Dell DCSM specifications Installing the Processor

Page 37

4 release lever

NOTICE: When replacing the processor, do not touch any of the pins inside the socket or allow any objects to fall on the pins in the socket.

5.Gently remove the processor from the socket.

Leave the release lever extended in the release position so that the socket is ready for the new processor.

Installing the Processor

NOTICE: Ground yourself by touching an unpainted metal surface on the back of the computer.

NOTICE: When replacing the processor, do not touch any of the pins inside the socket or allow any objects to fall on the pins in the socket.

1. Unpack the new processor, being careful not to touch the underside of the processor.

NOTICE: You must position the processor correctly in the socket to avoid permanent damage to the processor and the computer when you turn on the computer.

2.If the release lever on the socket is not fully extended, move it to that position.

3.Orient the front and rear alignment notches on the processor with the front and rear alignment notches on the socket.

4.Align the pin-1 corners of the processor and socket.

1

processor cover

6

release lever

 

 

 

 

2

tab

7

front alignment notch

 

 

 

 

3

processor

8

socket and processor pin-1 indicator

 

 

 

 

4

processor socket

9

rear alignment notch

 

 

 

 

5

center cover latch

 

 

NOTICE: To avoid damage, ensure that the processor aligns properly with the socket, and do not use excessive force when you install the processor.

5.Set the processor lightly in the socket and ensure that the processor is positioned correctly.

6.When the processor is fully seated in the socket, close the processor cover.

Ensure that the tab on the processor cover is positioned underneath the center cover latch on the socket.

7.Pivot the socket release lever back toward the socket and snap it into place to secure the processor.

NOTICE: If you are not installing a processor upgrade kit from Dell, reuse the original heat sink assembly when you replace the processor.

If you installed a processor replacement kit from Dell, return the original heat sink assembly and processor to Dell in the same package in which your replacement kit was sent.

8. Install the heat sink assembly:

Image 37
Contents Abbreviations and Acronyms Front View of Computer About Your Dell Dimension 5000 ComputerLights Back View of ComputerBack to Contents Dell Diagnostics Advanced TroubleshootingWhen to Use the Dell Diagnostics Starting the Dell Diagnostics From Your Hard DrivePower Light Problem Description Suggested Resolution Dell Diagnostics Main MenuSystem Lights Option FunctionLight Pattern Problem Description Suggested Resolution Diagnostic LightsCode Cause Beep CodesBack to Contents Getting Started Before You BeginRecommended Tools Turning Off Your ComputerBack to Contents Replacing the Computer Cover Removing the Computer Cover Memory Removing and Installing PartsDDR2 Memory Overview Installing Memory Addressing Memory With 4-GB ConfigurationsRemoving Memory CardsPCI Cards Installing a PCI Card Removing a PCI Card PCI Express Cards Installing a PCI Express CardPage Removing a PCI Express Card Removing the Drive Panel Drive PanelsReplacing the Drive-Panel Insert Removing the Drive-Panel InsertReplacing the Drive Panel Drives Drive Interface Connectors Connecting Drive CablesPower Cable Connector Connecting and Disconnecting Drive CablesRemoving a Hard Drive Hard DriveAdding a Second Hard Drive Installing a Hard DriveRemoving a Floppy Drive Floppy DriveInstalling a Floppy Drive Replace the computer cover Removing a Media Card Reader Media Card ReaderRemove the computer cover Installing a Media Card ReaderRemoving a CD/DVD Drive CD/DVD DriveInstalling a CD/DVD Drive Replace the computer cover Removing the Processor ProcessorInstalling the Processor System Board Jumper Setting Description Jumper SettingsRemoving the System Board Removing the Power Supply Power SupplyReplacing the System Board Replacing the Power Supply Replacing the Battery BatterySpecifications Drives ConnectorsControls and Lights Physical PowerEnvironmental Entering System Setup System SetupSystem Setup Screens OverviewPXE. When the On w/ PXE setting is active System Setup OptionsUSB, Internal, or Read Only COM3Are every day or every Monday through Friday System Password optionOption Settings Boot SequenceChanging Boot Sequence for the Current Boot Changing Boot Sequence for Future BootsClearing Cmos Settings Clearing Forgotten PasswordsBack to Contents Inside View of Your Computer System Board Components Technical OverviewDC Power Connector P1 Power Supply DC Connector Pin AssignmentsCOM Pin Number Signal Name 18-AWG WireAbbreviations and Acronyms
Related manuals
Manual 217 pages 3.31 Kb Manual 158 pages 23.31 Kb Manual 72 pages 7.23 Kb