Nortel Networks 2700 manual Installing the chassis on a flat surface

Page 29

Chapter 1 Installing the Nortel VPN Router 2700 chassis 29

Installing the chassis

To install the VPN Router 2700, do one of the following:

Position the chassis on a flat, sturdy, horizontal surface.

Mount the chassis in a standard equipment rack (see “Installing the chassis in an equipment rack” on page 30).

Installing the chassis on a flat surface

If you decide to place the VPN Router 2700 on a flat surface, make sure that the surface is large enough for the gateway and sturdy enough to support the combined weight of the VPN Router 2700 and the cables that you attach to it.

The VPN Router 2700 accessory kit includes four rubber feet that can be attached to the bottom of the gateway. Figure 2 shows the placement of these rubber feet.

Figure 2 Placement of rubber feet on the bottom of the chassis

Attach feet (4)

CS160016A

Nortel VPN Router Installation — VPN Router 2700

Image 29
Contents Nortel VPN Router Installation NN46110-311 Copyright 2007 Nortel Networks. All rights reservedEC Declaration of Conformity Nortel VPN Router Installation VPN RouterCanada requirements only General NN46110-311 Contents Contents Chapter Cabling the VPN Router and turning the power onAppendix a Contents NN46110-311 Figures Figures Tables Tables 1000BASE-T 1000 GT Ethernet card FeaturesNew in this release New in this release NN46110-311 Getting help from the Nortel Web site How to get helpFinding the latest updates on the Nortel Web site How to get help Getting help over the phone from a Nortel Solutions CenterGetting help through a Nortel distributor or reseller How to get help NN46110-311 Before you begin PrefacePreface Text conventionsAcronyms Nortel VPN Router Security Firewalls, Filters, NAT, and QoS Related publicationsPrinted technical manuals Topic Chapter Installing the Nortel VPN Router 2700 chassisDescription of the Nortel VPN Router Installing the Nortel VPN Router 2700 chassis Preparing to install the Nortel VPN RouterShipment contents Site requirements Additional equipmentInstalling the chassis on a flat surface Installing the chassisRack-mount recommendations Installing the chassis in an equipment rackAttaching the cage nuts to the rack Mounting the chassis in the equipment rack Replacing the front bezel Installing the Nortel VPN Router 2700 chassis NN46110-311 Topic Chapter Cabling the VPN Router and turning the power onInterfaces and cables for the VPN Router Connecting communications cablesCabling the VPN Router and turning the power on Rear view of the VPN Router Requirement Description Connecting the power cordPower cord requirements Verifying a successful installation Indicator Description Front panel LED indicatorsUnderstanding the LEDs Front panel LEDsLEDs on the system 10/100BASE-TX Ethernet port LED indicators on the system 10/100BASE-TX Ethernet port1000BASE-T 1000 GT Ethernet interface card LEDs LED indicators on the 10/100BASE-TX Ethernet interface card10/100BASE-TX Ethernet interface card LEDs LEDs on the 1000BASE-T 1000 MT Ethernet interface card 1000BASE-T 1000 MT Ethernet interface card LEDs1000BASE-SX Ethernet interface card LED LED indicator on the 1000BASE-SX Ethernet interface card56/64K CSU/DSU WAN interface card LEDs LED indicators on the 56/64K CSU/DSU WAN interface cardTx/Rx LED Description LED indicators on the Adsl WAN interface cardAdsl WAN interface card LEDs T1/E1 CSU/DSU WAN interface card LEDs LED indicators on the T1/E1 CSU/DSU WAN interface cardQuad T1/E1 CSU/DSU WAN interface card LEDs LED indicators on the quad T1/E1 CSU/DSU WAN interface cardSingle V.35/X.21 WAN interface card LEDs LED indicators on the single V.35/X.21 WAN interface cardSSL VPN Module 1000 LEDs LED indicators on the SSL VPN ModuleLEDs Indicator Description Chapter Configuring the management IP interface Required information Configuring the management IP interfaceConfiguring the management IP address Enter Old Subnet Mask = 0.0.0.0 New Subnet Mask = Type M, and press Enter Management IP Address prompt appears Testing the configuration Troubleshooting Chapter Installing option cards and DIMMs Shutting down the system to add or replace hardware Installing option cards and DIMMsRemoving the front bezel and top cover Slide the top cover forward approximately 1/4 inch Location of option card slots and DIMMs on the system board Attaching the antistatic wrist strap Maximum Option card Number Restrictions Installing and replacing option cardsSupported option cards for the 2600 Option card Restrictions with SSL VPN Module 1000 installed Installing other option cards with the SSL VPN Module1000BASE-T or 1000BASE-SX interface Installing and removing an option card Press here Installing and replacing DIMMs Installing option cards and DIMMs Installing and removing a Dimm Installing option cards and DIMMs Installing option cards and DIMMs NN46110-311 Chassis specifications Appendix a Technical specificationsPhysical, electrical, and environmental specifications Specification Description10/100BASE-TX Ethernet LAN port System portsSerial port Appendix a Technical specifications10/100BASE-TX Ethernet port pinouts Pin DescriptionSerial port DB9 connector DB25 connector Modem cable specificationsMultiple DB9 and DB25 connector pinouts Modem cable pinouts Nortel termination Modem termination Signal Pin # to Pin #Hardware option cards VPN Router Security Accelerator card VPN Router Security Accelerator cardsSSL VPN Module SSL VPN Module10/100BASE-TX Ethernet interface card 10/100BASE-TX Ethernet interface card1000BASE-T 1000 GT Ethernet interface card 1000BASE-T 1000 GT Ethernet pinouts 1000BASE-T 1000 GT Ethernet interface card1000BASE-T 1000 MTEthernet port pinouts 1000BASE-T 1000 MT Ethernet interface cardNN46110-311 1000BASE-SX Ethernet interface card 1000BASE-SX Ethernet interface card56/64K CSU/DSU WAN interface card 56/64K CSU/DSU WAN interface card56/64K CSU/DSU cable pinouts for straight-through connection Nortel termination Remote termination Signal Pin # to Pin #Pin Function Adsl WAN interface cardAdsl cable pinouts Isdn BRI S/T cable pinouts Isdn BRI interface cardIsdn BRI U cable pinouts T1/E1 CSU/DSU WAN interface cardT1/E1 CSU/DSU cable pinouts for crossover connection T1/E1 CSU/DSU WAN interface card full-height cardT1/E1 CSU/DSU cable pinouts for straight-through connection Quad T1/E1 CSU/DSU WAN interface card Quad T1/E1 CSU/DSU WAN interface card90 modem cable pinouts Modem interface cardSingle V.35/X.21 WAN interface card 35 cable pinouts 21 cable pinouts Appendix a Technical specifications 35 cable pinoutsAppendix a Technical specifications 21 cable pinouts T3 cable pinouts Pin Scsi male Signal nameHssi WAN interface card GND RCA CAA RDA LCA STA TAA TTA LAA TDA LBA Testa Appendix a Technical specifications NN46110-311 Numerics IndexIndex Index Index Index Index
Related manuals
Manual 12 pages 5.25 Kb