Toshiba e-STUDIO166, e-STUDIO206 manual General Precautions, When installing or moving

Page 16

General Precautions

When installing or moving

Warning

yThis equipment requires 220 to 240 V AC, 8 A 50/60 Hz electric power. Do not use a power supply with a voltage other than that specified.

Avoid multiple connections in the same outlet. This could cause a fire or give you an electric shock. If you are considering increasing the number of outlets, contact an electrician.

yAlways connect this equipment to an outlet with an earth connection to avoid the danger of fire or electric shock in case of short-circuiting. Contact your service representative for the details. Be sure to use a 3-conductor, grounded wall outlet.

In areas, where a 2-pin plug is used, the equipment must be grounded for safety. Never ground it to a gas pipe, a water pipe, or any other object not suitable for grounding.

yPlug the power cable securely into the outlet. If it is not plugged in properly, it could heat up and cause a fire or give you an electric shock.

yDo not damage, break or attempt to repair the power cable. The following things should not be done to the power cable.

-Twisting it

-Bending it

-Pulling it

-Placing anything on it

-Making it hot

-Situating it near radiators or other heat sources

This could cause a fire or give you an electric shock. If the power cable is damaged, contact your service representative.

yDo not install the equipment by yourself or try to move it once it has been installed. This could result in an injury or damage to the device. Contact your service representative if the equipment needs to be installed or moved.

yPull the plug out from the outlet more than once a year to clean around the prongs. Accumu- lating dust and dirt could cause a fire due to the heat released by electric leakage.

14 General Precautions

Image 16

Contents Operators Manual for Copying Functions Page Preface PrefaceFor Germany only Working environmentPage Before Reading This Manual Lineup of our manualsHow to read this manual Signal in this manual Description of original/paper directionTrademarks Contents Copying in Same Page Order as Originals Sort Copying 100Cleaning charger 101 Cleaning transfer charger 102 111Contents Toshiba Quality Is Second to None Recommended toner cartridgesCartridge detecting function Toner remaining check functionToner Supplies / PartsGeneral Functions extended by various options Features of e-STUDIO166/206Ecological energy-saving design General Precautions When installing or movingOther points 10 cm 80 cmWhen using the equipment Position of Certification label, etc During maintenance or inspection When handling suppliesDisclaimer Notice PorationEnvironmental Information Energy Star programmeDescription of Each Component Preparation 1 Turning Power onPreparation 2 Placing Copy Paper Description of Each Component Front / Right sidePlaten Cover Automatic Document Feeder optional, MR-2017Left side / Inner side USB terminal 4-pin Receiving tray Scanning areaOriginal scale Platen sheetConfiguration of options Control panel Original mode button/lamps Density adjustment buttons/lampsLED display Copy qty. / zoom display selecting button/lampOriginal setting lamp Drawer button/lampsCopy button/lamps Original button/lampsTurning power on Preparation 1 Turning Power onTurning power OFF To turn the equipment into the energy saving mode manually Saving energy when not in use Energy saving modeCancelling the energy saving mode Acceptable media types Preparation 2 Placing Copy PaperFeeder Media type Paper size Maximum sheet Capacity *1 Recommended paper Paper types not acceptableStoring paper Media type Product namePlacing paper in drawers Press down the paper plateWiden the gap with both hands Adjust the side guides to the desired paper size Place paper in the drawerDo not let your fingers be caught when closing the drawer Register the paper size into the equipmentPreparation 3 Registering Size of Paper Placed Registering standard size A3, A4, A4-R, A5-R, B4Registering other standard sizes Code NoPreparation 3 Registering Size of Paper Placed Press the Start button Placing Originals Using Bypass TrayMaking Copies When the built-in memory has become full during scanning Setting position Type of origiPlacing Originals Acceptable originalsPlacing originals on the original glass Placing booklet-type originals such as books or catalogues Using Automatic Document Feeder optional Precautions for Automatic Document Feeder optionalWhen black streaks appear on the copied image Media types Maximum size Maximum number Paper weightWhen placing a large amount of originals with a long width Placing originals on Automatic Document Feeder optionalMaking Copies Check if paper is placed in the drawerPlace the original Select the copy modes as requiredWhen the number of sheets exiting has exceeded When the paper has run outStopping/Resuming copying Press the CLEAR/STOP button during scanning or copyingInterrupting copying and making another copy Interrupt copy Press the Interrupt buttonUsing Bypass Tray Media type Paper size Maximum sheet Capacity *1Preparation Registering paper size placed on bypass tray ST-R Folio Comp Using Bypass Tray Press the Start button Bypass copying on standard size paper Placed on the bypass tray is lit Using Bypass Tray Page Zooming In/Out Copy Image Default Settings Paper SelectionAutomatic paper selection APS Manual paper selection Default Settings Contents Default setting at installationPaper Selection Automatic paper selection APSPlace the original on the Automatic Document Feeder Automatic paper selection APSManual paper selection Place paper in the drawer Place the originalSelecting the drawer of the equipment Zooming In/Out Copy Image Automatic magnification selection AMSAutomatic magnification selection AMS Specifying reproduction ratio manuallyIf the Function Clear lamp is blinking and copying stops Specifying both the sizes of the original and the copy paper Specifying reproduction ratio manually Press Zooming out orDesired reproduction ratio appears Zooming in button untilZooming In/Out Copy Image Copying in Same Page Order as Originals Sort Copying Selecting Image Mode Adjusting Density Level To adjust the density to the desired levelTo return it to the automatic copy density mode DarkPage Settings and Management of Equipment Switching Operation Sound On/Off All lamps on Sound on All lamps off Sound offChecking Total Number Copied Switch the display to check the rest of the total numberPress Button for more than two seconds Page Troubleshooting When Message Lamp is Lit/Blinking Paper JamsWhen Message Lamp is Lit/Blinking Cover open lampPaper empty lamp Toner lampRecommended toner cartridges Service call lamp Paper jam lampPaper Jams When paper jams occur frequentlyChecking position of paper jams When releasing jammed paper Paper jams within Automatic Document Feeder optionalRaise the lever, and then open the upper cover Do not tear jammed paperPaper Jams Paper jams on bypass tray Pull out the paper jammed on the bypass trayPaper jam behind transfer unit Paper jams within fuser unit Close the transfer unit and the side coverPaper Jams Paper jams within Paper Feed Unit optional Open the front cover Replacing Toner CartridgeHold down the green lever Pull out the toner cartridge Clean the charger Replacing Toner Cartridge With the transfer charger wire General operation Before Calling Service TechnicianPhenomenon Usual cause Countermeasure Toner-related items Original/Copy paper-related itemsImage trouble Tion Charger is dirty Clean the charger Page Maintenance and Inspection Daily Inspection 100Daily Inspection Original glass Guides Platen sheetCleaning charger Open the front cover Clean the chargerCleaning transfer charger Daily Inspection Page Specifications and Options STUDIO166/206 Specifications OPCContinuous copying speed Paper size Feeder STUDIO166 STUDIO206Automatic Document Feeder Specifications of OptionsPaper Feed Unit Packing List Page Index 106 DP-1660/2060 OME06015700 Multifunctional Digital Systems