Epson TK14 operation manual ESC 2, ESC, DLE EOT n, = 01H Printer status Bit, Off/On

Page 31

FENIX IMVICO		TK14 OPERATION MANUAL
LF
[Name]	Print and line feed
[Format]	ASCII	LF
	Hex	0A
	Decimal	10
[Description]	Prints the data in the print buffer and feeds one line, based on the current line spacing.
[Note]	This command sets the print position to the beginning of the line.
[Reference]	ESC 2, ESC 3.
CR
[Name]	Print and carriage return
[Format]	ASCII	CR
	Hex	0D
	Decimal	13
[Description]	When automatic line feed is enabled, this command operates the same as LF; when
	automatic line feed is disabled, this command is ignored.
[Notes]

•This command is set at the start-up, via the PROGRAMMING MODE (see point 3.6.2- PROGRAMMING MODE).

•Sets the print starting position to the beginning of the line. [Reference] LF

DLE EOT n

[Name]	Real-time status transmission
[Format]	ASCII	DLE	EOT	n
	Hex	10	04	n
	Decimal	16	04	n
[Range]	<01>H ≤ n ≤	<04>H
[Description]	Transmits the selected printer status specified by n in real-time, according to the following
	parameters:
	n = <01>H: Transmit printer status
	n = <02>H: Transmit offline status

n = <03>H: Transmit error status

n = <04>H: Continuous paper sensor status

n = <05>H: Paper sensor status

[Notes]

•The status is transmitted whenever the data sequence <10>H<04>H<n>

( <01>H ≤ n ≤ <05>H) is received.

•The printer transmits the current status. Each status item is represented by one-byte of data.

•The printer transmits the status without confirming whether the host computer can receive data (in serial interface).

•The printer executes this command upon receiving it.

•This command is executed even when the printer is offline, the receiver buffer is full, or there is an error status with a serial interface model.

•If a not recovery error occurred, the bit 2 in the Printer Status (n=1) will be indeterminate.

n = <01>H: Printer status

	Bit	OFF/ON	Function
	0	OFF	Not used. Fixed to OFF
	1	ON	Not used. Fixed to ON
	2	OFF	Not used. Fixed to OFF
	3	OFF	Online
	3	ON	Offline
		ON	Offline
	4	ON	Not used. Fixed to ON
	5	OFF	Does not wait for online error recovery
		ON	Waits for online error recovery
	6	-	Undefined
	7	OFF	Not used. Fixed to OFF

31/65

Image 31

Contents TK14 Thermal Printer Version 1 Date Febraury Introduction InstallationControl Commands IndexFenix Imvico Figures and Tables Security Precautons Important Notes in TK14 Thermal Printer ManagementRecommendations Cleaning Procedure and PrecautionsIntroduction Printing specifications General SpecificationsCharacter specifications TW80KK-S TF77KS-E2TK14 Installation Considerations InstallationTK14 earth connection Minimal Nozzle Hole Dimension User Front PanelImportant Note about Power Supply Power SupplyGND Change between online and offline mode RS-232 Serial interface specificationsRS-232 Serial Interface PC serial interface connection Serial RS-232 interface pins assignmentSignal FunctionCentronics Parallel Interface PrtBusy/Data3,7 Male DB25 PC parallel interface connectionManual Paper Load Basic OperationsPaper Loading Automatic Paper LoadProg Button Buttons FunctionsPfeed Button Prog Pfeed Button. FunctionsOpen Platen Sensor Self-test modeSpecial Printing Modes Programming Mode Programming modeYES Hexadecimal dump mode Error types Error ProcessingNEAR-END Paper Error No Paper Error Hardware ErrorPower Supply Voltage Error Thermal Head Temperature ErrorImportant Notes Paper JAM ErrorData reception error serial interface only Printer operation when an error happensFlow diagram of the error detection for the serial port END Flow diagram of the error detection for the parallel portControl Comands Command NotationTerm Definitions ESC Description of the Control CommandsDLE EOT ESC SPOFF/ON ESC 2, ESCDLE EOT n = 01H Printer status BitOFF/ON Appendix a Appendix FESC ESC @ ESC M, GS !, Appendix aESC !, ESC G Reference ESC !, Appendix a GS B nESC J n ESC M nOFF / on JustificationABC Abcd Abcde ESC c 3 nESC d n ESC c 5 nESC 2, ESC GS ! n Test pattern ESC !, Appendix aGS a pL pH n m PaperFont GS T nPrinting position GS V mGS f, GS k GS h n GS H nBar Code System Number of Characters Remarks GS h, GS w GS w n Mode Vertical Dot Horizontal Dot DensityModule Width mm for Multi-level Bar Code Mode FS p n mHorizontal Dot Density FS q n xL xH yL yH d1…dk1…xL xH yL yH d1…dk # TW80KK-S Appendix a SpecificationsTL69KS-HG76 TL69KS-R2Autocutter Unit Appendix B IF1500 Connectors and ButtonsLine Thermal Printer Mechanism Appendix C External Appearance FA-40TK Appendix D HOW to OrderPartnumber FAPOS-1Description of the CODE128 Bar Code Appendix E CODE128 BAR CodeHex Decimal Codea DEL7B,42 123,66 52/65 Appendix F Internal Character Tables 0 80H to FFH 17. PC866 Cyrillic 55/65 PC Communication Port Configuration Appendix G Testing SoftwarePrinter Status Sample Ticket 59/65