LampliChoix DE Couleur Vis AllenProblèmes Daffichage DépannageProcédure 2 vérifiez la sortie audio de l’ampli Choix de couleur AccessoiresCaractéristiques Condensateurs de connexion PunchGarantie Limitée Durée de la garantieÍndice DE Materias IntroducciónInstrucciones DE Seguridad InicioInstalación Consideraciones Sobre LA Instalación Características DEL DiseñoParte superior del Amplificador Compartimento del motor Lugares DE MontajeMontaje DEL Amplificador Cableado DEL Sistema Instalación Batería Y CargaInstalación Menú Y Ajustes Predeterminados DE DSP Operación Características DEL DSPEjemplo de ajustes de DSP OperaciónTornillo Allen Enmudecimiento DEL AmplificadorOpciones DE Colores Problemas DE Pantalla Solución DE ProblemasOpciones de Colores AccessoriosEspecificaciones Capacitores conectores PunchInformación Sobre LA Garantía Limitada Amplificadores POWER-2 añosAmplificadores Type RF-3 añosInhaltsverzeichnis EinleitungAm Gerät, Feuer bzw. mögliche Verletzungen zu vermeiden SicherheitshinweiseEinbau Einbauüberlegungen DesigncharakteristikenOberseite des Verstärkers Motorraum EinbauBefestigungsstellen Befestigung DES VerstärkersVerkabelung DES Systems Einbau Batterie UND AufladungÜberbrückte bzw. Monoverkabelung StromanschlussZweikanalverkabelung DSP-KNOPFFUNKTIONEN Betrieb DSP-CHARAKTERISTIKENCROSSOVER-MODUS gezeigt BetriebBeispiel der DSP-Einstellung An den Ecken wechseln. Erhältlich auf unserer Dämpfung DES VerstärkersFarboptionen InbusschraubeOder Probleme MIT DER AnzeigeFehlerbeseitigung Verfahren 2 Die Audioleistung des Verstärkers prüfenFarboptionen ZubehörTechnische Daten Punch Kondensatoren anschließenInformationen ZUR Beschränkten Garantie Laufzeit der GarantieLimitata IntroduzioneIndice Contenuto DELL’IMBALLAGGIO Istruzioni DI SicurezzaSommità Dell’amplificatore Installazione Considerazioni SULL’INSTALLAZIONECaratteristiche DEL Design Scompartimento del motore InstallazionePosizionamento Fissaggio DELL’AMPLIFICATORECablaggio DEL Sistema Installazione Batteria E CaricamentoCollegamento alla tensione Channel Bridged monoFunzioni DEI Tasti DEL DSP Funzionamento Caratteristiche DEL DSPEsempio di regolazioni del DSP FunzionamentoMemorizzazione delle impostazioni Silenziamento DELL’AMPLIFICATOREOpzioni PER IL Colore Vite Vite ad esagono IncassatoProcedura 2 Controllate le uscite audio dell’amplificatore Problemi AL DisplayINDIVIDUAZIONE/RIPARAZIONE Guasti Opzioni relative al colore AccessoriCondensatori della Connecting Punch SpecificheInformazioni Inerenti Alla Garanzia Limitata Lunghezza della garanziaNota Nota Rockford Fosgate

FFX3 specifications

The Rockford Fosgate FFX3 is a powerful and versatile amplifier designed to elevate the audio experience in vehicles. Known for its exceptional build quality and performance, the FFX3 is tailored for those who demand clarity and punch from their sound systems. One of the key features of the FFX3 is its Class D amplifier topology, which allows it to deliver significant power output while maintaining high efficiency. This means less heat production and greater reliability, making it ideal for extended listening sessions.

The FFX3 boasts a maximum power output of up to 1,000 watts, enabling it to drive subwoofers and speakers with ease. It comes equipped with a variable low-pass filter that enables users to tailor their sound to perfection, ensuring that the bass is tight and well-defined. Additionally, the amplifier includes high-level inputs, making it compatible with factory-installed audio systems without the need for a signal converter. This flexibility allows users to upgrade their audio systems without extensive modifications.

One of the standout technologies in the FFX3 is its "on-board" signal processing capabilities. The amplifier features adjustable bass boost, allowing listeners to enhance lower frequencies to suit their personal preferences. Moreover, the FFX3 incorporates a thermal protection circuit, safeguarding the amplifier against overheating during intense use. The compact design of the FFX3 makes it easy to install in a variety of locations within a vehicle, ensuring that space constraints won’t be an issue.

The chassis of the FFX3 is rugged and designed to withstand the rigors of automotive environments. Its stylish aesthetics allow it to seamlessly integrate into any car interior while remaining unobtrusive. Further enhancing its versatility, the amplifier includes a remote bass level control, allowing users to adjust their bass output from the front seat for maximum convenience.

In conclusion, the Rockford Fosgate FFX3 is a powerful and efficient audio amplifier that excels in delivering high-quality sound. With its innovative features and solid construction, it is a perfect choice for anyone looking to upgrade their vehicle's audio system. Whether attentive to detail or seeking high-impact bass, the FFX3 promises to enhance any listening experience.
Top Page Image Contents