Nortel Networks 2700 manual 1000BASE-T or 1000BASE-SX interface

Page 67

 

 

Chapter 4 Installing option cards and DIMMs 67

 

 

Table 17 Installing other option cards with the SSL VPN Module 1000 (continued)

 

 

Option card

Restrictions with SSL VPN Module 1000 installed

 

 

1000BASE-T or 1000BASE-SX interface

You can install two cards only if none of these cards is installed:

 

• VPN Router Security Accelerator

 

Hardware Accelerator

 

HSSI

 

If a VPN Router Security Accelerator, Hardware Accelerator, or

 

HSSI card is installed, only one 1000BASE-T (1000 MT) or

 

1000BASE-SX card can be installed.

V.90 modem interface

Do not install this card in slot 2.

 

 

HSSI WAN interface

Only one HSSI card can be installed. Install this card in slot 3 if

 

possible. Do not install this card in slot 4.

To install or replace an interface card or a VPN Accelerator card (VPN Router Security Accelerator card or Hardware Accelerator card):

1Shut down the VPN Router 2700 using the Web GUI or the CLI, and then unplug it as described in “Shutting down the system to add or replace hardware” on page 60.

Warning: Risk of electric shock

Turn off the VPN Router 2700 and unplug it before you attempt to install an option card.

2Remove the front bezel from the chassis, and then remove the chassis from the equipment rack (see “Removing the front bezel and top cover” on page 61).

3Remove the top cover from the chassis (see “Removing the front bezel and top cover” on page 61).

4Attach the antistatic wrist strap that was shipped with the VPN Router 2700 (see “Attaching the antistatic wrist strap” on page 64).

5Locate the slot where you plan to install the new or replacement option card.

Note: Do not try to install an HSSI WAN interface card or a Hardware

Accelerator card in slot 4.

Nortel VPN Router Installation — VPN Router 2700

Image 67
Contents Nortel VPN Router Installation NN46110-311 Copyright 2007 Nortel Networks. All rights reservedEC Declaration of Conformity Nortel VPN Router Installation VPN RouterCanada requirements only General NN46110-311 Contents Contents Chapter Cabling the VPN Router and turning the power onAppendix a Contents NN46110-311 Figures Figures Tables Tables New in this release Features1000BASE-T 1000 GT Ethernet card New in this release NN46110-311 Finding the latest updates on the Nortel Web site How to get helpGetting help from the Nortel Web site How to get help Getting help over the phone from a Nortel Solutions CenterGetting help through a Nortel distributor or reseller How to get help NN46110-311 Before you begin PrefaceAcronyms Text conventionsPreface Nortel VPN Router Security Firewalls, Filters, NAT, and QoS Related publicationsPrinted technical manuals Description of the Nortel VPN Router Chapter Installing the Nortel VPN Router 2700 chassisTopic Installing the Nortel VPN Router 2700 chassis Preparing to install the Nortel VPN RouterShipment contents Site requirements Additional equipmentInstalling the chassis on a flat surface Installing the chassisRack-mount recommendations Installing the chassis in an equipment rackAttaching the cage nuts to the rack Mounting the chassis in the equipment rack Replacing the front bezel Installing the Nortel VPN Router 2700 chassis NN46110-311 Topic Chapter Cabling the VPN Router and turning the power onCabling the VPN Router and turning the power on Connecting communications cablesInterfaces and cables for the VPN Router Rear view of the VPN Router Power cord requirements Connecting the power cordRequirement Description Verifying a successful installation Front panel LEDs Front panel LED indicatorsIndicator Description Understanding the LEDsLEDs on the system 10/100BASE-TX Ethernet port LED indicators on the system 10/100BASE-TX Ethernet port10/100BASE-TX Ethernet interface card LEDs LED indicators on the 10/100BASE-TX Ethernet interface card1000BASE-T 1000 GT Ethernet interface card LEDs LEDs on the 1000BASE-T 1000 MT Ethernet interface card 1000BASE-T 1000 MT Ethernet interface card LEDs1000BASE-SX Ethernet interface card LED LED indicator on the 1000BASE-SX Ethernet interface card56/64K CSU/DSU WAN interface card LEDs LED indicators on the 56/64K CSU/DSU WAN interface cardAdsl WAN interface card LEDs LED indicators on the Adsl WAN interface cardTx/Rx LED Description T1/E1 CSU/DSU WAN interface card LEDs LED indicators on the T1/E1 CSU/DSU WAN interface cardQuad T1/E1 CSU/DSU WAN interface card LEDs LED indicators on the quad T1/E1 CSU/DSU WAN interface cardSingle V.35/X.21 WAN interface card LEDs LED indicators on the single V.35/X.21 WAN interface cardLEDs Indicator Description LED indicators on the SSL VPN ModuleSSL VPN Module 1000 LEDs Chapter Configuring the management IP interface Required information Configuring the management IP interfaceConfiguring the management IP address Enter Old Subnet Mask = 0.0.0.0 New Subnet Mask = Type M, and press Enter Management IP Address prompt appears Testing the configuration Troubleshooting Chapter Installing option cards and DIMMs Shutting down the system to add or replace hardware Installing option cards and DIMMsRemoving the front bezel and top cover Slide the top cover forward approximately 1/4 inch Location of option card slots and DIMMs on the system board Attaching the antistatic wrist strap Supported option cards for the 2600 Installing and replacing option cardsMaximum Option card Number Restrictions Option card Restrictions with SSL VPN Module 1000 installed Installing other option cards with the SSL VPN Module1000BASE-T or 1000BASE-SX interface Installing and removing an option card Press here Installing and replacing DIMMs Installing option cards and DIMMs Installing and removing a Dimm Installing option cards and DIMMs Installing option cards and DIMMs NN46110-311 Specification Description Appendix a Technical specificationsChassis specifications Physical, electrical, and environmental specifications10/100BASE-TX Ethernet LAN port System portsPin Description Appendix a Technical specificationsSerial port 10/100BASE-TX Ethernet port pinoutsMultiple DB9 and DB25 connector pinouts Modem cable specificationsSerial port DB9 connector DB25 connector Hardware option cards Nortel termination Modem termination Signal Pin # to Pin #Modem cable pinouts VPN Router Security Accelerator card VPN Router Security Accelerator cardsSSL VPN Module SSL VPN Module10/100BASE-TX Ethernet interface card 10/100BASE-TX Ethernet interface card1000BASE-T 1000 GT Ethernet interface card 1000BASE-T 1000 GT Ethernet pinouts 1000BASE-T 1000 GT Ethernet interface card1000BASE-T 1000 MTEthernet port pinouts 1000BASE-T 1000 MT Ethernet interface cardNN46110-311 1000BASE-SX Ethernet interface card 1000BASE-SX Ethernet interface card56/64K CSU/DSU WAN interface card 56/64K CSU/DSU WAN interface card56/64K CSU/DSU cable pinouts for straight-through connection Nortel termination Remote termination Signal Pin # to Pin #Adsl cable pinouts Adsl WAN interface cardPin Function Isdn BRI S/T cable pinouts Isdn BRI interface cardIsdn BRI U cable pinouts T1/E1 CSU/DSU WAN interface cardT1/E1 CSU/DSU cable pinouts for crossover connection T1/E1 CSU/DSU WAN interface card full-height cardT1/E1 CSU/DSU cable pinouts for straight-through connection Quad T1/E1 CSU/DSU WAN interface card Quad T1/E1 CSU/DSU WAN interface cardSingle V.35/X.21 WAN interface card Modem interface card90 modem cable pinouts 35 cable pinouts 21 cable pinouts Appendix a Technical specifications 35 cable pinoutsAppendix a Technical specifications 21 cable pinouts Hssi WAN interface card Pin Scsi male Signal nameT3 cable pinouts GND RCA CAA RDA LCA STA TAA TTA LAA TDA LBA Testa Appendix a Technical specifications NN46110-311 Numerics IndexIndex Index Index Index Index
Related manuals
Manual 12 pages 5.25 Kb