Siemens CL-110 user manual

Page 16

p

q

r

s

When the welcome screen appears, click Next for next step.

When the InstallShield Wizard Complete appears, click Finish.

Plug the USB cable between your device and PC.

Note: If the USB device is not detected, check the USB cable between the PC and the device. Also verify that the device is power on.

The system will detect the USB driver automatically.

Image 16

Contents User’s Manual Rev 2006/02/09Safety Notes FCC Features PrefaceBridging Features Routing FeaturesSecurity Features Configuration and ManagementUnpacking Subscription for Adsl Service Page LED Indicators OverviewPhysical Outlook Front PanelRear Panel VACSystem Requirement System Requirement and InstallationChoosing a place for the Adsl Router Connecting the Adsl Router For Windows ME Install the USB DriverFor Windows Page For Windows XP Page Uninstall the USB Driver For Windows Configuration Page Configuration For Windows XP Configuration Page Setting TCP/IP Option 1 If you have no TCP/IP protocol, click Add Configuration Page For Windows ME For Windows NT Highlight TCP/IP Protocol and click OKConfiguration Page For Windows Page Option 1 If you have no TCP/IP Protocol, click Install Panel and then click Network Internet ConnectionsProperties Click Internet ProtocolTCP/IP and then click OKConfigure PC to get IP address from Dhcp Enable Obtain an IP address automatically and then click OK Renew IP Address on Client PC For Windows 98MEFor Windows NT For Windows Configuration Connecting and Accessing Internet Configuration PPP over ATM PPPoA ModeDescription PPP over ATM PPPoA IP Extension Mode Go to Advanced Internet Connections. And click AddPPP over Ethernet PPPoE Mode ISPPPP over Ethernet PPPoE IP Extension Mode Numbered IP over ATM IPoA IP Address Subnet Mask Gateway Numbered IP over ATM IPoA+NAT LAN Unnumbered IP over ATM IPoA Primary DNS server Secondary DNS serverIP Address Subnet Mask Gateway Unnumbered IP over ATM IPoA+NAT Primary IP Address Subnet maskPage Bridge Mode Web Configuration Using Web-Based ManagerOutline of Web Manager To Have the New Settings Take EffectLanguage Quick Setup Quick StartConnect to Internet Connection TypeConnection Mode PPP over ATM/ PPP over Ethernet Choose PPPoA or PPPoE and click NextPPP Password PPP UsernameAlways On Dial on DemandLeased Time Dhcp Server OffIP over ATM NoneSubnet Mask Connection Mode Bridging MTU Status OverviewAdsl Line Adsl BER TestInternet Connection Traffic StatisticsDhcp Table Routing TableConnection Mode Local Network- IP Address Advanced SetupLocal Network Dhcp Server Relay On Server and Relay OffPage Internet-Connections Setting Local Network UPnPAdding a New One VPI Virtual Path IdentifierPage Igmp Proxy Enabled Internet-DNS ServerInternet-IGMP Proxy Internet ConnectionInternet Adsl Settings IP Routing Static RouteConfiguring Other Routers on Your LAN Gateway IP AddressRemove Static Route DestinationOperation Mode EnabledIP Routing Dynamic Routing Adsl RouterConnection Mode Virtual Server-Port Forwarding Pre-defined IP Address seen by Internet UsersUser defined Virtual Server-Port Triggering Connecting to the Virtual ServersFrom Internet Host IP Address Virtual Server DMZ Host Virtual Server Dynamic DNS Filtering by IP address FirewallSelect the direction to filter packets Allow Traffic ProtocolSource/Destination IP address Port RangeQuality of Service Bridge QoSIP type of Service IPQoSSource IP Address/ Subnet Mask Source PortDestination Port Port MappingVoice Quality Group Name Available InterfacesDiagnostics ManagementAdmin Account Remote AccessInterntet Time Configure System LogSystem Log Viewing System Log Snmp Setting Update Firmware Backup ConfigReset Router UPnP for XP Page Problems with LAN TroubleshootingProblems with WAN Problems with Upgrading ARP Address Resolution Protocol GlossaryVPI Virtual Path Identifier & VCI Virtual Channel Identifier Glossary Page Appendix a Specifications Interface One RJ-11 port for Adsl connectionPage Appendix B Server Setup for 802.1x Client Getting Client CertificateYes Appendix C Weee B2C