Siemens CL-110 user manual Setting TCP/IP

Page 25

Chapter 3: Configuration

p

q

The InstallShield Wizard dialog will appear.

Unplug the USB cable between your device and your PC. Then click OK.

rWhen the Maintenance Complete screen appears, the USB driver is removed successfully. Click Finish.

Setting TCP/IP

In order to access the Internet through the router, each host on your network must install/setup TCP/IP. Please follow the steps below for select a network adapter.

Image 25

Contents Rev 2006/02/09 User’s ManualSafety Notes FCC Preface FeaturesRouting Features Bridging FeaturesSecurity Features Configuration and ManagementUnpacking Subscription for Adsl Service Page Overview LED IndicatorsPhysical Outlook Front PanelVAC Rear PanelSystem Requirement System Requirement and InstallationChoosing a place for the Adsl Router Connecting the Adsl Router For Windows ME Install the USB DriverFor Windows Page For Windows XP Page Uninstall the USB Driver For Windows Configuration Page Configuration For Windows XP Configuration Page Setting TCP/IP Option 1 If you have no TCP/IP protocol, click Add Configuration Page For Windows ME Highlight TCP/IP Protocol and click OK For Windows NTConfiguration Page For Windows Page Panel and then click Network Internet Connections Option 1 If you have no TCP/IP Protocol, click InstallProperties Click Internet ProtocolTCP/IP and then click OKConfigure PC to get IP address from Dhcp Enable Obtain an IP address automatically and then click OK For Windows 98ME Renew IP Address on Client PCFor Windows NT For Windows Configuration Connecting and Accessing Internet Configuration PPP over ATM PPPoA ModeDescription Go to Advanced Internet Connections. And click Add PPP over ATM PPPoA IP Extension ModeISP PPP over Ethernet PPPoE ModePPP over Ethernet PPPoE IP Extension Mode Numbered IP over ATM IPoA IP Address Subnet Mask Gateway Numbered IP over ATM IPoA+NAT LAN Primary DNS server Secondary DNS server Unnumbered IP over ATM IPoAIP Address Subnet Mask Gateway Primary IP Address Subnet mask Unnumbered IP over ATM IPoA+NATPage Bridge Mode Using Web-Based Manager Web ConfigurationOutline of Web Manager To Have the New Settings Take EffectLanguage Quick Start Quick SetupConnect to Internet Connection TypeConnection Mode Choose PPPoA or PPPoE and click Next PPP over ATM/ PPP over EthernetPPP Username PPP PasswordAlways On Dial on DemandDhcp Server Off Leased TimeNone IP over ATMSubnet Mask Connection Mode Bridging MTU Overview StatusAdsl BER Test Adsl LineTraffic Statistics Internet ConnectionDhcp Table Routing TableConnection Mode Local Network- IP Address Advanced SetupLocal Network Dhcp Server Server and Relay Off Relay OnPage Local Network UPnP Internet-Connections SettingAdding a New One VPI Virtual Path IdentifierPage Internet-DNS Server Igmp Proxy EnabledInternet-IGMP Proxy Internet ConnectionIP Routing Static Route Internet Adsl SettingsGateway IP Address Configuring Other Routers on Your LANRemove Static Route DestinationEnabled Operation ModeIP Routing Dynamic Routing Adsl RouterConnection Mode Virtual Server-Port Forwarding Pre-defined IP Address seen by Internet UsersUser defined Virtual Server-Port Triggering Connecting to the Virtual ServersFrom Internet Host IP Address Virtual Server DMZ Host Virtual Server Dynamic DNS Filtering by IP address FirewallSelect the direction to filter packets Protocol Allow TrafficSource/Destination IP address Port RangeBridge QoS Quality of ServiceIPQoS IP type of ServiceSource IP Address/ Subnet Mask Source PortDestination Port Port MappingVoice Quality Available Interfaces Group NameManagement DiagnosticsRemote Access Admin AccountInterntet Time Configure System LogSystem Log Viewing System Log Snmp Setting Update Firmware Backup ConfigReset Router UPnP for XP Page Problems with LAN TroubleshootingProblems with WAN Problems with Upgrading Glossary ARP Address Resolution ProtocolVPI Virtual Path Identifier & VCI Virtual Channel Identifier Glossary Page Interface One RJ-11 port for Adsl connection Appendix a SpecificationsPage Getting Client Certificate Appendix B Server Setup for 802.1x ClientYes Appendix C Weee B2C